Fall Protection /Strong Tensile /Mountain Climbing Steel Carabiner Cold formed steel,Heat treated Gate Size:17mm Min. Breaking load:5000lbs/25kN Net weight:176g Meets or Exceeds:EN362-2004
Fall Protection /Strong Tensile /Mountain Climbing Steel Carabiner Cold formed steel,Heat treated Gate Size:17mm Min. Breaking load:5000lbs/25kN net weight:176g Meets or Exceeds:EN362-2004
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills. It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color. Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating. From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list In particular the mill scale can be classified as follows: Einecs (european commission no.): 266-007-8 Waste code: 10 02 10 Basel code: b 12 30 Hs code: 2619.00
We offer a wide plethora of Zinc in many forms including LME registered and non registered Special High Grade Ingots and Jumbos, cathodes, dust, foil, granules, powder, pieces, anodize activated powder, shot, and a mossy form. Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
Fuels products of: ja54, jet a1, d6, diesel gas d2, ultra low sulfur diesel, en590, light cycle oil, ago (automotive gas oil), rebco, liquefied natural gas, lpg, espo blend crude oil, and any other fuel products such as asphalt, petroleum coke, mazut 75 & 100 bitumen 60/70, bitumen 80/100. urea n46% prilled & granular. mineral fertilizers to the agricultural sector russian origin urea 46% prilled & granular npk fertilizers. di ammonium phosphate (dap) 18 46 0 automotive grade prilled urea adblue diesel exhaust fluid (def) high purity imidazolidinyl urea metal products of: used rail, steel billets, copper cathodes, copper millberry, aluminum ingot, iron ore, coal, copper powder, and any other metal products. agriculture products such as palm oil, icumsa 45 sugar, crude/refined soybean oil, gmo/nongmo soybeans, common wheat, yellow corn, olive oil, sunflower oil etc... meat chicken paws and feet and pork, beef, etc... syringes (made in korea), test kit, ppe.
Product of Unilever Indonesia. Lifebuoy Products & Variants: 1. Body Wash: Cool Fresh, Lemon Fresh, Matcha Green Tea, Mild Care, Nature Pure, Total 10, Vita Protect. 2. Shampoo: Anti Hair Fall, Anti Dandruff, Hairfall Treatment, Strong & Shiny 3. Soap : Cool Fresh, Kasturi Musk, Lemon Fresh, Matcha Green Tea, Mild Care, Total 10.
Commodity:Avobenzone CAS No. 70356-09-1 Molecular Formula C20H22O3 Molecular Weigh 310.39 EINEC No. 274-581-6 Specification Quality standard: USP36 Appearance Off-white powder Assay 95.0-105.0% Melting range 81.0~86.0 Impurities Any individual impurity: 3.0% The sum of all of the impurities: 4.5% Loss on drying 0.5% Packaging and storage: 1kg/aluminum foil bag. 25kg/barrel, pharmaceutical packaging barrel. Sealed, stored in dark, with a shelf life of 2 years. Reference dosage: The hygiene standards for cosmetics stipulate that the maximum amount added shall not exceed 5%, and the general dosage is 1-4%. Usage: Sunscreen agent-1789 is the most effective fat soluble UVA filter and is a safe and effective UVA sunscreen approved by the US FDA for sale on the counter. It can effectively block UVA, thereby increasing the SPF value of sunscreen products. It can improve the efficacy of sunscreen products when used in combination with UVB filters, and BL-200 has the best effect when used in combination with octyl methoxycinnamate. BL-200 can increase its stability in the product. It has an extremely effective protective and repairing effect on human skin. Application: This product is soluble in oil and can be formulated into a cream using the usual method. However, the product turns red when it encounters metal ions, so other components such as formula water should not introduce metal ions. The equipment should be made of pure stainless steel, and an appropriate amount of EDTA-2Na should be added to the formula water phase to chelate with metal ions.
Paperboard expanding and cutting machine, The paper board expanding and cutting machine is used for the end customers of corrugated box (color box), and it is used as the filling or cushioning material in the packaging in the manufacturing industry; Such as precision instruments, meters, electrical appliances, ceramics, glass, crafts, furniture and other industries. It can deal with irregular waste cardboard, unqualified cartons, color cartons and cartons, with or without printing, and can solve the thorny problems of enterprise managers. Paper products, recycling, no pollution sources; The state explicitly forbids "non degradable products" as filling materials, which can be used as substitutes for some chemical products. Paperboard expanding and cutting machine features : Green environmental protection. 2. Reduce cost. 3. Waste utilization. 4. Wide use. Paperboard expanding and cutting machine advanced technology : The paper board expanding and cutting machine uses German technology to provide you with high quality green packing and filling materials; The unique technology turns the corrugated boxes that need to be discarded into "free" soft and fluffy green packing filling materials, and is used in the transportation packaging of fragile goods; The main switch is also an emergency brake to ensure safety; This product is widely used in packaging industry, transportation industry and parts processing industry. For example, motor manufacturers use fluffy paperboard as filler to facilitate logistics transportation; Small space and easy operation; A variety of specifications to choose from, with super large production capacity. Welcome order! good price good quality !
Natural Red Iron Oxide: Natural Red Iron Oxide is the most widely occurring Minerals in Earth. It is widely used in many applications due as it is economical as compared to Synthetic Oxides. Applications : Red Oxide is anti-corrosive and has inertness to alkali and chemicals which makes its very viable for making of paint, protective coating for steels, cement coloring, NPK Fertilizers, paving tiles. Packing : 25Kgs Bags.
Micro Silica Sand: Micro silica also known as fume, is an amorphous (non-crystalline) polymorph of silicon dioxide, silica. It is an ultrafine powder collected as a by-product of the silicon and ferrosilicon alloy production and consists of spherical particles with an average particle diameter of 150 mm. The main field of application is as pozzolanic for high performance concrete because of its extreme fineness and high silica. Applications : Silica is added to Portland cement concrete to improve its properties, in particular its compressive strength, bond strength, and abrasion resistance. These improvements stem from both the mechanical improvements resulting from addition of a very fine powder to the cement paste mix as well as from the pozzolanic reactions between the silica fume and free calcium hydroxide in the paste. Advantages : Addition of silica also reduces the permeability of concrete to chloride ions, which protects the reinforcing steel of concrete from corrosion, especially in chloride-rich environments such as coastal regions and those of humid continental roadways and runways (because of the use of deicing salts) and saltwater bridges.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Steaming Kettles Cordless Kettle 8147 Colour : Black 1350W Power 1.0 Litre Capacity Mirror Finish Hygienic Stainless Steel Body Over Heat and Boil Dry Protection Automatic Cut-off 360 degree Swivel Base for Ease of Use Hygienic Concealed Heating Element to Prevent Calcification with SS and Aluminum Die Cast Body for Extreme Long Life Wide Mouth-Easy to Clean Elegant Handle with Single Touch Lid Locking Convenient Spout Power ON Indicator Light 1 year waranty
Smart Home Appliances Multi function Kettle OEK 8167 Color : Black 650W Power 1.2 Litre Capacity Mirror Finish Hygienic Stainless Steel Body with High Grade Flat Glass Lid Over Heat and Boil Dry Protection 360 degree Swivel Base for Ease of Use Adjustable Temperature Control Knob Hygienic Concealed Heating Element to Prevent Calcification with SS and Aluminum Die Cast Body for Extreme Long Life Indicator Light Comfortable Handle Can be Used for Boiling Water Milk Tea Coffee Soup Cooking Noodles Cook & Steam Eggs Warm up and Reheat Food Extra Attachment Boiling Rack 1 year warranty
Steaming Kettles Smart Home Appliances Cordless Kettle OEK 8137 Black 1350W Power 1.2 Litre Capacity Mirror Finish Hygienic Stainless Steel Body Over Heat and Boil Dry Protection Automatic Cut-off 360 degree Swivel Base for Ease of Use Hygienic Concealed Heating Element to Prevent Calcification with SS and Aluminum Die Cast Body for Extreme Long Life Wide Mouth-Easy to Clean Elegant Handle with Single Touch Lid Locking Convenient Spout Power ON Indicator Light 1 Year warranty
Materials: carbon steel and stainless steel (302,304,304L,316,316L etc). Characteristics:The welded stainless steel water well screen is made up of rods and warp. The rod can be round wire, triangular wire or trapezoid wire. The warp is triangular wire (V-shaped wire). Water well screens have a structure and high open area, as well as accurate slot dimension. At the same time, water well screen have heat-resisting, anti-corrosive, good machine capability, last long, safety and reliability and so on characteristics. It can be used in many kinds of medium filtering. Uses: The strainer is a kind of filtered water tubing with the perforation .it can use with the deep well pump, dive the water pump, also may use in the water-treating equipment, the environmental protection, the sea water transforms into the industrial water and life use water desalination treatment, running water treatment, water softening treatment, the petroleum industry: The petroleum product terminal filters and the chemical acid, the alkali liquid filters, the ethyl alcohol and so on the organic solution recycling filters. Continuous slots significantly increase discharge area,thus providing greater access to water-bearing zone . We can produce this pipe with diameter 80mm-550mm ,slot size 0.1mm-10mm,length 50mm-5850mm .
Hand Max KG3 is the best welding gloves for advanced hand protection. - Material : Cowhide - Size : Free - Length : 23cm - Origin : India - Color : White - Packing : 1pair/Individual packing (1pack=10pair, 1box=100pair) - Use : Multi-purpose (welding, steel industry, civil engineering, construction site, camping/outdoor, etc)
Type - Disposable/ Refillable Shape - Stick Size - J5 / J6 / J23 / J25 / J26 Color - Multi-color Dimension - 76.7mm*21.9mm*10.8mm Material - ABS & AS, Plastic, Steel and Metal Rate of Leaking - Less Than 0.3% Rate of Inflaming - Over 98% Resit Water - 55 C 50 pieces in a single tray , 20 trays / carton ,63 cartons / palette ,23 pallets /20'FCL. - Smooth and bright without trace of scratch or shrunken signs - The rate of inflaming is over 98%, the inferior lighters is under 0.6% - The time of continual inflaming can reach 2 minutes - The tank would not explode when falling down within 1.5 meters high - Plastic lighters,refillable, good hand feeling, Competitive price & high quality, Cheap price
Type - Disposable/ Refillable Shape - Stick Size - J5 / J6 / J23 / J25 / J26 Color - Multi-color Dimension - 76.7mm*21.9mm*10.8mm Material - ABS & AS, Plastic, Steel and Metal Rate of Leaking - Less Than 0.3% Rate of Inflaming - Over 98% Resit Water - 55 C 50 pieces in a single tray , 20 trays / carton ,63 cartons / palette ,23 pallets /20'FCL. - Smooth and bright without trace of scratch or shrunken signs - The rate of inflaming is over 98%, the inferior lighters is under 0.6% - The time of continual inflaming can reach 2 minutes - The tank would not explode when falling down within 1.5 meters high - Plastic lighters,refillable, good hand feeling, Competitive price & high quality, Cheap price