Waterproof Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor Probe 15m Description Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor Ampfort DS18b20 temperature detector probe adopts the brand-new and original DS18B20 temperature sensor chip, chinese brand chip , GX18B20 produced by Beijing Zhongke Galaxy Core Technology Co., Ltd. belong to scientific research technology resources of the Institute of microelectronics, Chinese Academy of Sciences if you have cost pressure. Each pin of chip is separated by heat shrinking tube to prevent the short circuit, and sealed inside for waterproof and damp-proof. Its direct "One line Bus" digital transmission greatly improves the anti-jamming capability of system, suitable for field temperature measurement in harsh environments. At the same time, it is sealed with a high thermal conductivity of sealing rubber strip, to ensure the temperature sensorâ??s high sensitivity, with a very tiny temperature delay. Its measured temperature range is from -55 to +125, in the range of -10~ +85, its accuracy is ±0.5. When testing it, need to connect the signal end (yellow line) of sensor to the Digital port of microcontroller, meanwhile, need to add a pull-up resistor on the Signal end, or else the test will fail. Features Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor * 3.0V ~ 5.5V power supply * 9 to 12 adjustable resolution * Wide temperature range of -55 ~ +125 * No external components, a unique single-bus interface * Red (VCC), yellow (DATA), green (GND) * Output leads: red (VCC), white (DATA), black (GND) * Every pin of the chip is sealed and separated by the heat shrink tube. Good for insulation and to prevent short circuit. 3 output lines, * * * * * * VCC/DATA/GND. The exterior is made of PVC plastic tube, which is safe, wear-resistant and waterproof. * The high quality 304 stainless steel probe, is resistant to high temperature, fast heat conduction and accurate reading. * The sensor has one unique number and the temperature acquisition device identifies the corresponding temperature sensor by number. * The field temperature is directly transmitted in the digital way of 1-Wire bus, no need the external components and greatly improves the system's anti-interference. Suitable for the harsh environments. Internal Wiring Diagram Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor DS18B20 26AWG Cable Power NTC Thermistor 15m Digital Temperature Sensor Probe 2 Pin 1 Soldering to black GND ; Pin 2 Soldering to white DQ ; Pin 3 Soldering to red VDD;
Supply range:3.0V to5.5V Temperature range:-55 to +110degree Celsius Wire length:1M/2M/5M...50M optional Material:stainless steel sheath Output:3-wire: Red:+ Black:_ Yellow:signal line Basic Info Model NO.: UN-CL37HP Teeth Whitening Method: Cold Light Whitening Certification: ISO, CE Material: PVC Medical Devices Reg./Record No.: Ehsyjxjyb20150324 Wave Length: 420-480nm MOQ: 5 Transport Package: Carton Origin: China Interface: 4 Holes Applicable Departments: Oral Department of Internal Medicine Type: Mechanic Equipment Medical Device Regulatory Type: Type 2 Working Voltage: AC100-240V, 50/60Hz Light Intensity: 800 MW/Cm²-1200 MW/Cm² Trademark: UN Specification: 800g HS Code: 9018499000 Product Description Dental LED curing light with 4 working modes Function and Features: * Double function : the Blue light for curing and the Purple light for Caries detector. * Press M button to change function, no need any other thing to help! * Use purple light to illuminate teeth, Caries will show Red color, Healthy teeth will show white color. It will help dentist to remove caries exactly. * 4 working model : Strong light, Gradually light, Pulse ,and Pre-heating .(The first 10s is with 50% power light, the rest time is full power light) * Germany material fiber optic light tip with high articulation. * LCD Sreem display the working situation clearly . * Constant light intensity output ,it will not be effected whatever the battery is lower or full power. * High efficiency for exchange rate from electricity to light. A full charge can be used for more than 200 times continously . * Bionic sreamline design ,luxury and comfortable to operate. * Humanized design with battery easy to replace. * Automatically detection function of charging voltage * Double protection board for battery * Using USA imported circuit chips. * Using BYD battery * The standby time can be 1 year. Application Range: It can be used for any brand of resin material. Technical Data: Working voltage for adapter: AC100-240V, 50/60HZ Wave length: 420-480nm Light intensity: 800 mW/cm²-1200m mW/cm² Packing: Dimension: 22*16*15cm GW: 800g
Model FZK8810A QY-EWQ-01 Measurement Method Non-contact type Power Supply Prompt for low battery charge DC 3V(2 AAA batteries) Measuring Range 32-42.5 33~43.0 Electricity Prompt Prompt for low battery charge Measure Distance 1cm-15cm 3~5cm Fever Alarm Abnormal body temperature alarm 5 beeps in case of the temperature is higher 38 Measuring Time Measurement time:0.6 second Maximum Error ±0.2 0.2~0.3 Display Unit Centigrade() Display Resolution 0.1 0.2~0.3 Automatic Shutdown 15 seconds 20 seconds Operating Environment 10-40, Humidity 85% Specification Size 7cm*5cm*19cm 15.5*8.77*4.4cm Transportation And Storage Environment -20 -55,Humidity 85%
2-Naphthol Basic information Chemical Properties Application Preparation Product Name: 2-Naphthol Synonyms: c.i.37500;c.i.azoiccouplingcomponent1;c.i.developer5;Developer A;Developer AMS;Developer BN;developera;developerams CAS: 135-19-3 MF: C10H8O MW: 144.17 EINECS: 205-182-7 Product Categories: Fluorescent;Naphthalene;pigments;alcohol;MICROCIDIN;Color Former & Related Compounds;Developer;Functional Materials;Intermediates;Aromatic Compounds;Alphabetical;Bioactive Small Molecules;Biochemicals and Reagents;Building Blocks;C9 to C20+;Cell Biology;Chemical Synthesis;Fluorescent Indicators and Probes;Fluorescent Probes;Labels;N;Organic Building Blocks;Oxygen Compounds;Particles and Stains;pH Sensitive Probes and Indicators;Phenols;Dyestuff Intermediates;Aromatics Mol File: 135-19-3.mol 2-Naphthol Chemical Properties Melting point 120-122 C(lit.) Boiling point 285-286 C(lit.) density 1,28 g/cm3 vapor density 4.97 (vs air) vapor pressure 10 mm Hg ( 145.5 C) refractive index 1.5762 (estimate) Fp 153 C storage temp. Refrigerator solubility methanol: soluble1g/10 mL, clear, colorless to light yellow pka 9.51(at 25C) form Powder, Crystals or Granules color White PH Range Non& uorescence (8.5) to blue & uorescence (9.5) Water Solubility 1 g/L (20 C) �»max 226nm, 265nm, 275nm, 286nm, 320nm, 331nm Merck 14,6384 BRN 742134 Stability: Stable. Combustible. Dust may form explosive mixture with air. Incompatible with strong oxidizing agents, phenol. Major Application Display device, semiconductors, photoimaging materials, inks, toner, chalk, security paper, molding materials, tin plating method, rubber, adhesive, leather, detergent, hair dyes, antimitotic drug, anticancer agent, antiinflammatory agent, treatment of acne vulgaris (pimples) and other dermal ailments (rashes, scratches, blemishes, hair loss), disorders InChIKey JWAZRIHNYRIHIV-UHFFFAOYSA-N CAS DataBase Reference 135-19-3(CAS DataBase Reference) NIST Chemistry Reference 2-Naphthalenol(135-19-3) EPA Substance Registry System 2-Naphthalenol (135-19-3) Safety Information Hazard Codes Xn,N Risk Statements 20/22-50 Safety Statements 24/25-61 RIDADR UN 3077 9/PG 3 WGK Germany 2 RTECS QL2975000 F 8 Autoignition Temperature 430 C TSCA Yes HazardClass 9 PackingGroup III HS Code 29071590 Hazardous Substances Data 135-19-3(Hazardous Substances Data) Toxicity LD50 orally in Rabbit: 1960 mg/kg LD50 dermal Rabbit > 10000 mg/kg 2-Naphthol Usage And Synthesis 2-Naphthol Preparation Products And Raw materials
Type: k/j/e/n/t Temperature range: 0-350¡æ Probe length: 50~1000mm Probe diameter: 3.0~20.0mm Installation: thread or flange 1 piece per box and 15 boxes per carton
Take temperature readings from a distance, or underwater, using this Waterproof DS18B20 Digital Temperature Sensor. It's got a 90cm (0.9m) cable with a stainless steel, PVC coated probe at the end. You'll be able to use it with any 3V-5V system, and take temperature readings with an accuracy of 9-12 Bits (configurable in code). The best part is that it's digital, meaning you won't suffer any signal degradation over the longer distance. Waterproof - Take the temperatures of liquids/moist environments with the stainless steel probe. It's shrouded in PVC plastic too, meaning it will hold it's own in temperatures up to 100 degrees Celsius. Temperature - Usable from -55 degrees Celsius to 125 degrees Celsius. Accuracy of 0.5 degrees. Digital - The digital interface used to relay the readings guarantees minimal signal degradation over the longer distances (90cm for this standard cable) 1-wire interface - You can have multiple DS18B20s connected to the same central micro-controller pin as each device has a unique identifier hard-coded in. Long range - 1.5 meters of cable by default, but you can make it longer if needed Maker friendly - The DS18B20 chip is able to be powered with 3v - 5.5v which is perfect for maker platforms . HOOK-UP GUIDE This sensor is simple, you've got 3 wires (Power, Ground and Data). You simply need to connect the data pin to an input pin on your micro-controller and the power and ground to power and ground You'll also need to connect a resistor between power and signal wires, as shown in the circuit diagram on the Sensor's wiki page. Specifications TECHNICAL SPECIFICATIONS Compatible with 3.0V to 5.5V systems (development board etc) Within 0.5 degrees Celsius accuracy Recommended usable temperature range: -55 to 125 degrees Celsius Select-able 9-12 bit resolution (Factory Default at 12-bit) 1 Wire Interface Unique 64 bit ID for each sensor Query time is less than 750ms Stainless steel tube 6mm diameter by 35mm long Cable diameter: 4mm Cable Length: 90cm 100cm 200cm or Customized Technology character
We manufacture a stock range of probes to suit the hand hold thermometers and will manufacture custom assemblies to suit your applications for food, liquid, surface, air, compost and immersion temperature measurement. 50 pcs * 5 bundles * 4 packs/carton(small quantity packs packs separately); or customized
Specifications: Wide operating temperature range: -20 to 125 degree celsius Dielectric strength: 1, 500v ac for one second Short thermal response time in water, high stability in moisture Suitable for use in high-temperature and moisture environments High accuracy, different tolerance available, cost-effective Customized specifications are welcome Standard export packaging or customized
DTZ-400G Series Surface Temperature Calibration System is primarily used to calibrate surface sensors of various sizes and types, such as thermistors, film sensors, surface resistance thermometers, ribbon sensors, surface thermocouples, and more. The product consists of a controller and a heater. It is easy to operate, intuitive to display, and can be heated simply by setting the temperature.The temperature rises rapidly and the multi-stage PID temperature control is accurate. The effective use range is up to 130mm in diameter and has a communication interface to communicate with the computer. This product can be used as an infrared camera calibration source if it is slightly changed. Product Features 1.The calibration temperature can reach 400 The temperature rises and the temperature drops quickly. DTZ-400 surface temperature calibration system has a good temperature rise and fall, from room temperature to 400, only 30 minutes, from 400 to room temperature, with a rapid cooling device only 50 minutes, greatly improving work efficiency . 2.Calibration plate diameter up to 130 mm, meeting most surface temperature sensor calibration needs 130mm and is sufficient for calibrating surface sensors of various sizes and types, such as thermistors, film sensors, surface resistance thermometers, ribbon sensors, surface mount thermocouples, etc. 3.External reference platinum resistance thermometer to reduce calibration uncertainty In order to achieve the ultimate in calibration accuracy, the design engineer deliberately reserved a thermometer socket at the bottom of the aluminum surface. platinum resistance thermometer with a diameter of 5 mm can be inserted as a standard for comparison and calibration, which greatly improves the calibration accuracy. 4.Excellent uniformity of temperature and surface finish on the calibration plane Surface sensors are often difficult to calibrate because it is difficult to find a flat, uniform source of surface temperature.The DTZ-400 Surface Temperature Calibration System utilizes aluminum as the surface and has a high finish that ensures that the calibrated sensor is in good contact with the surface temperature calibrator, reducing calibration uncertainty. The DTZ-400 uses a special heating material and a constant temperature structure to make the surface temperature more uniform. 5.Temperature control is accurate, stable, and overshoot temperature is small The device provides a variety of parameter options for the user to choose, including setting the PID parameters of the high,medium and low temperature segments, the inflection point between different temperatures, and the alarm temperature. 6.Portable and easy to use The weight of the whole machine is only 3.5kg, which is small and portable.
Waterproof Meat Probe Thermistor Temperature Sensor 3.3K For Stove Oven Grill Baker I Description Of Thermistor Temperature Sensor A meat thermometer is a unit which will measure core temperature of meats while cooking.It will have a metal probe with a sharp point which is pushed into the meat. It should be connected by a flexible heat-resistant silicone cable to oven control board & display. Some brand models have programmed for auto cooking with the meat probe.
The coolant temperature sensor consists of a negative temperature coefficient thermistor that is very sensitive to temperature changes.When the engine coolant temperature gradually increased,Thermistor resistance will gradually decline,On the contrary increases,When the engine coolant temperature changes,The output voltage of the sensor also changes accordingly. Engine coolant temperature sensor elongated head contact with the cooling liquid,The temperature of the coolant is detected by the change of the resistance value,And this signal is sent to the ECU,Used to detect the engine coolant temperature.The ECU corrects the fuel injection time and the ignition time after receiving the temperature signal. The normal use of the coolant temperature sensor is -30 ° C to 120 ° C,The corresponding output voltage is 0.3V ~ 4.7V.When the ECU detects an output voltage signal beyond this range,You can determine the sensor circuit failure. Car intake air temperature sensor (IATS) Automotive coolant temperature sensor (CTS) automobile exhaust gas temperature sensor (Ex-haust Air Temperature Sensor, EATS) car was NTC thermistor / temperature sensor Car temperature sensor,Respectively, water temperature sensor,Exhaust | intake air temperature sensor,These types of sensors are thermistors with the same characteristics,The temperature coefficient is negative temperature coefficient.The water temperature sensor is mounted on the engine cooling water passage,Its role is to detect the engine cooling water temperature,The water temperature sensor housing is fully enclosed,Use the change of resistance value to detect water temperature.The signal temperature value generated by the water temperature sensor is input to the ECU,ECU according to the cooling water temperature ignition control,Correction fuel injection amount to real-time control of the engine,To ensure the normal operation of the engine under different conditions. Intake | outlet temperature sensors are installed,Within the housing of the air cleaner box or regulator,The air flow meter or an intake manifold,Used to detect the temperature of the engine inhaled air.As the intake air temperature changes will affect the air density,The hotline, hot film cooling strength and the degree of atomization of the mixture have an impact,Intake air temperature sensor,Provide a signal to correct this effect.
The coolant temperature sensor consists of a negative temperature coefficient thermistor that is very sensitive to temperature changes.When the engine coolant temperature gradually increased,Thermistor resistance will gradually decline,On the contrary increases,When the engine coolant temperature changes,The output voltage of the sensor also changes accordingly. Engine coolant temperature sensor elongated head contact with the cooling liquid,The temperature of the coolant is detected by the change of the resistance value,And this signal is sent to the ECU,Used to detect the engine coolant temperature.The ECU corrects the fuel injection time and the ignition time after receiving the temperature signal. The normal use of the coolant temperature sensor is -30 ° C to 120 ° C,The corresponding output voltage is 0.3V ~ 4.7V.When the ECU detects an output voltage signal beyond this range,You can determine the sensor circuit failure. Car intake air temperature sensor (IATS) Automotive coolant temperature sensor (CTS) automobile exhaust gas temperature sensor (Ex-haust Air Temperature Sensor, EATS) car was NTC thermistor / temperature sensor Car temperature sensor,Respectively, water temperature sensor,Exhaust | intake air temperature sensor,These types of sensors are thermistors with the same characteristics,The temperature coefficient is negative temperature coefficient.The water temperature sensor is mounted on the engine cooling water passage,Its role is to detect the engine cooling water temperature,The water temperature sensor housing is fully enclosed,Use the change of resistance value to detect water temperature.The signal temperature value generated by the water temperature sensor is input to the ECU,ECU according to the cooling water temperature ignition control,Correction fuel injection amount to real-time control of the engine,To ensure the normal operation of the engine under different conditions. Intake | outlet temperature sensors are installed,Within the housing of the air cleaner box or regulator,The air flow meter or an intake manifold,Used to detect the temperature of the engine inhaled air.As the intake air temperature changes will affect the air density,The hotline, hot film cooling strength and the degree of atomization of the mixture have an impact,Intake air temperature sensor,Provide a signal to correct this effect.
The coolant temperature sensor consists of a negative temperature coefficient thermistor that is very sensitive to temperature changes. When the engine coolant temperature gradually increased, Thermistor resistance will gradually decline, On the contrary increases, when the engine coolant temperature changes, the output voltage of the sensor also changes accordingly. Engine coolant temperature sensor elongated head contact with the cooling liquid, the temperature of the coolant is detected by the change of the resistance value, and this signal is sent to the ECU,Used to detect the engine coolant temperature. The ECU corrects the fuel injection time and the ignition time after receiving the temperature signal. The normal use of the coolant temperature sensor is -30 ° C to 120 ° C,The corresponding output voltage is 0.3V ~ 4.7V.When the ECU detects an output voltage signal beyond this range,You can determine the sensor circuit failure. Car intake air temperature sensor (IATS) Automotive coolant temperature sensor (CTS) automobile exhaust gas temperature sensor (Ex-haust Air Temperature Sensor, EATS) car was NTC thermistor / temperature sensor Car temperature sensor,Respectively, water temperature sensor,Exhaust | intake air temperature sensor,These types of sensors are thermistors with the same characteristics,The temperature coefficient is negative temperature coefficient.The water temperature sensor is mounted on the engine cooling water passage,Its role is to detect the engine cooling water temperature,The water temperature sensor housing is fully enclosed,Use the change of resistance value to detect water temperature.The signal temperature value generated by the water temperature sensor is input to the ECU,ECU according to the cooling water temperature ignition control,Correction fuel injection amount to real-time control of the engine,To ensure the normal operation of the engine under different conditions. Intake | outlet temperature sensors are installed,Within the housing of the air cleaner box or regulator,The air flow meter or an intake manifold,Used to detect the temperature of the engine inhaled air.As the intake air temperature changes will affect the air density,The hotline, hot film cooling strength and the degree of atomization of the mixture have an impact,Intake air temperature sensor,Provide a signal to correct this effect.
Food meat smoker oven machine cooking ,drying ,baking ,fumigation ,exhaust,cleaning and other functions. The fast and slow cycle procedure can be selected according to the process requirements to achieve the best cycle and smoke effect .2.can monitor the smoke temperature,prevent the temperature is too high ,safe and sanitary .3.various types of temperature sensors are available for users to choose. 4.add water circulation cleaning device . capacity 50-1000kg
Parameters: 1)storage temperature: -40 to 125ºc 2)supply voltage: 3.8v 3)humidity operating range: 1-100%rh 4)temperature operating range: -40 to 125ºc 5)vdd to gnd:-0.3 to 3.6v 6)digital i/o pins (data/sck) to vdd:-0.3 to vdd+0.3v 7)-10 to +10 ma Features: (1)dfn type package (2)relative humidity and temperature digital output, i2c interface (3)fully calibrated (4)lead free sensor, reflow solderable (5)low power consumption (6)fast response time and very low temperature coefficient Isweek provide smoke, gas, humidity&temperature, uv, fluid or other kinds of sensors More details welcome to inquiry: skype:isweek_laura
2-head packaging machine (also can 4-18head according different capacity choice) Packaging speed 15bags/min Bag length 90-320mm Bag width 80-210mm Overall weight 400kg Power 1.8kw/220v Packaging capacity 20-1000ml Outer packaging size 820 x1220 x 2500mm Packaging form Back sealing This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc. Performance characteristics: 1. High precision digital sensors enable precise measurement to be achieved instantly. 2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use. 3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging. 4. Four scales work alternately, with fast packaging speed. 5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean. Host configuration: This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.
The coolant temperature sensor consists of a negative temperature coefficient thermistor that is very sensitive to temperature changes.When the engine coolant temperature gradually increased,Thermistor resistance will gradually decline,On the contrary increases,When the engine coolant temperature changes,The output voltage of the sensor also changes accordingly. Engine coolant temperature sensor elongated head contact with the cooling liquid,The temperature of the coolant is detected by the change of the resistance value,And this signal is sent to the ECU,Used to detect the engine coolant temperature.The ECU corrects the fuel injection time and the ignition time after receiving the temperature signal. The normal use of the coolant temperature sensor is -30 , C to 120 , C,The corresponding output voltage is 0.3V ~ 4.7V.When the ECU detects an output voltage signal beyond this range,You can determine the sensor circuit failure. Weichai water temperature sensor 612600090673/612600090673 Dongfeng Tianlong, day Kam water temperature sensor water temperature plug / 0281002209 / D5010412450 Weichai Europe three cooling water temperature sensor 612600090919/612600090919 Nanchong natural gas engine 36.2D-02012 water temperature sensor assembly (ECU) / 36.2D-02012 FAW Xichai engine 6110 accessories water temperature alarm sensor / 3818010-001-0010 Dongfeng warrior accessories EQ2050 - water temperature is too low / too high sensor / 3839C21-010 Cummins water temperature sensor diesel generator set temperature alarm switch / 3408627 Natural gas engine water temperature sensor 3602160-55D Heavy Duty Hau Wo LNG Natural Gas Engine Cooling Water Temperature Sensor / R61540090004 Weichai WP10 water temperature sensor 612600090358 Nanchong natural gas engine water temperature sensor 36.2D-02012 / 36.2D-02012 Weichai engine country 3 EFI cooling water temperature sensor 612630060035 Chongqing Cummins engine M11 water temperature sensor 4921477 Shiyan Auto Parts City / 4921477
Digital Temperature Humidity Sensor HTU21D In Stock 1. digital temperature and humidity sensor 2. range:1-100%RH 3. original, high quality, competitive price DESCRIPTION HTU21D, the new humidity and temperature sensor of MEAS is about to set new standards in terms of size and intelligence: Embedded in a reflow solderable Dual Flat No leads (DFN) package of 3 x 3mm foot print and 1mm height it provides calibrated, linearized signals in digital, I²C format. HTU21D sensors are dedicated humidity and temperature plug and play transducers for OEM applications where reliable and accurate measurements are needed. Direct interface with a micro-controller is made possible with the module humidity and temperature digital outputs. HTU21D sensors are low power consumption designed for high volume and cost sensitive applications with tight space constraints. Every sensor is individually calibrated and tested. Lot identification is printed on the sensor and an electronic identification code is stored on the chip – which can be read out by command.
Place of Origin: Henan, China Brand Name: Comen Model Number: J638-1D Theory: Resistance Sensor Accuracy:99.9% Material: TPU MOQ: 1 Piece Length:3 meters Resistance:2.25k Connector:2 pin Color: Gray Packing: Individual pack, 1piece/bag Sample: Avaliable Other Service: OEM&ODM Cable diameter:Adult:3.0mm Pediatric:2.5mm Neonatal:2.0mm Keyword:Comen,Pediatric,Rectal/Esophageal, temperature sensor probe Temperature test range: 25 ~ 45 ; Accuracy: ±0.1°C from 25 to 45°C. Application site: Skin surface,Rectal/Esophageal Application: Adult, Pediatric, Neonatal Compatinle models:Use for Comen and Biolight monitor. Types: 1.Adult Rectal/Esophageal temperature probe; 2.Adult Skin surface temperature probe; 3.Pediatric Rectal/Esophageal temperature probe; 4.Pediatric Skin surface temperature probe; 5.Neonatal Rectal/Esophageal temperature probe; 6.Neonatal Skin surface temperature probe. Port:Shenzhen Delivery Time:3-5 days Supply Ability: 1000 Piece/Pieces per Week. Packaging Details:Separate package,then put in outer box. Payment Terms:L/C,D/A,D/P,T/T,Western Union,Money Gram Shipping Methods: 1. By express (DHL, FedEx, UPS, TNT, EMS, China Post), Door to door service. Takes about 5-7 days on the way. 2. By air, send order to airport. Have to pick up order at airport and do custom clearance. Takes about 3-5 days on the way. 3. By sea. Send order to seaport. Have to pick up order at seaport and do custom clearance. Takes about 1 month. Our Services 1.More competitive factory price. 2.Fast delivery (1-5 days, we are a manufacturer, have enough products in stock.) 3.Quality 100% assured (All products are made of medical TPU material) 4.Samples available (accept trial order) 5.One piece MOQ is acceptable. 6.OEM & ODM service. Warranty Period: All Spo2 Products 12 months ECG and EKG Products 6 months NIBP Hoses & Cuffs 3 months Temperature Probes 6 months IBP Products 6 months Ultrasound/TOCO/Fetal Probes 6 months O2 Sensor 12 months Main Products: 1.Reusable/ Disposable Spo2 Sensor 2.Spo2 Extension Cable 3.ECG/ EKG Cable with leadwires 4.ECG /EKG Trunk Cable 5.Temperature Probe 6.Fetal & TOCO Transducer 7.IBP Cable and Transducer 8.NIBP Cuff and hose
Stainless Steel Housing Temperature Sensor Chip NTC Thermistor 50K 1% 3950 100MM I Description Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor Ampfort offers Stainless probe assemblies suitable for a wide range of temperature sensing applications. If the dimensions and electrical characteristics on this product wonot work for your requirements, please contact us for further assistance. 1.Temperature probe features XH2.54-2P connector and 15.7 inch (40cm) in length. 2.Mainly used in air conditioner for monitoring temperature, has quick reaction speed. 3.Application : thermostatic controls, industrial systems, consumer products, thermometers, any thermally sensitive system. II Features Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor Tight Tolerance Moisture Resistant PVC Insulated Zip Cord 105�°C Max Operating Temperature Food grade stainless steel housing Custom and standard machined metal housings available in brass, stainless steel, aluminum, and exotic alloys Global engineering support for custom design solutions UL rated assemblies mateirals for HVACR applications IV Materials information Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor NO Material Name Item/PN Origin 2-1. Lead wire UL2651#26AWG*2C 105 300V White KL 2-2. Thermistor R25=50K±1% B25/50=3950K±1% MF58 SH 2-3. Epoxy Resin J105/J106B/J05X Black DB 2-4 Shell 5.0*25 Round Head Stainless steel shell XDL VIII Thermistor Thermistors are a type of resistor that acts as a temperature-sensing element, generally made of ceramic or polymer. Thermistors exhibit a large change in resistance proportional to a small change in temperature. Thermistors come in two common types: NTC (Negative Temperature Coefficient) thermistors In these thermistors resistance decreases as temperature rises. An NTC is commonly used as a temperature sensor, or in series with a circuit as an inrush current limiter. PTC (Positive Temperature Coefficient) thermistors â?? In these thermistors resistance increases as temperature rises. PTC thermistors are commonly installed in series with a circuit, and used to protect against overcurrent conditions, as resettable fuses.