All stainless steel construction
Easy cleaning and renewable by water
Multiple layer with stainless wire mesh
High velocity and low pressure loss
Dust weight arrestance 60~75% by ASHRAE 52.1
It is a daily issue the bathroom mirror is full of steam when you finished the shower, we offer bagen fog free mirror, as well as anti-frost mirror, defrosting mirror and steam free mirror, which is widely used in star hotels, and home shower mirror.
Features:
1) electric mirror defogger effectively transforms electric power into heating energy, which in return is transferred directly to the conductive mirror panel and resulting in the mirror surface's heating up
2) specially rated power and warm mirror temperature can effectively prevent condensation of steam on the mirror surface
3) dimensions can be tailored to meet customers' requirements
4) prevents moisture damage to silver coatings
5) reduces need for cleaning the fog
6) keeps mirror in place in case of unexpected breakage of mirror
We can make the demister mirror according to our clients' size.
DEMISTER PAD
EVAP
1000X432X100 MM
WIRE DIAMETER 0.28 MM
MESH DENSITY 144 KG/CU.METER
YORK STYLE 431
GRID:FLAT BARS 25 X 4 MM
6.0 MM DIA RODS AT VAPOR INLET END
4MM DIA. WIRES AT OUTLET END
TIE WIRE 2.0 MM DIA AT 8 TO 12 PLACES
THE PADS SHALL BE SUITABLY OVERSIZED FOR SNUG-FIT
CONSTRUCTED OF ASTM A478,316L(WIRE) AND A276-TYPE 316L
Pad; demister pads , denesity: 150 kg/m^3, free volume: 98.3%, surface area: 267 .5 m^2/ m^3, wire dia: 0.254 mm, pad material: ss316l, grids materials: ss316l, frame work made of round bar dia 6mm, the top and bottom grids are tied together with spacer rod 6mm dia roun d bar.
Demister
388ODX150MM,MONEL,3.4KG/CM2G
End Connection : INTERNAL
Material, Housing : SA 516 GR.60
Material, Separator : MONEL
Maximum Operating Pressure : 3.4 KG/CM2 G
Maximum Operating Temprature : 38 DEG C
Service, Fluid : GAS
Size : 388 OD X 150 MM
Type : MESH WIRE
DEMISTER
388ODX150MM,MONEL,10.9KG/CM2G
End Connection : INTERNAL
Material, Housing : SA 516 GR.60
Material, Separator : MONEL
Maximum Operating Pressure : 10.9 KG/CM2 G
Maximum Operating Temprature : 40 DEG C
Service, Fluid : GAS
Size : 388 OD X 150 MM
Type : MESH WIRE
Demister
1200DX150MM,Monel,144.2KG/M3
End Connection : Internal
Material, Housing : SA 516 GR.60
Material, Separator : Monel
Maximum Operating Pressure : 144.2 KG/M3
Maximum Operating Temprature : -18 DEG C
Service, Fluid : GAS
Size : 1200 OD X 150 MM
Type : Mesh Wire
Copper knitted mesh is available for two main materials: one is pure copper, which contains 99% copper and the other is tinned copper, which contains 6% - 8% tin.
The materials are knitted into knitted mesh. The knitted mesh can be mono-filament and multi-filament. The mono-filament is the simplest structure of knitted mesh and the multi-filament knitted mesh has higher strength and can be used in more applications.
There are two types of copper knitted mesh, which are flatten copper knitted mesh and ginning copper knitted mesh. The original knitted mesh is flat, and they can be crimped according to customers' requirements to form ginning copper knitted mesh.
Advantages of copper knitted mesh
High strength.
Firm structure.
Will not scratch or mar.
Never rust.
Non-flammable.
Resistant to disintegration.
Reusable.
Long service life.
Applications of copper knitted mesh
Copper knitted mesh can be used for industrial, for example, copper knitted wire mesh filters is used for cleaning and filtration. Our copper knitted mesh is widely used as air filters, breathers and separators made for cars, trucks and farm equipment.
Copper knitted mesh can be used as knitted wire mesh shielding in cables and other applications.
Copper knitted mesh can be used as filtration materials in oil, gas and water filtration applications.
Copper knitted mesh can be used as knitted copper cleaning mesh for cleaning inside and outside of mechanical parts.
Copper knitted mesh can be made into knitted cleaning balls or scourer to cleaning kitchenware and soldering iron.
Wire mesh demister, or named wire mesh mist eliminator, is a kind of vapor-liquid separating device. It is widely used in chemical industry, petroleum, vitriol, medicine, light industry, metallurgy, machinery, construction, aviation, sea transportation and environmental protection.
Characters:
1.simple structure, light weight;
2.big rate of porosity, small pressure drop;
3.big contact surface, high efficiency of eliminating mist;
4.convenient to install, operate and repair;
5.long life;
The wire mesh used in wire mesh demister has to be made from gas-liquid filter mesh according to working condition.
Mirror defogger, mirror demister
Mirror defogger or mirror demister, offering by bagen under yash brand, which is a thin heating pad for mirror. Mirror defogger is the key part of fog free mirrors, any mirror applied defogger or demister resulted in mirror fog free in bathroom
A demister, or also known as mist eliminator, is a high efficiency separation device often fitted to vapor liquid separator vessels to enhance the removal of liquid droplets entrained in a gas or vapor stream. Demisters may be a mesh type coalescer, vane pack or other structure intended to aggregate the mist into droplets that are heavy enough to separate from the vapor stream.
Mist eliminators/ demisters are fabricated from knitted materials with interlocking asymmetrical loops of metal or plastic with typical diameters being 0.1 – 0.3mm. Special applications for wire diameter 0.35mm to 0.024mm, tube width 1/4" to 42" diameter.
2.DEMISTER Materials:
Stainless Steel wire: 200, 300 and 400 series-AISI201?202?301?302?304?304L?321?316?316L,410S, etc.
Copper wire, Aluminium wire, Nickle wire, Titanium wire, Inconel, Monel, Hastelloy wire...
Plain Steel, Galvanized Steel...
Polypropylene, Polyethylene, PVC, Teflon(PTFE), Nylon, etc.
Stainless steel wire with cotton thread, fiber glass, etc.
3.FIXING METHODS&GRID
The demister should be horizontally fixed and supported. At the bottom or both the top and the bottom, a support grid which is welded with FB 25X3t, RB6Ø of the same material as that of the demister pad at proper intervals (APP150mm), is used. For fixing the grid and the pad, RB6Ø or 1.6Ø tie wire is used.
4.DEMISTER FEATURES (Mesh Pad type)
1).It shows 99% efficiency under general conditions and velocity (1~3m/sec or higher).
2). Over 98% open area is guaranteed under any conditions so pressure drop caused by the use of the demister can be disregarded (0.1”~1.0 W/G).
3). It can be made of any material suitable for the given temperature and corrosion-resistance.
4). It is possible to install by use of M/H so it is easy to handle.
5). There is no restriction in the conditions, place, and size for use. It is install-able on the existing systems.
6). Self-cleaning is possible. It is semi-permanent so it is economical.
5.USE OF DEMISTER
1).Vacuum Tower - The treatment quantity by the demister goes up by 35%. The quality of oil gas is improved.
2). Absorber - Some gasoline plants use a glycol absorber (Demister mounted) so the installation cost is being repaid within a month.
3). Knockout Drums and Separators - If Demister is used, ?inch drum is sufficient.
4). Gas Separator Vessels - Hydrocarbon in gases is collected so gas of 1/0.1 billion purity is produced out.
5). Evaporator - Product loss goes down and purity is remarkably improved.
6). Scrubber - In the field of caustic soda, the demister is used to prevent air pollution.
7). Distillation Column - If Demister is used, the cost for distillation goes up, the quantity of treatment increases by 20%, and purity is remarkably improved.
8). Dust Collectors - The dust collector of a wet type has excellent collection capacity.g is possible. It is semi-permanent so it is economical.
In many leading industries Demister Pads have gained acceptance as a low cost and highly efficient means of separating Entrained liquid droplets from gas and vapour stream and we supply demister pad & mist eliminator for scrubber with high quality, the feathers as blow:
By careful choice of wire diameter, knitted mesh demisters with extremely high free volumes (typically 98-99%) along with very high removal efficiencies and low pressure drop.
Along with wire diameter and mesh density, another important parameter in design and operation is the vapor velocity. This can be controlled by careful selection of the mesh area. Optimal area will depend on operating temperature, pressure and pressure drop. Under normal operating conditions, 99% + removal efficiency can be achieved with a pressure drop of less than 250 Pascals.
Wire Size: 0.08mm - 0.30mm flat wire or round wire. Single-strand knitted, multi-strand knitted, metal & non-metal (various fibers) knitted wires may be pressed into various specification of corrugated wire as require.
Type Specification:
Standard type 40-100 60-150 105-300 140-400 160-400 200-570
High-efficiency type 60-100 80-100 80-150 90-150 150-300 200-400 300-600
High-penetration type 20-100 30-150 70-400 100-600 170-560
Damping type 33-30 38-40 20-40 26-40 30-40 30-50 48-50 30-60 30-80 50-120
or according to your demands
Construction materials:
SUS304, 304L, SUS316, 316L, Copper, Nickel, Titanium, MONEL, P.P (Poly propylene), P.E (poly ethylene), teflon and glass fiber
Packaging Details:
Plastic bag inside, carton or wooden case outside.
Delivery:
10-15 days after received your payments.
Benefits:
1 Easy to install in all process equipment
2 Most cost-effective solution when equipment sizes are set by other requirements
3 High efficiency with low pressure drop
4 Emergency delivery available
5 ISO9001:2008
In many leading industries Demister Pads have gained acceptance as a low cost and highly efficient means of separating Entrained liquid droplets from gas and vapour stream and we supply demister pad & mist eliminator for scrubber with high quality, the feathers as blow:
By careful choice of wire diameter, knitted mesh demisters with extremely high free volumes (typically 98-99%) along with very high removal efficiencies and low pressure drop.
Along with wire diameter and mesh density, another important parameter in design and operation is the vapor velocity. This can be controlled by careful selection of the mesh area. Optimal area will depend on operating temperature, pressure and pressure drop. Under normal operating conditions, 99% + removal efficiency can be achieved with a pressure drop of less than 250 Pascals.
Wire Size: 0.08mm - 0.30mm flat wire or round wire. Single-strand knitted, multi-strand knitted, metal & non-metal (various fibers) knitted wires may be pressed into various specification of corrugated wire as require.
Type Specification:
Standard type 40-100 60-150 105-300 140-400 160-400 200-570
High-efficiency type 60-100 80-100 80-150 90-150 150-300 200-400 300-600
High-penetration type 20-100 30-150 70-400 100-600 170-560
Damping type 33-30 38-40 20-40 26-40 30-40 30-50 48-50 30-60 30-80 50-120
or according to your demands
Construction materials:
SUS304, 304L, SUS316, 316L, Copper, Nickel, Titanium, MONEL, P.P (Poly propylene), P.E (poly ethylene), teflon and glass fiber
Packaging Details:
Plastic bag inside, carton or wooden case outside.
Delivery:
10-15 days after received your payments.
Benefits:
1 Easy to install in all process equipment
2 Most cost-effective solution when equipment sizes are set by other requirements
3 High efficiency with low pressure drop
4 Emergency delivery available
5 ISO9001:2008
