D43Mm Rubber Coated Magnet With M6 Screw Hole Suppliers and Manufacturers

Solid brass with chrome plated one half has m6 304ss pin length 40mm with tapered end 22mm exposed balance inside hinge Other halve has hole for m6 pin, screw holes to be chamfered 4 screws mild steel m6 hex x 8mm long posi drive per hinge (anti vibration screws) Weight :90gms include ss pins

- Solid stainless steel in SS304, SS316, SS316L - Satin Chrome, Satin Stainless Steel, Mirror polished - Standoff,Ø32mm x 20mm, Ø38 x 20MM, Ø38 x 30MM, Ø50 x 20MM, Ø50 x 30MM etc. - 10mm, 12mm glass - Screw rod length as per requirement, screw rod with hex insert if required. - Can supply with hole or without hole.

Waste Specification: European Classification: E46 EWC Code: 19.01.02 Basel Code: B10 10 The material is loose steel scrap processed through an incinerating plant for domestic waste followed by magnetic separation, fragmentized into pieces and consisting partly of tin coated steel cans. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. Due to the scrap dimensions and the material conditions, this particular scrap, should be carefully evaluated first, by the end users, to confirm its adequate recovery ratio and its suitability to be re-melted in the electric arc furnace. Please feel free to contact us for further details

Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.

China Clay: China Clay is a clay mineral with the chemical composition AlSiO3O5(OH)3. It is layered silicate mineral. It is soft earthy, usually white in color, produced by the chemical weathering of Aluminium Silicate mineral like Feldspar. Commercial grades of China Clay are supplied and transported as dry powder form, semi dry noodle form or as slurry. Applications: - It is used in Cer/bamics for body & glazing of Tiles and Sanitary Wares. - In paper it is used as filler. It is also used for paper coating purpose. - It is used in paint also to extend Titanium Dioxide (TiO2) and modify gloss level. - It is used in rubber to enhance reinforcement properties.

Kaolin: Kaolin uses are multiple and diverse. Kaolin are used as functional filler, extender, ceramic raw material and pigment because of its whiteness and fine particle size. Kaolin also hold importance as raw material in refractory applications, concrete, rubber and fiber glass manufacturing. We, as a Kaolin Exporter welcome any size of international orders from Middle East and other countries. Applications: Paper: Kaolin used as a coating pigment and as a filler to replace fiber. It possesses desirable optical properties. Concrete: Kaolin helps to improve strength and durability of concrete. When added to concrete mix, reacts with free lime released during cement hydration to produce additional cementitious material, resulting in an improved high performance concrete. Plastics : Kaolin is widely used as filler in the plastics industry because of its inert chemical nature and its unique size, shape and structure. Agriculture : It is used as a carrier and diluent in fertilizers, pesticides and related products. It is suitable as carrier because it aides the retention of the formulations on the plant. Rubber : It is commonly used as functional filler in rubber applications. While Kaolin improves overall performance for Rubber in general, different types of white pigment play specific roles in rubber application. Paint : Kaolin used as an extender in paints. It reduces the amount of expensive pigment such as Titanium Dioxide. It assists with desirable rheological properties that help maintain proper dispersion and provide bulk to the product. Ceramic : Kaolin improves whiteness and brightness of ceramic body. Good plasticity, good shrinkage, low water absorption and casting rate are also very important properties of kaolin.

METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

Best Cheap Price Meat grinder machine is a meat processing machine with high versatility and wide application scope in the meat products production industry.It is to rely on the screw hopper box in the raw meat pushed to the pre-cut plate ,through the screw rotation extrusion hole plate and reamer generated relative operation ,so as to cut the raw meat into grain shape ,to ensure the uniformity of meat ,through the different combination of hole plate cn achieve the ideal requirements of different meat .Meat process machine meat making machine . Capacity 500-4000kg/hour for different client meat processing needing . Welcome order! good quality good price ! fast delivery

Technical characteristics of SkyLite polycarbonate awning: * Using materials are SkyLite polycarbonate panels with UV resistance, high light transmission, sound insulation, good heat insulation. * Negative link between the frame and the plate, minimizing the screw holes on the surface, avoiding the leak through the screw hole and high aesthetics. Simple to transport and install, save time in construction and installation. * Environmentally friendly, safe for users.

Kaolin also called as China Clay is nearly white in colour. It is distinguished from other industrial clays based on its fine particle size and pure colourings. Its ability to disperse in water makes it an ideal pigment. The primary constituent in kaolin is the mineral kaolinite, a hydrous aluminum silicate formed by the decomposition of minerals such as feldspar. Hydrous kaolin is characterized by its fine particle size, plate like or lamellar particle shape and chemical inertness. APPLICATIONS aints, Coating & Pigments Pharmaceuticals, Cosmetics and Medical Applications Plastics Rubber Ceramics Fibreglass Ultramarine industries Since several years CEMENTATION has been mining, processing and supplying Kaolin products from its reserves in India. Our products offer unique and specific geological characteristics that can be tailor-made to meet the changing demands of the markets that we serve. Our production or supply capacity is more than 150,000 TPA. Our laboratories are well equipped to meet the needs of the diverse markets we serve.

Electro welded wire mesh supply In the forms of rolls or panels, for construction, fences and other industrial uses. It enjoys the feature of corrosion resistance, compared with plain welded wire mesh. Mainly used as fencing panels or further fabricated into wire partitions, wire container panels, wire baskets, welded wire fences, poultry fences and other welded products. Type: Electric Wire Mesh Application: Fence Mesh Hole Shape: Square Wire Gauge: 2.0-4.0mm Processing Service: Bending, Welding, Cutting Product name: welded wire mesh Wire diamter: 0.6-5 mm wire space: 50-300 mm Surface treatment: galvanized, PVC coated Width: 500-1500 mm Length: as request Factory certification: ISO 9001

Inside different weights hexagonal black glue dumbbell for sale Color: Black Materials: all steel and rubber coated Usage: Bodybuilding fitness Weight: 2kg to 50kg Package: OPP bag and packed in Carton box OEM: accept.

Uses: -- Paint -- Plastics -- Rubber -- Putty -- Ceramics -- Chewing gum -- Coating -- Cosmetics -- Cables -- Paper -- Plastics Body powder

Code 17210: Reduced thickness for maximum sensitivity suitable for microsurgery operations Features 1. Triple-layer design consists of double-dipping latex technology and polymer coating. 2. Made by natural rubber latex with low protein content. 3. Excellent hand-fitting made by perfect Color: Brown Hand former: Anatomic shape, non-beaded cuff, textured surface in the grip area, with size embossed Sterility: Sterile Size 6.0, 6.5, 7.0, 7.5, 8.0, 8.5 Overall length: 310 +/- 5mm

Code 18210: Increased thickness for maximum protection suitable for orthopedic surgeries Features 1. Triple-layer design consists of double-dipping latex technology and polymer coating. 2. Made by natural rubber latex with low protein content. 3. Excellent hand-fitting made by perfect Color: Brown Hand former: Anatomic shape, non-beaded cuff, textured surface in the grip area, with size embossed Sterility: Sterile or non-sterile Sizeï¼? 6.0, 6.5, 7.0, 7.5, 8.0, 8.5 Overall length: 310 +/- 5mm

Code 16150: Improved treatment to allow wet hands to slip in easily. Features 1. Triple-layered design consists of double-dipping latex technology and polymer coating. 2. Made by natural rubber latex with low protein content. 3. Excellent hand-fitting made by perfection Color: Natural latex Hand former: Anatomic shape, beaded/non-beaded cuff, textured surface in the grip area, with size embossed Sterility: Sterile Size 6.0, 6.5, 7.0, 7.5, 8.0, 8.5 Overall length: 290 +/- 5mm / or 310+/-5mm

Dolomite mineral is a double carbonate of calcium and magnesium and it exhibits a granular structure. It has high natural whiteness and it's noted for their ease of dispersion. Its use improves properties such as weather ability, reduces shrinkage, fissure development and water absorption. Natural Dolomite Powder is of White Colour and is used as Filler in many applications such as Soap & Detergent, Paints, Ceramics and many other Industries. Applications: - Soap & Detergent Leather Cloth Industry Cable Industries Rigid PVC Pipes Iron, Steel, and Ferro-Alloys Industries Paints, Inks, Powder Coating Ceramic Industry Rubber Industry Glass Industry Available Mesh Size: - 100 TO 700 MESH Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. BRIGHTNESS: - 92 TO 96 AS PER REQUIREMENT Index Compound Result 1. Silica - (SiO2) 10.41 % 2. Alumina - (AI2O3) 01.15 % 3. Iron - (Fe2O3) 00.21 % 4. Titanium - (TiO2) 00.18 % 5. Calcium - (Cao) 30.02 % 6. Magnesium - (MgO) 18.41 % 7. Soda - (Na2O) 00.34 % 8. Potash - (K2O) 00.07 % 9. Loss on Ignition - (LOI) 38.91 %