Description: The PDTHR-150 drill rig is ideal for water well drilling application in rock formation. Thanks to its simple and compact design, excellent performance, high accessibility and reliability at afford cost in its class. The PDTHR-150 rigâ??s flexibility means it can be mounted on Crawler, two truck versions and on local truck matching the rig to the terrain it will be used. Can be used for both DTH and mud rotary drilling. Key features: Proven technology ensures easy maintenance and more productive. The rig can be customize as per customer requirement All the actuators are operated by proportional control valves. Technical specification: Drill rod handling 10 feet (3.0 meter) Drilling depth 500 feet (150 meters) Drilling diameter 4.5 inch (114 mm) - 8 inch (203 mm) Pull up force 5,000 kgf Air compressor 600 cfm/200 psi Mud pump flow 600 lpm - 500 lpm
Product Description: ST-200 model crawler-mounted drilling rig is equipped with BW-250 mud pump. Its triplex mud pump. Have high pressure and large discharge, its adapt to the big diameter and depth holes drilling. The main machine equipped with shift device, fore-and-aft movement by itself, convenient for operate. Main winch and minor winch drive by hydraulic system, they are installed on the main drilling machine. Compact in frame. Its adapted to the wire line coring drilling. The machine is mainly used for water well, wire-line coring drilling, geothermic well, general investigation and exploration. Road and tall building ground drill exploration and other foundation working.
Crawler Mounted Hydraulic DTH Drilling Rig Automatic Crawler Mounted DTH Drill Rig, Crawler Mounted Drilling Rigs Advanced Technology, easy to handle and operate. Borehole Diameter 105ï½?305mm Site Condition CM458 is applicable to all kinds of anchor supporting operation, grouting hole drilling for cofferdam, dam, and base reinforcement. Newly designed hydraulic clamp makes operation easier. Product Features CM458 internal combustion (CM458D Electric) crawler mounted versatile anchor rig adopts diesel engine and hydraulic oil pump assemblies to provide power, allowing rigs to finish moving, rotating, propelling and lifting, as well as angle positioning. During drillingï¼?only the percussive hammer consumes compressed air. CM458 is applicable to all kinds of anchor supporting operation. In addition, the rig is also applicable to the grouting hole drilling for cofferdam, dam, and base reinforcement. Newly designed hydraulic clamp is a very useful device making operation easier. Model CM458 Borehole diameter 105-305mm Borehole depth 200m Applicable rock hardness f=6-20 Working air pressure 1.2-3.5MPa Air consumption 16-40m/min Feeding stroke 3300mm Rod-changing length 3m Ground clearance 254mm Rotation rate 0-50rpm Rotation torque 5400Nm Travle speed 2Km/h Grade ability 24° Power Yuchai 70KW/Cummins 74KW Electric motor 45KW Dust collector (optional) Hydraulic dry dust collector Wet dust collector Dimension (LxWxH) 6900mmÃ?2200mmÃ?2200mm Weight 6200kg
Crawler Mounted Versatile Well Drilling Rig hydraulic drill rig, Automatic Crawler Mounted DTH Drill Rig A new, efficient, and versatile hydraulic percussive well rig Rated Drilling Depth 500m Site Condition It is mainly applicable to the drilling process of wells, monitor boreholes and geothermal boreholes. Product Features JKS500C Crawler Mounted Versatile Well Drilling Rig is a new, efficient and multifunctional drill rig, mainly applicable to all kinds of drilling process of wells, monitor boreholes, geothermal boreholes, grouting holes of cofferdam, dam and reinforced base, as well as long hole drilling of open pit, anchor reinforcement and defense project. The rig equips with powerful hydraulic motor, heavy-duty hydraulic drilling arm and high pressure DTH percussive hammer, and its drilling speed is faster than other type of rigs. We are Crawler Mounted Drill Rig Supplier and Crawler Mounted Drill Rig Factory Rated Drilling Depth 500m Drilling Diameter 105-350mm Working Air Pressure 1.05-4.5MPa Air Consumption 16-60m³/min Drilling Rod Diameter Ï?89mm, Ï?102mm, Ï?114mm Max. Lifting Force 25T Axial Pressure ±10T Lifting Force of Small Winch 1.5T Lifting Force of Main Winch 4T (optional) Rotation Torque 9500N.m Rotation Rate 0-40/80rpm Feeding Force 3800mm Lifting Rate 0-18m/min Grade Ability 15° Hydraulic Motor 24kW/380V (optional) Flow of Foam Pump 20L/min (optional) Dimension (L x W x H) 6800mm x 2250mm x 2650mm
Hydraulic Drilling Rig Features JK590C / JK590 are the new generation of diesel (electric) crawler mounted hydraulic DTH drilling rig, the latest updated version of JK590 series. In contrast with the last generation, they feature lower operation cost and humanized design. They adopt a 70kW Yuchai diesel engine and hydraulic pump station assembly to generate power to rotate, feed, lift, walk and angle position. During operation, only the percussive hammer consumes the compressed air. In contrast with conventional pneumatic drill rigs, JK590C/JK590 crawler drilling rig consume about 40% to 50% less energy (diesel or electricity), and the air displacement of matched air compressor decreases 30% to 50%. Compared with JK590, JK590C is additionally equipped with hydraulic dust collection system, and wet type dust collector is optional if water is accessible on site. JK590C/JK590 are mainly applicable to blast hole drilling process of hydropower construction, open pit mining, quarrying, road construction and national defense construction. Hydraulic Drilling Rig Technical Parameters Model JK590 Borehole diameter 90-165mm Borehole depth 50m Applicable rock hardness f=6-20 Working air pressure 1.2-2.4MPa Air consumption 11-21m³/min Feeding stroke 4138mm Rod-changing length 3m Max. horizontal drilling height 3370 Rotation rate 0-80rpm Rotation torque 3000Nm Walking speed 2Km/h, 3Km/h Grade ability 24° Power Yuchai 70KW/Cummins 74KW (optional) Electric motor 45KW Dust collector (optional) Hydraulic dry dust collector Wet dust collector Dimension (LxWxH) 7000mm x 2200mm x 2100mm Weight 6500kg The crawler drilling rigs are widely used in blasthole drilling of mining, hydropower, transportation and defense projects, as well as harbor and channel construction; The hydraulic drilling rigs are specialized in drilling the boreholes of large diameter and depth, for instance, water well drilling and geothermal well drilling.
Well Drilling Equipment Features JKS300B Well Drilling Equipment is a new type of efficient and versatile hydraulic rig. It is mainly applicable to the drilling process of water wells, monitor wells, and geothermal wells. When drilling in the rock layer, the rig adopts DTH hammer for penetration and compressed air for cleaning, with a penetration speed being dozens of times quicker than conventional rotation rigs. In loose rock, the rig employs a cutting bit or cone bit and uses mud to clean the dirt, its versatility suiting for all kinds of complex geological conditions. Winch can lift stuff upwards of 6m, facilitating installing pipes. Hydraulic supporters facilitate the rig erection on site without crane. Smaller size makes it adaptable to various kinds of construction sites. Well Drilling Equipment Parameters Rated Drilling Depth 300m Borehole Diameter 105-350mm Engine Power 92kW Maximum Lifting Force 15T Small Winch Lifting Force 1.5T Rotation Torque 8500N.m Rotation Rate 0-40/80rpm Feeding Stroke 3600mm Lifting Speed 0-18m/min Grade Ability 15° Hydraulic Generator (optional) 24kW/380V Flow of Foam Pump (optional) 20L/min Dimension (L x W x H) 6300mm x 2000mm x 2300mm Working Size (W x H) 3100mm x 6900mm Weight 8.5T
Description: The PCDR-1000 drill rig is ideal for exploration drilling application in rock formation. Thanks to its simple and compact design, excellent performance, high accessibility and reliability at afford cost in its class. The PCDR-1000 rigâ??s flexibility means it can be mounted on single truck version, crawler mounted versions and on local truck matching the rig to the terrain it will be used. Optional: Multipurpose drill rig (Core, DTH, mud rotary) Key features: Proven technology ensures easy maintenance and more productive. The rig can be customize as per customer requirement. Key specification: Drill rod handling 20 feet (6.0 meter) Drilling depth up to 3330 feet (1000 meters) Drilling diameter NQ-HQ Pull up force 17,000 kgf Drill head torque 85 kg.m â?? 700 kg.m Gear Box Dual speed gearbox Angle Drilling 45 Deg Carrier Truck(Optional: Crawler) Optional Tractor/Skid/Trolley
Crawler Mounted Hydraulic DTH Drilling Rig Crawler Mounted DTH Drill Rig, Crawler Mounted Drilling Rigs Low operation cost and humanized design. Borehole Diameter 90-165mm Site Condition It is applicable to the blast hole drilling process of hydro project, open pit mining, quarrying, road construction and defense project. Product Features JK590C / JK590 are the new generation of internal combustion (electric) crawler mounted hydraulic DTH drilling rig, the latest updated version of JK590 series. In contrast with the last generation, they feature lower operation cost and humanized design. They adopt a 70kW Yuchai diesel engine and hydraulic oil pump station assembly to generate power, allowing rigs to rotation, propelling, lifting, walking and angle positioning. During operation, only the percussive hammer consumes the compressed air. In contrast with conventional pneumatic drill rigs, JK590C/JK590 consume about 40% to 50% less energy (oil or electricity), and the air displacement of matched air compressor decreases 30% to 50%. Compared with JK590, JK590C is additionally equipped with dust collection system, and wet type dust collector is optional once water is accessible on site. JK590C/JK590 are mainly applicable to blasting borehole drilling process of hydro project, open pit mining, quarrying, road construction and defense project. Model JK590 Borehole diameter 90-165mm Borehole depth 50m Applicable rock hardness f=6-20 Working air pressure 1.2-2.4MPa Air consumption 11-21m³/min Feeding stroke 4138mm Rod-changing length 3m Max. horizontal drilling height 3370 Rotation rate 0-80rpm Rotation torque 3000Nm Travle speed 2Km/h, 3Km/h Grade ability 24° Power Yuchai 70KW/Cummins 74KW (optional) Electric motor 45KW Dust collector (optional) Hydraulic dry dust collector Wet dust collector Dimension (LxWxH) 7000mm x 2200mm x 2100mm Weight 6500kg
JK520 Crawler Mounted Hydraulic DTH Drilling Rig Crawler Mounted Hydraulic DTH Drilling Rig Crawler Mounted Drilling Rigs, Crawler Mounted DTH Drill Rig It features its compact design, small footprint, and humanized operation. Borehole Diameter 90-150mm Site Condition It is applicable to the blasting borehole drilling process of hydro project, open pit mining and road construction. Product Features JK520 internal combustion (electric) crawler mounted hydraulic DTH drilling rig is the latest updated product of the "Sharp Sword" series, specially designed for the hydropower project and quarry mining project. JK520 can drill boreholes of various angles, ranging from horizontal angle to vertical angle. It boasts its better performance, compact design, small footprint and humanized operation. JK520 is equipped with environment-friendly dry type dust collector, and as long as water is accessible on working site, wet type dust collector is optional. Model JK520 Borehole diameter 90-150mm Borehole depth 40m Applicable rock hardness f=6-20 Working air pressure 1.2-2.4MPa Air consumption 11-21m³/min Feeding stroke 3865mm Rod-changing length 3m Max. horizontal drilling height 2510mm Feed extension 1200mm Ground clearance 300mm Rotation rate 0-79rpm Rotation torque 2500Nm Travle speed 2Km/h, 3Km/h Grade ability 25° Power Yuchai 70KW Dust collector (optional) Hydraulic dry dust collector Wet dust collector Dimension (LxWxH) 7000mmÃ?2250mmÃ?2250mm Weight 5800kg Wired remote control Optional
MODEL C370R BLASTHOLE DRILL SPECIFICATIONS RATED CAPACITY : Nominal hole size 10 5/8” (270 mm) to 12 ¼” (311 mm)dia by Rotary method . Total depth capacity: 160’ with 40’ long drill pipe STANDARD MOUNTING : CAT USA, 200mm Triple grouser track long with 13 bottom rollers and 3 carrier rollers each side. Independent hydraulic motor with Planetary gearbox drive for each track. Propel speed is 1.6 KMPH on plain grounds and 0.8 KMPH on Gradients. Gradeability upto 25% grades with Mast down. PULLDOWN AND HOIST : Pulldown is achieved through twin hydraulic cylinders and roller chain arrangement. 43’ head travel for handling 40’ long drill pipe. Bit Loading : 80,000 LBS. Hoisting capacity : 33,000 LBS. Standard feed rate : 12 FPM Standard hoist rate : 25 FPM Fast feed rate : 80 FPM Fast hoist rate : 170 FPM MAST : Electrically welded square and rectangular steel tube construction to withstand adverse drilling conditions. Mast is raised and lowered by two hydraulic cylinders with safety check valves. Working height of mast 52’ 2” for 40’ long drill pipe. ROTARY HEAD : Axial piston hydraulic motors driven top head drive through Planetary gearbox and spur gear reduction with a constant torque of 1,08,000 Inch-pounds at 0 - 150 RPM infinitely variable speed. AIR COMPRESSOR : Screw compressor with a capacity of 1880 CFM at 100 PSI. PRIME MOVER : CAT USA make Diesel engine model C23 or Cummins Make QSK23 800 H.P running @ 1800 RPM and drives Screw compressor from the flywheel and a set of Hydraulic pumps from the front PTO. Emission norms as per EPA TIER III. Fuel tank capacity: 1000 Lits DRILL PIPE HANDLING : Hydraulically operated 4 pod loader suitable for handling 10 ¾” dia , 40’ long drill pipe Hydraulic power breakout system and stem wrench are provided as standard. LEVELLING JACKS : Three hydraulic jacks – one front 200mm bore, 48” stroke and two rear 160mm bore, 48” stroke equipped with heavy duty telescopic guide tubes and lock check valves for safety. OPERATOR’S CAB : Fully enclosed steel fabricated, sound suppressed to 85dB, spacious, Double panelled and safety glassed cab with centralised Electric “Joy stick” controls for operator’s convenience. Adjustable seat for operator’s comfort and a seat for helper DUST CONTROL SYSTEM : NVE type dust control system, equipped with hydraulic motor driven suction blower and dry type filter cartridges. HYDRAULIC SYSTEM : Open loop hydraulic system for propel, rotation, feed, fan and auxiliary circuits. Axial piston, variable volume pumps - 2 no’s, 58 GPM each at 4000 PSI for Tram/Rotation circuit. Axial piston variable volume pump 18 GPM at 3000 PSI for feed circuit. Tandem gear pump 64 GPM at 3500 PSI for ROC fan circuit and 26 GPM at 2000 PSI for auxiliary circuit. Hydraulic oil reservoir with suction strainers and 10 micron return line filters and pressure filter for pilot line. Relief valves in all circuits. POWER BREAKOUT : Hydraulically operated Power Breakout system for easy removal of drill pipes. NIGHT LIGHTING : Adequate lighting to enable operation of drill at night times. Lights suitable for 24V, DC supply. ANGLE HOLE DRILLING : Angle hole drilling kit upto 25 in steps of 5. WINCH : Hydraulic winch is provided for handling accessories. ACCESSORIES : Four nos of Drillpipes, Two nos Spindle subs and one no each of Bitsub, Hammersub,Bit breakout baskets are supplied. OPTIONAL EQUIPMENT : Centralised Lubrication system Water injection system with water tank Shocksub for rotary head Rotary Deck Bushing Electronic depth counter Automatic Power breakout system Fire detection and suppression system Fast fuelling system.
MODEL C650D-EXP BLASTHOLE DRILL SPECIFICATIONS RATED CAPACITY : Nominal hole size 7-7/8¡¨(200 mm ) by Rotary method, Upto a depth of 148¡¦ (45.12 m) using 30¡¦ long 6.25¡¨ OD drill pipes. STANDARD MOUNTING : Tengl, India make Under Carriage model T23/D4 , 24¡¨ Triple grouser track 10¡¦ 6¡¨ long with 9 bottom rollers and 2 carrier rollers each side. Independent hydraulic motor with Planetary gearbox drive for each track. Propel speed is 3.0 KMPH on plains and 1.5 KMPH on grades. Gradeability up to 25% grades with Mast down. PULLDOWN AND HOIST : Pulldown is achieved through twin hydraulic cylinders and roller chain arrangement. 33¡¦ head travel for handling 30¡¦ long drill pipe. Pulldown capacity : 35,000 LBS. Hoisting capacity : 20,000 LBS. Standard feed rate : 14 FPM Standard hoist rate : 25 FPM Fast feed rate : 70 FPM Fast hoist rate : 124 FPM MAST :Electrically welded square and rectangular steel mast of robust construction to withstand adverse drilling conditions. Mast is raised and lowered by two hydraulic cylinders with safety check valves. Working height of mast 38¡¦ for 30¡¦ long drill pipe. ROTARY HEAD :Axial piston hydraulic motor driven top head drive through spur gear reduction with a constant torque of 48,000 Inch-pounds at 0-150 RPM infinitely variable speed. AIR COMPRESSOR :Screw compressor with a capacity of 900 CFM at 100 PSI. Air oil receiver, Oil cooler, Oil filters and safety valves are provided as standard. PRIME MOVER : Cummins India make engine NTA 855C running @ 1800 RPM drives compressor @ flywheel end and hyd. pumps @ front PTO. Fuel tank capacity : 750 lit. DRILL PIPE HANDLING : Hydraulically operated Four pod loader suitable for handling 6.25¡¨ OD x 30¡¦ long drill Hydraulic power breakout wrench and stem wrench are provided as standard. HYDRAULIC SYSTEM : Open loop hydraulic system for propel, rotation, feed, Fan, auxiliary and pilot circuits. Axial piston ,variable volume pump: 48 US GPM at 4700 PSI for tram circuit and at 4200 PSI for rotation circuit. Axial piston pump : 12 US GPM at 2500 PSI for feed circuit. Gear pump for ROC fan : 22 US GPM at 3000 PSI for ROC fan circuit and 15 US GPM at 2000 PSI for auxiliary circuit. Hydraulic oil reservoir with suction strainers and 10 micron return line filters. Relief valves in all circuits. LEVELLING JACKS : Three hydraulic jacks - one front 140 MM bore, 48¡¨ stroke; two rear 125 MM bore, 36¡¨ stroke equipped with heavyduty telescopic guide tubes and lock check valves for safety. OPERATOR¡¦S CAB :Fully enclosed spacious steel fabricated, sound suppressed, thermal insulated, Air-conditioned and safety glassed cab with centralised controls for operator¡¦s convenience. Adjustable seat for operator¡¦s comfort and a seat for Helper. DUST CONTROL SYSTEM : NVE type dust control system, equipped with hydraulic motor driven blower and dry type filters. NIGHT LIGHTING : Adequate lighting to enable operation of drill at night times. Lights powered by engine alternator at 24V, DC supply. WEIGHT AND DIMENSIONS :(Approx.) Length(mast down) : 43¡¦ 0¡¨ Length(mast up) : 32¡¦ 0¡¨ Width : 14¡¦ 2¡¨ Height(mast down) : 16¡¦ 0¡¨ Height(mast up) : 42¡¦ 6¡¨ Operating Weight : 73,500 LBS OPTIONAL EQUIPMENT: Centralised Lubrication system Shock sub for rotary head Rotary Deck Bushing Hyd powered winch Electronic depth counter Automatic Power breakout system Fire detection and suppression system Fast fuelling system Retractable dust curtain Water injection system with water tank Angle hole drilling kit upto 25„a in steps of 5„a. 122
Model : C650D-EXP blasthole drill Specifications: Rated capacity : Nominal hole size 7-7/8(200 mm ) by Rotary method, Upto a depth of 148 (45.12 m) using 30 long 6.25 OD drill pipes. Standard mounting : Tengl, India make Under Carriage model T23/D4 , 24 Triple grouser track 10 6 long with 9 bottom rollers and 2 carrier rollers each side. Independent hydraulic motor with Planetary gearbox drive for each track. Propel speed is 3.0 KMPH on plains and 1.5 KMPH on grades. Gradeability up to 25% grades with Mast down. Pulldown and hoist :Pulldown is achieved through twin hydraulic cylinders and roller chain arrangement. 33 head travel for handling 30 long drill pipe. Pulldown capacity: 35,000 LBS. Hoisting capacity: 20,000 LBS. Standard feed rate: 14 FPM Standard hoist rate: 25 FPM Fast feed rate: 70 FPM Fast hoist rate : 124 FPM MAST : Electrically welded square and rectangular steel mast of robust construction to withstand adverse drilling conditions. Mast is raised and lowered by two hydraulic cylinders with safety check valves. Working height of mast 38 for 30 long drill pipe. ROTARY HEAD : Axial piston hydraulic motor driven top head drive through spur gear reduction with a constant torque of 48,000 Inch-pounds at 0-150 RPM infinitely variable speed. AIR COMPRESSOR: Screw compressor with a capacity of 900 CFM at 100 PSI. Air oil receiver, Oil cooler, Oil filters and safety valves are provided as standard. PRIME MOVER: Cummins India make engine NTA 855C running @ 1800 RPM drives compressor @ flywheel end and hyd. pumps @ front PTO. Fuel tank capacity : 750 lit. DRILL PIPE HANDLING: Hydraulically operated Four pod loader suitable for handling 6.25 OD x 30 long drill Hydraulic power breakout wrench and stem wrench are provided as standard. HYDRAULIC SYSTEM : Open loop hydraulic system for propel, rotation, feed, Fan, auxiliary and pilot circuits. Axial piston ,variable volume pump: 48 US GPM at 4700 PSI for tram circuit and at 4200 PSI for rotation circuit. Axial piston pump : 12 US GPM at 2500 PSI for feed circuit. Gear pump for ROC fan : 22 US GPM at 3000 PSI for ROC fan circuit and 15 US GPM at 2000 PSI for auxiliary circuit. Hydraulic oil reservoir with suction strainers and 10 micron return line filters. Relief valves in all circuits. LEVELLING JACKS : Three hydraulic jacks - one front 140 MM bore, 48 stroke; two rear 125 MM bore, 36 stroke equipped with heavyduty telescopic guide tubes and lock check valves for safety. OPTIONAL EQUIPMENT: Centralised Lubrication system Shock sub for rotary head Rotary Deck Bushing Hyd powered winch Electronic depth counter Automatic Power breakout system Fire detection and suppression system Fast fuelling system Retractable dust curtain Water injection system with water tank.
Crawler Mounted Versatile Well Drilling Rig Truck Mounted Well Drilling Rig Its smaller size can be adapted to various construction sites. Rated Drilling Depth 300m Application JKS300B Crawler Mounted Versatile Well Drilling Rig is applicable to the drilling process of water wells, monitor wells and geothermal wells, etc. Product Features JKS300B Crawler Mounted Versatile Well Drilling Rig is a new type of efficient and versatile hydraulic rig. It is mainly applicable to the drilling process of water wells, monitor wells, and geothermal wells. When drilling in the rock layer, the rig adopts DTH hammer for penetration and compressed air for cleaning, with a penetration speed being dozens of times quicker than conventional rotation rigs. In loose rock, the rig employs a cutting bit or cone bit and uses mud to clean the dirt, its versatility suiting for all kinds of complex geological conditions. Winch can lift stuff upwards of 6m, facilitating installing pipes. Hydraulic supporters facilitate the rig erection on site without crane. Smaller size makes it adaptable to various kinds of construction sites. We also provide Truck Mounted Well Drilling Rig ,Airman Air Compressor,Hydraulic Crawler Drills and soon Rated Drilling Depth 300m Borehole Diameter 105-350mm Engine Power 92kW Maximum Lifting Force 15T Small Winch Lifting Force 1.5T Rotation Torque 8500N.m Rotation Rate 0-40/80rpm
Crawler Mounted Versatile Well Drilling Rig Truck Mounted Well Drilling Rig Its smaller size can be adapted to various construction sites. Rated Drilling Depth 300m Application It is applicable to the drilling process of water wells, monitor wells and geothermal wells, etc. Product Features JKS300B crawler mounted versatile well drilling rig is a new type of efficient and versatile hydraulic rig. It is mainly applicable to the drilling process of water wells, monitor wells, and geothermal wells. When drilling in the rock layer, the rig adopts DTH hammer for penetration and compressed air for cleaning, with a penetration speed being dozens of times quicker than conventional rotation rigs. In loose rock, the rig employs a cutting bit or cone bit and uses mud to clean the dirt, its versatility suiting for all kinds of complex geological conditions. Winch can lift stuff upwards of 6m, facilitating installing pipes. Hydraulic supporters facilitate the rig erection on site without crane. Smaller size makes it adaptable to various kinds of construction sites. Rated Drilling Depth 300m Borehole Diameter 105-350mm Engine Power 92kW Maximum Lifting Force 15T Small Winch Lifting Force 1.5T Rotation Torque 8500N.m Rotation Rate 0-40/80rpm Feeding Stroke 3600mm Lifting Speed 0-18m/min Grade Ability 15° Hydraulic Generator (optional) 24kW/380V Flow of Foam Pump (optional) 20L/min Dimension (L x W x H) 6300mm x 2000mm x 2300mm Working Size (W x H) 3100mm x 6900mm Weight 8.5T
Truck Mounted Well Drilling Rig Features JKCS300 truck mounted versatile well drilling rig is a new, efficient and multifunctional hydraulic rig, mainly applicable to all kinds of drilling process of wells, monitor boreholes, geothermal boreholes, and grouting holes of cofferdam, dam and reinforced base, as well as drilling of open pit mining, anchor reinforcement project and defense project. The rig equips with powerful hydraulic motor, heavy hydraulic drilling arm and high pressure DTH percussive hammer, and its drilling speed is faster than other type of rigs. Truck Mounted Drilling Rig parameters Specifications of JKCS300 Versatile Well Drilling Rig Borehole Diameter Ï?105-350mm Borehole Drilling Depth 300m Working Air Pressure 1.05-3.05MPa Air Consumption 16-35m³/min Rod Diameter Ï?89mm, Ï?102mm, Ï?114mm Rod Length 3m / 4.5m Grade Ability 15° Winch System ( standard main winch & optional tooling winch) Lifting Force 15t Lifting Height 8m Feed System Axial Pressure ±6t Rotation Torque 4500N.m 8500N.m Rotation Rate 0-80rpm 0-160rpm Weight 8t (excluding vehicle) Dimension (L x W x H) 10500mm x 2480mm x 3050mm (transport) Working Size (L x W x H) 11000mm x 2480mm x 7147mm If you are finding Truck Mounted Drilling Rig Factory, we will be your best choose! We are dedicated to providing our customers with high quality and hightech products.
JKCS300 Truck Mounted Well Drilling Rig Truck Mounted Well Drilling Rig Truck Mounted Water Well Drilling Rig A new, efficient and versatile well drilling rig Rated Drilling Depth 300m Site Condition It is mainly applicable to the drilling process of wells, monitor boreholes, geothermal boreholes and grouting borehole of cofferdam. Product Features JKCS300 truck mounted versatile well drilling rig is a new, efficient and multifunctional hydraulic rig, mainly applicable to all kinds of drilling process of wells, monitor boreholes, geothermal boreholes, and grouting holes of cofferdam, dam and reinforced base, as well as drilling of open pit mining, anchor reinforcement project and defense project. The rig equips with powerful hydraulic motor, heavy hydraulic drilling arm and high pressure DTH percussive hammer, and its drilling speed is faster than other type of rigs. Specifications of JKCS300 Versatile Well Drilling Rig Borehole Diameter Ï?105-350mm Borehole Drilling Depth 300m Working Air Pressure 1.05-3.05MPa Air Consumption 16-35m³/min Rod Diameter Ï?89mm, Ï?102mm, Ï?114mm Rod Length 3m / 4.5m Grade Ability 15° Winch System ( standard main winch & optional tooling winch) Lifting Force 15t Lifting Height 8m Feed System Axial Pressure ±6t Rotation Torque 4500N.m 8500N.m Rotation Rate 0-80rpm 0-160rpm
Crawler Mounted Hydraulic DTH Drilling Rig Crawler Mounted DTH Drill Rig, Hydraulic Crawler Drills In contrast to the pneumatic drilling rig, energy consumption (diesel or electricity) saves about 40% to 50%. Borehole Diameter 90-165mm Site Condition CM358A crawler mounted hydraulic DTHdrilling rig is mainly applicable to the blast hole drilling process of open pit mining, quarrying, hydropower project and road constructions. Product Features CM358A crawler mounted hydraulic DTHdrilling rig adopts diesel engine (or electric motor) and hydraulic oil pump assembly to provide power, allowing rigs to finish moving, rotating, feeding and lifting, as well as angle positioning. During operation only the percussive DTH rigs consumes compressed air and in contrast to the conventional pneumatic rigs, CM358A saves about 40%~50% of total energy. More information you can views here We also provide Tophammer Drilling Rigs ,Water Well Drill Rig ,Truck Mounted DTH Drilling Rig
New, efficient and versatile hydraulic drill rig Rated Drilling Depth 400m Site Condition JKS400B Crawler Mounted Versatile Well Drilling Rig is mainly applicable to the drilling process of wells, monitor boreholes and geothermal boreholes. Product Features JKS400B Crawler Mounted Versatile Well Drilling Rig is a new efficient and multifunctional drill rig, mainly applicable to the drilling process of well, monitor boreholes and geothermal boreholes. When drilling in the rock layer, the rig adopts DTH percussive hammer for penetration and compressed air for cleaning, the penetration speed being dozens of times quicker than conventional rotation rigs. In loose rock, the rig employs a cutting bit or cone bit and uses mud to clean the dirt, its versatility suiting for all kinds of complex geological conditions Winch can lift stuff upwards of 6m, facilitating installing pipes. Hydraulic supporters facilitate the rig erection on site without crane. We are Crawler Mounted Drill Rig Supplier and Crawler Mounted Drill Rig Factory Dimension (L x W x H) 6800mm x 2250mm x 2650mm Working Size (W x H) 3250mm x 7500mm Weight 10.5T Rated Drilling Depth 400m Borehole Diameter 105ï½?350mm Engine Power 92kW Max. Lifting Force 20T Small Winch Lifting Force 1.5T Rotation Torque 9000N.m Rotation Rate 0ï½?40/80rpm Feeding Stroke 3800mm Lifting Speed 0ï½?18m/min Centralizer Height 0.7m Grade Ability 15° Hydraulic Generator (optional) 24kW/380V Flow of Foam Pump (optional) 20L/min
Crawler Mounted Hydraulic DTH Drilling Rig Crawler Mounted DTH Drill Rig, Hydraulic Crawler Drills In contrast to the pneumatic drilling rig, energy consumption (diesel or electricity) saves about 40% to 50%. Borehole Diameter 90-165mm Site Condition CM358A crawler mounted hydraulic DTH drilling rig is mainly applicable to the blast hole drilling process of open pit mining, quarrying, hydropower project and road constructions. Product Features CM358A crawler mounted hydraulic DTH drilling rig adopts diesel engine (or electric motor) and hydraulic oil pump assembly to provide power, allowing rigs to finish moving, rotating, feeding and lifting, as well as angle positioning. During operation only the percussive DTH rigs consumes compressed air and in contrast to the conventional pneumatic rigs, CM358A saves about 40%~50% of total energy. Model CM358A Borehole diameter 90-165mm Borehole depth 50m Applicable rock hardness f=6-20 Working air pressure 1.2-2.4MPa Air consumption 11-21m³/min Feeding stroke 3820mm Rod-changing length 3m Max. horizontal drilling height 3370mm Rotation rate 0-80rpm Rotation torque 3000Nm Travel speed 2Km/h Grade ability 24° Power Yuchai 70KW/Cummins 74KW Electric motor 45KW Dust collector (optional) Hydraulic dry dust collector Wet dust collector Dimension (LxWxH) 6900mm Ã? 2200mm Ã? 2200mm Weight 6100kg
JKS400SH Crawler Mounted Telescoping Mast Drill Rig Crawler Mounted Versatile Well Drilling Rig hydraulic drilling rig, hydraulic drill rig The rig is able to place casing of 6 meters. Rated Drilling Depth 400m Site Condition It is mainly applicable to the drilling process of wells, monitor boreholes and geothermal boreholes. Product Features JKS400SH crawler mounted telescoping mast drill rig is a new, efficient, multifunctional hydraulic well drilling rig, mainly applicable to the drilling process of well, monitor boreholes and geothermal boreholes. When drilling in the rock layer, the rig adopts DTH percussive hammer for penetration and compressed air for cleaning, the penetration speed being dozens of times quicker than conventional rotation rigs. The rig is able to handle casing size up to 6 meters. In loose rock, the rig employs a cutting bit or cone bit and uses mud to clean the dirt, its versatility suiting for all kinds of complex geological conditions Hydraulic supporters used facilitate the rig erection on site without crane. Rated Drilling Depth 400m Borehole Diameter 140~350mm Engine Power 92kW Max. Lifting Force 20T Axial Pressure ± 8T Lifting Force of Small Winch 1.5T Rotation Torque 8500N.m Rotation Rate 0ï½?40/80rpm Feeding Stroke 4300mm+2600mm Hydraulic Supporting Leg Stroke 1650mm Lifting Speed 0ï½?25m/min Centralizer Height 0.8m Grade Ability 15° Dimension (L x W x H) 7.4m x 2.25m x 2.85m Weight 13.5T Hydraulic Generator 24kW/380V (optional) Flow of Centrifugal Mud Pump / Flow of Plunger Mud Pump /
