Cm10N Portable Metal Coating Thickness Gauge Suppliers and Manufacturers

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

1> Back To Back Towel Bars(with and without metal washers) 2> Pull handled available in various sizes with back to back Towel bars 3> Glass thickness : 6 mm~12 mm 4> Size: 19 x 6"/8"/10/12"/18"/24" C/C 5> Material :304 Stainless Steel / #62 Brass Tubular 6> Chrome plated, Brushed Nickel, Brass Polished, Polished Chrome, Gold Plated, Oil Rubbed Bronze.

Focus-6200 products are kind of non-hardening and self-adhesive waterproof sealing butyl tapes. The materials are weathering resistance and fully accommodate to the surface that it attached to, with effective life up to 20 years. Main Specification (Customized size is acceptable.) 2mm thickness * 20mm width * 20mm roll length 2mm thickness * 30mm width *20mm roll length Main Color - black, grey, white Technical Data Product Series FOCUS-6200 Series Application Construction Industry Elongation - 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 25N/cm Tensile Strength 250KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet Advantages * Never hardening, maintain good waterproofing property with weathering resistance performance. * Excellent performance in waterproofing and sealing. * Good anti-aging performance effective life up to 20years. * Easy to apply. Applications * Provide waterproof and sealing protection forsteel structure construction. * Provide waterproof and sealing protection for door joints, window joints,roofs and air-ducts. Provide waterproof and sealing protection for sunshine rooms, light plate rooms and thermostatic chamber. * Provide repair function for leaks on surfaces of metal/plastic/glass/concrete.

Chickpeas also known as Black Chana was first grown in Australia as a commercial crop in Goondiwindi during the early 1970s. It is now an important crop in northern farming systems (NSW and Queensland) and becoming more widely grown in southern (Victoria and South Australia) and western (Western Australia) regions. Also known as Bengal gram, Black Chana grain is exceptionally high in protein and has a low glycemic index making it an excellent protein for people with Diabetes. Black Chana, are light to dark brown colour. They are in the 6 to 7mm range, with a thick seed coat. Desi Chickpeas produced are split in half to make Chana Dahl, this split form are ground into flour called Besan.

NOVEXIM Dear all customer Produced from freshly selected matured coconuts, Desiccated Coconut Low Fat is the dehydrated white coconut meat with lower fat content. Our products are unsweetened and do not contain any preservatives or additives. Desiccated Coconut Low Fat is most ideal for confectioneries and used as fillings, toppings and as ingredients especially for food manufacturers. Desiccated Coconut Low Fat is perfect for various industries that require the exhilarating feel of natural fibre in the product. As the product is more shelf stable compared to Desiccated Coconut High Fat, our Desiccated Coconut Low Fat is a good substitute for Desiccated Coconut High Fat. Bakeries Popularly used as topping for cakes and pastries; centre filling for buns; decoration for cakes; etc. Confectioneries â?? Very ideal as fillings for candy bars; chocolate coating, etc. Desiccated Coconut Low Fat should be stored in a clean, cool and dry place away from direct sunlight, chemicals and free from odors, under an ideal room temperature of between 26C to 3C. Ingredient Fresh Coconut Meat Oil : 60 - 65 % Color Natural white Appearance Free from insect infestation, foreign bodies and metal. Flavour Mild, fresh and sweet characteristics of coconut with no off-flavour or odour Packing In 3-ply Kraft paper bags with inner sealed polyliner Size of Packing 25 kg net per bag Qty Per 20ft FCL 280 bags x 25 kg net (7 metric tons) Qty Per 40â?? HC 560 bags x 25 kg net ( 14 metric tons)

NOVEXIM Dear all customer Produced from freshly selected matured coconuts, Desiccated Coconut Low Fat is the dehydrated white coconut meat with lower fat content. Our products are unsweetened and do not contain any preservatives or additives. Desiccated Coconut Low Fat is most ideal for confectioneries and used as fillings, toppings and as ingredients especially for food manufacturers. Desiccated Coconut Low Fat is perfect for various industries that require the exhilarating feel of natural fibre in the product. As the product is more shelf stable compared to Desiccated Coconut High Fat, our Desiccated Coconut Low Fat is a good substitute for Desiccated Coconut High Fat. Bakeries Popularly used as topping for cakes and pastries; centre filling for buns; decoration for cakes; etc. Confectioneries Very ideal as fillings for candy bars; chocolate coating, etc. Desiccated Coconut Low Fat should be stored in a clean, cool and dry place away from direct sunlight, chemicals and free from odors, under an ideal room temperature of between 26C to 32C. Ingredient Fresh Coconut Meat Oil : 60 - 65 % Color Natural white Appearance Free from insect infestation, foreign bodies and metal. Flavour Mild, fresh and sweet characteristics of coconut with no off-flavour or odour Packing In 3-ply Kraft paper bags with inner sealed polyliner Size of Packing 25 kg net per bag Qty Per 20ft FCL 280 bags x 25 kg net (7 metric tons) Qty Per 40HC 560 bags x 25 kg net ( 14 metric tons)

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.

JHG tinted glass is produced by metal oxides to the float glass. The colour may be transferred in the series of blue, green, grey, bronze flexibly. The performance of visible light, privacy and solar heat transmission will be changed arrording the colour change. Different tinted glass offers varied application possibility-from interior partitions, to home appliance, to furniture, to facades and auto field. Reflective glass is float glass with a metallic coating that cuts off solar heat.The coating film may provide mirror effect, preventing visibility from outside and preserving privacy. JHG mainly offer 2 kinds of reflective glass. Hard reflective glass (on line) includes blue, green, grey, bronze, pink, silver colour, Soft reflective glass (off line) includes golden, silver, purple colur. Specification Sizes:1220*1830/1830*2440/1650*2140/2140*3300/2140*3660/2440*3660/2250*3660/3300*4500/5100/6000mm Thickness: 3-12mm Quality standard GB11614-2009/SGCC/EN 572

Specifications Material:Metal Metal Type:Tin Use:Coffee Shape:square tea tin Size:180*170*78mm Thickness:0.20-0.28mm Color:CMYK Printing:CMYK Off-set Printing Keyword:Tea tins Usage:Packing Product name:Square empty metal tea tin Logo:Customized Logo Lid:Removeable Lid

JHG offer differnt sizes of tempered glass, annealed glass to meet the inquiry for greenhouse ,hobby garden , Glass thickness is 3mm/3.2mm/4mm/5mm Glass items : clear float glass ,acid etched glass ,diffused glass high haze glass ,AR coated glass Max LT >99% Max haze>50%

SOLAR GLASS JHG solar glass including texture glass and flat glass ,it is the nice performance low iron glass with high solar transmittance, and low reflection . After tempered, it will be the ideal choice for photovoltaics, solar thermal collector ,and greenhouse . Size Maximum Size:1665*2200mm Minimum Size: 300*300mm Specifiction Main thickness 2-5mm Dimension tolerance �?�±1.0mm Thickness tolerance �?�±0.2mm Diagonal tolerance 0.2% Overall bow

JHG is professionally offering all various of high quality laminated glass: 1) PVB laminated glass Colour includes clear/milk/bronze/grey/blue/green/black PVB film thickness is 0.38/0.76/1.14mm or thicker Both standard size and customized sizes available 2)Sentryglass Plus(SGP)laminated glass SGP bring more safe,more transparent for construction ,the film includes 0.89/1.52/2.28mm and thicker mainly used for glass floor,glass step,glass fin,curtain wall Max size is 18000mm length 3)EVA laminated glass It can be laminated with large range of inserts including PET film,polycarbonates,wood veneer,metal,paper ,stones,screeen mesh ,and so on ,it will bring mulrirusinous choice for inner decoration.

HIPS Regrind White-Mix Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind White-Mix CATEGORY: HIPS TYPE: Regrind White-Mix SPECIFICATION Product- HIPS regrind post production from Yogurt caps Contamination â?? up to 2% foil metalizing (cover of the yogurt caps). Food grade material Post - industrial Sheet Extrusion & Vacuum forming Origin: Spain LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days