First, the construction conditions: 1, temperature: the general requirements of the site temperature above 10 degrees Celsius, the season is suitable for construction. 2, humidity: no more than 85%, the current season is suitable for construction. 3, ventilation: the best natural ventilation conditions, in the absence of wind, sand, rain, the outside temperature is not high, try to open the doors and windows for ventilation. 4, lighting: the requirements of indoor lighting, so you must meet the requirements of the construction site of the light. 5, water and electricity: the requirements of the construction site has power, water, in order to ensure the normal use of construction machinery. Two, safety and health site management: 1, the construction personnel must wear masks, gloves, wear your badge to enter the construction site. 2, closed area, wearing a breathing mask, to maintain the flow of fresh air. 3, in the construction process, construction personnel and construction site near the wall of the staff to breathe steam, no skin and eye contact material. 4, storage of materials, raw materials must stored in the shade, shelter, ventilation, away from the heat source of fire, prevent the ignition and or deterioration of the material. Placement of "no smoking" sign. 5, fire control measures: construction personnel shall not smoke, point fire. A fire extinguisher with carbon dioxide must be provided at the construction place. 6, the site protection: the prohibition of cross operation, construction period is strictly prohibited without the construction personnel to enter the site, any personnel to enter the construction site has been applied to the construction site inspection, must take off the shoes to enter the thick. Three, construction quality management: 1, the scene by 2 - 3 site Project Manager has overall responsibility for the construction quality, schedule, scheduling and other items, and the other is equipped with 3 - 5 construction technology supervisor. 2, the quality technology supervisor to follow the construction team, the whole process supervision, supervisor to in a timely manner to the project manager in the construction of occurrence problem, and solve the problem in time. 3, quality inspection: Project Manager and supervisor to strict inspection and check each one step, ensure each procedure are qualified, under the procedures in a timely manner.
Hollow Plastic Concrete Formwork for fundational building Size:1220*2440mm Thickness:15mm/18mm/20mm MOQ:100pcs Advantage:Reusable Application:concrete panels building formwork Color:Grey Weight:31kgs Quick Details: Product Name:Plastic concrete formwork Application:Concrete panels building formwork Material:PP plastic material Surface:Cleanly ,Glossy and smoothy Size: 1220*2440mm Thickness: 15mm, 18mm,20mm Type: Construction formwork Color: Grey Certificate: ISO9001:2008 Weight: 31KGS Packaging & Delivery Selling Units:Single item Single package size: 244X122X2.0 cm Single gross weight:31.0 kg Package Type:carton box packing onto wooden pallet Lead Time : Quantity(Piece)1 - 200201 - 336337 - 810>810 Est. Time(days)5715To be negotiated
We have range of patch fittings suitable for 8-15mm tempered glass doors. 1. Our patch fittings are suitable for 10mm, 12mm tempered glass doors 2. Bottom Patch fitting. 3. Top patch fitting. 4. Side Over panel. 5. Top center 6. Inserts available for most of the floor springs. 7. Aluminum, SS304. 8. Polished Stainless steel, Satin Stainless steel,aluminium oxsilver ,Aluminum Gold color.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Can supply: PP/PE PELLETS FLOOR SWEEP MIX COLOR IN BIG BAGS. Post industrial. Materials need washing. Can load in 1x40' HC container approx. 26 MT (10%) Ready for shipment. Photos available upon request. If you are interested kindly contact us for more information (price, available quantity etc.). You are welcome to visit our company premises and supervise our materials. Certificate ISO: 9001, ISO: 14001, OHSAS 45001, AQSIQ and CCIC.
WE ARE SUPPLYING FROM INDIA AND FAR EAST
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Epoxy Resin
Rose oils are extracted from the Rosa damascena (Bulgarian) and Rosa centifolia (Moroccan) also known as 'rose de mai'. Rose Otto is the essential oil steam distilled from fresh roses. Rose concrete a solvent extraction of fresh roses. Rose absolute is extracted from the rose concrete using alcohol. Rose Otto is distilled from the Bulgarian rose or Rosa damscena. The Otto is an almost clear pale yellow liquid. When it is very cold it solidifies but it is easily warmed to liquid again. Rose Otto smells rich, floral, warm and spicy with honey undertones. The smell of fresh roses becomes more apparent at when the Otto is diluted. Rose Otto is the most expensive extract of roses. Rose concrete from Rosa damscena is a deep orange colored mass of a jam-like consistency, can be greenish yellow.
Pu foam scrap, memory/ visco foam scrap. rigid foam scrap, pvc foam scrap. pp non woven waste, pvc resin off grade/wet, abrasive garnet, epoxy resin, polyester yarn scrap, raw cotton scrap, quartz ore and sulphur.Distributor of polyurethane trim foam scrap, sulphur, epoxy resin, polyester resin, quartz ore, recycled dacron and abrasive garnet.
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
HIPS repro pellet mixed color from yoghurt caps HIPS Recycled Pellets Thermoplastics PS has two representatives, GPPS and HIPS. In particular, PS HIPS plastic is the most popular to many advantages and applications. HIPS belongs to the group of hard, transparent resins that are easy to create color, processed by laminating film lamination and easy laminating technology. What is HIPS PLASTIC ? HIPS pellet stands for High Impact Polystyrene. Polystyrene has the chemical formula Polystyrene (C8H8)n which is a long chain hydrocarbon in which alternating carbon centers are attached to the phenyl group (the name given to the aromatic benzene ring). MATERIAL: HIPS repro pellet mixed color from yoghurt caps CATEGORY: HIPS repro TYPE: Pellet GRADE: Mixed color SPECIFICATION: Mixed color.from yoghurt caps Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 900$ - 1150$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Focus-6200 products are kind of non-hardening and self-adhesive waterproof sealing butyl tapes. The materials are weathering resistance and fully accommodate to the surface that it attached to, with effective life up to 20 years. Main Specification (Customized size is acceptable.) 2mm thickness * 20mm width * 20mm roll length 2mm thickness * 30mm width *20mm roll length Main Color - black, grey, white Technical Data Product Series FOCUS-6200 Series Application Construction Industry Elongation - 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 25N/cm Tensile Strength 250KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet Advantages * Never hardening, maintain good waterproofing property with weathering resistance performance. * Excellent performance in waterproofing and sealing. * Good anti-aging performance effective life up to 20years. * Easy to apply. Applications * Provide waterproof and sealing protection forsteel structure construction. * Provide waterproof and sealing protection for door joints, window joints,roofs and air-ducts. Provide waterproof and sealing protection for sunshine rooms, light plate rooms and thermostatic chamber. * Provide repair function for leaks on surfaces of metal/plastic/glass/concrete.
Color index, number : 18 Hot alcoholInsolubile,% : 1.00 Application: 1. The plasticity and castability of heating, combined with its ability to absorb a large amount of infiltrated material, is of great value in the casting industry. 2. The lac resin is non-toxic. Based on the excellent characteristics listed above, the shellac resin is applied to alcohol paints, electrical insulating materials, printing inks, rubber fillers, and its use for oil and acid resistance. 3. Other industries: It has a wide range of important application value in many fields such as medicine, food, cosmetics, chemical industry, metallurgy, machinery, woodware, papermaking, electronics and military industry.
Annatto, sometimes called roucou or achiote, is derived from the seeds of the achiote trees of tropical and subtropical regions around the world. The seeds are sourced to produce a carotenoid-based yellow to orange food coloring and flavor. Annatto is commonly used in Latin American and Caribbean cuisines as both a coloring and flavoring agent. Central and South American natives use the seeds to make body paint and lipstick. For this reason, the achiote is sometimes called the "lipstick-tree". Achiote originated in South America and has spread in popularity to many parts of Asia. It is also grown in other tropical or subtropical regions of the world, including Central America, Africa and Asia. Annatto is a naturally intense dye which can range in color from bright yellow to deep orange. Many commercially made food products utilize annatto for its potent color.
Giva Agro's Pure Shilajit Resin is the closest natural form of Shilajit. Apart from following an ayurvedic purification, no chemical or other outside ingredient is added. That is what makes resin the most potent form of shilajit. Other names of shilajit : Shilajeet, salajit, shilajatu, mimie, or mummiyo, mumijo Properties: Fulvic acid,Humic acid,Selenium Botanical name: Asphaltum punjabianum Product : Pure shilajit resin Form available: Resin/Semi Liquid Country of Origin: Himalayas, Made in India Speciality: No sugar, No Preservatives, No artificial color or harmful Chemical added. Non GMO, Gluten Free, Does NOT Contain Soy, Gelatin, Egg, Dairy or Caffeine, No Additives or Fillers Benefits of Shilajit: 1.Provides energy and revitalisation 2.Regulates hormones and immune system 3.Alleviates pain response 4.Helps with weight loss 5.May help manage Diabetes 6.Promotes healthy metabolism 7.Fights inflammation and builds immunity 8.Potentially aid in breaking of addictions. To have our own private labelled Shilajit,
lldpe/ldpe floor sweeps from film manufacturing only mostly natural color contains small amounts of: purge, leaves, wood, cardboard, color concentrate needs to go through wash line , 1load is available, loading weight : 35,000 pounds/cont USA orgin, subject to unsold
Applications: In making Calcium Carbonate that can be used in color, paper, paint and chemical factories As decorative stones and landscaping stones As counter tops As building material In sculpture
Product Name: Disposable Vinyl/Nitrile Blend Examination Gloves One-time use, no sterilization, no latex Single use, non-sterile, Latex free Model: S, M, L, XL Sizes: S, M, L, XL Color: blue, green, black, etc. Color: Blue, Green, Black etc. Structure: 5 fingers, with curling, regardless of left and right hands Structure: 5 fingers, beaded cuff for easy donning, ambidextrous Surface type: smooth surface Surface: Smooth Features : PVC/nitrile synthetic gloves are made of PVC resin and nitrile latex material. The product has PVC and The double advantage of nitrile gloves. The Vinyl/Nitrile Blend gloves is compounded with PVC paste and Nitrile latex, and the finished product has the advantage of both PVC and Nitrile glove. The donning feeling is better than vinyl gloves. Much softer than vinyl gloves Sturdy, wearable, longer wearing time than nitrile gloves The wearing time is longer than nitrile gloves. Has good wet hand wearability, easier to wear than nitrile and PVC gloves Easy donning with wet hands and easy donning than nitrile &vinyl gloves. PU coating, free of protein, effectively reduces the risk of allergies PU coating, with no protein in it, allergy risk is reduced effectively. Has better protection, has better acid resistance, alkali resistance and oil resistance Better protection, good resistance of acid, alkali and oil. Better cost-performance
