Application: PR-A series Hydrocarbon Resin are suitable for adhesives, including quick packaging adhesives, bookbinding adhesives, wood adhesive, adhesive tape and glue sticks. They also can be used singly as tackifier resin in adhesive, and can also be used in blends with different resins to improve adhesive performance. Specification: Grades/Properties PR-A1100 PR-A2100 Testing Methods Appearance Granule Granule Eyeballing Softening Point °C 100 ±3 100 ±3 ASTM E 28 Color(Ga.) 3-4max 3-4 max ASTM D-1544 Acid Value (KOHmg/g) =0.5 =0.5 ASTM D 974 Melt Viscosity (200 °C) cps =230 =230 ASTM D-3236 Insoluble Vol% =0.05 =0.05 ASTM E 99 Molecular Weight =5000 Package Packed in 25kgs paper bag, pp bag or paper and pp compounding bags;17MT without pallets or 14.5MT with pallets for 1*20 FCL.Also can use 750kgs container sack,15MT with pallets for 1*20 FCL.
TA5100 is hydrocarbon resin which is suitable for hot-melting adhesives, (including quick packaging adhesives,book binding adhesives, wood adhesives and glue sticks, etc.) They have excellent compatibility with SIS, SBS ,EVA ,natural rubber and many kinds of synthetic rubbers . They provide enhanced performance in hot melt adhesive applications. Features of TA5100 in Hot Melt Adhesive and Pressure Sensitive Adhesives: Good open time / set time balance, Good adhesive ability Excellent aging stability Light color Applications: Hot melt adhesive, pressure sensitive adhesive
Resins characters: Light colored and transparent granule Make the initial adhesion performance; cohesive strength and peel strength reach the best balance Super aging resistance performance Good fluidity which can improve the wetting property of master material. Narrow molecular weight distribution Low volatility and no odor Excellent compatibility with cinnamene copolymers (such as sis, sbs, sebs and seps), nr, sbr, eva and natural sticky resins(such as terpene, gum resin and its ramification). Application: Hot melt adhesive, solventborne adhesive, pressure sensitive adhesive, rubber compounding, tyre.
C5 aliphatic hydrocarbon resin for hot melt adhesives C5 Hydrocarbon resin is playing gradually more and more important role as tackifier in the adhesive and sealant industry, especially in the application of hot melt adhesive and pressure sensitive adhesive. The series of petroleum resins product are a category of C5 aliphatic hydrocarbon resins applicable for hot melt adhesive and pressure sensitive adhesive. These products have an excellent compatibility with a wide variety of elastomers including natural rubber (NR), synthetic rubber, Ethylene Vinyl Acetate (EVA) and styrenic block copolymer such as SIS, SBS, SEBS, SEPS. Additionally, they also have a good compatibility with the natural tackfying resins such as terpene, rosin and thereof derivatives. At the same time, all the properties of adhesive can be improved in various degrees by the application of these C5 petroleum resins. In recent years, C5 petroleum resins are gradually replacing the natural resin tackfier(such as terpene and rosin) due to its advantages of high deep strength, fast tack, stable adhesion performance, moderate melting viscosity, high thermal resistance, good compatibility with polymer basis, economic price. Good fluidity which can improve the wetting property of master material. Excellent initial adhesion performance Super aging resistance performance Light color material Transparent, little smell and low volatility material Application field: hot melt adhesives, solvent base adhesives, adhesives, sealants, glue etc
TC100 / copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive C5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, TC100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.TC100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, TC100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive durability and bonding strength. Product Specification: Item Test Method Unit Specification Range Softening Point ASTM-E28-58 95-105 Color ASTM-D-1544 GC 4Max Insoluble ETM-E-99 Vol% 0.05Max Acid Value ASTM-D-974 Vol% 0.2Max Specific Gravity ASTM-D-71-72A g/ 0.99-1.03 Features of TC100 C5/C9 Copolymerized Hydrocarbon Resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with EVA,SIS and SBS etc. Applications:Hot melt adhesive,Synthetic rubber
Tc100/ copolymerized hydrocarbon resin is produced with and fraction, which has and strengths.It can replace the expensive c5 hydrocarbon resin in hot melt adhesive and rubber tire fields. In rubber tires, tc100 hydrocarbon resin not only can increase the adhesive force between colloidal particles, but also can enhance the adhesion between the particle and the cord thread.Tc100 hydrocarbon resin is suitable for producing high quality rubber products. In adhesive, tc100 hydrocarbon resin have better initial adhesion and it also can adjust the adhesive, s durability and bonding strength. Product specification: Itemtest methodunitspecification range Softening pointastm-e28-58 , 95-105 Colorastm-d-1544gc4max Insolubleetm-e-99vol%0.05max Acid valueastm-d-974vol%0.2max Specific gravityastm-d-71-72ag/0.99-1.03 Features of tc100 c5/c9 copolymerized hydrocarbon resin: Wide optional range.It will be more stabilized by the addition of antioxidant.Good compatibility with eva, sis and sbs etc. Applications:hot melt adhesive, synthetic rubber Package: 25kg kraft paper bag Storage: All resins with low softening point present a risk of solidifying or lump. For softening point less or equal to 110, , we suggest you keep resin in a cool (25, max) ventilated place and avoid direct sunshine.
Tr5100 hydrocarbon resin is a low molecular weight aliphatic hydrocarbon resin that has been designed for hot melt road marking system. It can enhance the adhesion and hardness of road marking paint, and make paint in stable situation in the four seasons. Application: hot melt road marking paint Features of tr5100 in hot melt road marking: Light color Good fluidity High anti-fraction Even distribution of filling material without sedimentation. Good heat stability Fast drying speed Good weather resistance, adhesive force and stain resistance.
C5 Hydrocarbon resin is a pale yellow C5 aliphatic hydrocarbon resin having excellent color, flow, and heat stability and thus highly recommended for Hot Melt Road Marking Paints FEATURES: Light Colour Gradient - Excellent Fluidity- Better Heat Stability - High Drying Rate and Anti - Abrasion Outstanding affinity for pigments Superior Process Ability Strong dirt-resistant
C5 Petroleum Resin with Grade SENO-PC5100 is a high class refined C5 Aliphatic Hydrocarbon Resins designed specially as a Binder to meet the technical requirements for hot melt road marking paint in Asian and American Markets.Our C5 petroleum resins offer good dispersion of fillers and pigments and also show excellent flow properties in Hot Melt Road Marking Paint Systems. Our C5 Hydrocarbon Resins are mainly recommended to the Thermoplastic Road Marking Paint and Hot Melt Road Marking Paint industry. Product Parameters Items SENO-PC5100 Appearance (eyeballing) yellowish granule Softening Point (R&B)�ºC 95-105 Color No. (50% Toluene)Ga. 5.0 Max Acid Value(mgKOH/g) 1.5 Max Ash Content(wt%) 0.10 Max Melt Viscosity(200�ºC)Cps 250 Max Application : SENO-PC5100 mainly use for Hot Melt Road Marking Paint,Thermoplastic Road Marking Paint and Pressure Sensitive Adhesives Packaging & Shipping :25kg/bag Store closed containers in a cool, dry, well-ventilated area. Avoid exposure to direct sunlight.
PG100 resin is a kind of C5 modified C9 resin, with both character of C5 and C9 component, which is designed to tackify a variety of adhesive polymers, including ethylene vinyl acetate (EVA), styrenic block copolymers (SIS, SBS, SEBS), amorphous polyalphaolefins (APAO).
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
PC/ABS regrind full container available MATERIAL : PC/ABS regrind full container available CATEGORY : PC/ABS TYPE : Regrind GRADE : Black color SPECIFICATION : 1 full container available Origin : Tunisia LOADING WEIGHT : 23 Ton FOB (USD/Ton:) : 850$ - 1000$ Packaging : Jumbo Bag Est. Shipping Time : 15, 30, 45 days
PA66 FR regrind black color Pa6 / pa66 is mainly applied as follows: 1. Improves nylon water absorption and improves size stability of the product. 2. Improved nylon fire resistance to meet the requirements of electronics, electrical, communications and other industries. 3. Improved mechanical strength of nylon to achieve the strength of metal materials, metal replacement. 4. Improves nylon low-temperature resistance and enhanced resistance to environmental stress. 5. Improves nylon wear resistance to meet high wear resistance requirements. 6. Improves nylon antistatic properties to meet its extraction requirements and mechanical applications. 7. Improves nylon heat resistance to adapt to high temperature conditions such as car engines. 8. Reduce nylon cost and improve product competitiveness. Through the above modification, high performance and functionalization of nylon composite materials are realized, thereby promoting the development of industries involving high performance and high quality. MATERIAL : PA66 FR regrind black color CATEGORY : PA66 FG TYPE : Regrind GRADE : Black color SPECIFICATION : GF50. 1 full container available Origin : Tunisia LOADING WEIGHT 23 Ton FOB (USD/Ton) : 750$ - 950$ Packaging : Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS repro pellet mixed color from yoghurt caps HIPS Recycled Pellets Thermoplastics PS has two representatives, GPPS and HIPS. In particular, PS HIPS plastic is the most popular to many advantages and applications. HIPS belongs to the group of hard, transparent resins that are easy to create color, processed by laminating film lamination and easy laminating technology. What is HIPS PLASTIC ? HIPS pellet stands for High Impact Polystyrene. Polystyrene has the chemical formula Polystyrene (C8H8)n which is a long chain hydrocarbon in which alternating carbon centers are attached to the phenyl group (the name given to the aromatic benzene ring). MATERIAL: HIPS repro pellet mixed color from yoghurt caps CATEGORY: HIPS repro TYPE: Pellet GRADE: Mixed color SPECIFICATION: Mixed color.from yoghurt caps Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 900$ - 1150$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days