Battery Contact Probe Test Pogo Pin BIP48 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP48 series of battery contact probes. The outside diameter is usually 4.8 mm and total length is 6.8 mm. There are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 5.95 mm (235 mil) Current Rating: 5 Amps, continuous Contact Resistance: 30 milliohms (Maximum) Full Stroke: 2.15 mm Rated Stroke: 1.27 mm Spring Force: 23 gf (0.8 oz)/ 56 gf ( 2 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Brass, Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
Battery Contact Probe Test Pogo Pin BIP39 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. � Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. � The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP39series of battery contact probes. The outside diameter is usually 3.89 mm � and there are some common tip styles, for example � J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 5.084 mm (200 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 2.6 mm Rated Stroke: 1.7 mm Spring Force: 113/ 255 gf (4/ 9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Brass, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Battery Contact Pogo Pin Test Probe BIP16 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative.� The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP16 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 2.5 mm Rated Stroke: 1.8 mm Spring Force: 95 gf (3.4 oz) Materials Contact Barrel: Brass, Gold Plated Spring:� Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Pogo Pin Test Probe BIP47 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP47 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 20 milliohms (Maximum) Full Stroke: 1.5 mm Rated Stroke: 1.5 mm Spring Force: 80 gf (2.8 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Battery Contact Probe Test Pogo Pin BIP148 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP148 series of battery contact probes. The outside diameter is usually 1.49 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.16 mm (85 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 2 mm Rated Stroke: 1.33 mm Spring Force: 25 gf (1/ 0.9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP114 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP114 series of battery contact probes. The outside diameter is usually 1.14 mm and there are some common tip styles, for example round head or pointed head. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 1.14 mm Rated Stroke: 1.14 mm Spring Force: 110 gf (4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Product Description gel accumulator 2v 800ah (OPzV800-2) OPZV800-2 Opzv Series Valve Regulated Lead Acid batteries are designed with a proven combination of GEL and Tubular technologies to offer a very high level of reliability. Opzv batteries benefit from an optimized plate design which gives capacities in excess of the DIN standard values. In addition, this series offers both a longest float life and a high cycle life in widely industrial field. Safety and Sealed No electrolyte leakage will occur from terminals or case or case of any Storace Battery ensuring safe and efficient operation. Maintenance-Free operation There is no need to add water thanks to unique gas recombination system which totally transforms the generated gas into water. Storace batteries do not need the equalizing charge As a result of monomer battery's interface resistance capacity and float voltage uniformity are fine. No Free Acid The special electrolyte retentive separators bold the acid and thus there is no free acid inside the battery, and therefore the battery can be mounted in any position. Long life Design The use of heavy -duty lead-calcium alloy grids with anti-corrosive construction enables the Storace AGM battery to remain in float service for 10-15 years; the GEL battery to remain in float service for 15-20 years. The cycle life can be more than 1000 cycles High Reliability and stable quality With advancing AGM and GEL production technology and strictly quality control system, the battery quality is stable and the battery performance is reliable. The voltage, capacity and seal are 100% tested on line. Self-discharge The self-discharge rate in room temperature is approximately 2% of nominal Capacity per month. Operating temperature TheStorace Battery can be operated between -40�°C to +65�°C.The battery can give out over40% fo nominal capacity at -40�°C.
Specification Shell type LFP51.2-400-MT-XDD Available electricity 21.094Kwh Rated capacity 400Ah Combination mode 16S2P BMS conifguration 16S400A Rated voltage 51.2V Operating voltage range 41.6V~59.2V Rated charge and discharge current 200A Peak current 400A Continue @410A 3s Rated charging and discharging power 10.24Kw Peak power 20.48Kw Continue @20.99Kw 3s Short-circuit current 0.8Ka@100us Cycle life 6000 Cycle 80%DOD, 25 Communication mode CAN, RS485 Parallel number No Remote data Bluetooth optional/Wifi Weight 170kg Dimensions (L*W*H) mm 585*280*1100mm Operating temperature Charging 0 ~+50 / Discharge -10 ~+60 Relative humidity 0~95% Storage temperature 3 Months -10 ~25 / 1 Year 0 ~25 Maximum working altitude 2000m Class of protection IP21 Supports inverter communication brands SMA/Growatt/TBB/Deye/GOODWE/Huawei/ Schneider/Victon energy/SOFAR/INVT Installation mode Floor mounting Power cable outlet mode Flank Standards and certification Transport UN38.3 *1 Test conditions, cell voltage 2.6V~3.65V, the new battery at +25 ±2 0.5C charging and discharging, available power may vary depending on the inverter; *2 Rated charge and discharge current and power will change due to temperature and SOC. If you have some problems about Gel Battery , or want to know more details about Storage Battery, LiFePO4 Battery, Uninterruptible Power Supply, Portable Power Station, Solar Power System, etc. Welcome to contact us! Pustunpower.com: lifepo4 battery 48v 51.2v, 50ah,100ah,150ah,200ah,300ah,400ah LiFePO4 Battery Pack Tags Lifepo4 Battery Manufacturers, Lifepo4 Solar Battery, Storage Battery manufacturers
Battery Contact Pin Test Probe BIP80 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP80 series of battery contact probes. The outside diameter is usually 0.8 mm and total length is 11 mm. There are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 1 mm Rated Stroke: 0.9 mm Spring Force: 60 gf (2.4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated
Spring Pogo Pin Battery Contact Test Probe BIP94 for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP94 series of battery contact probes. The outside diameter is usually 0.94 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 0.78 mm Rated Stroke: 0.7 mm Spring Force: 30 gf (1.05 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu/SK4, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PHONE SCRAP HS Code 85437090 PRICE = US$400/TON CIF ORIGIN: THAILAND PACKAGE: 1KG,5KG,10KG,15KG,25KG,50KG MIN ORDER:100 TONS DESCRIPTION Product Description Dear client WE HAVE VERY HIGH YIELD GOLD RECOVERY CPU CERAMIC PROCESSOR SCRAPS AND COMPUTER MOTHERBOARD SCRAPS FOR SALE We can supply cpu ceramic processor scraps Intel 186 / 286 / 386 / 486 / Pentium / Pentium Pro / i860 / i960 Cyrix 486 / 586 / MIIIBM 486 / 586 / 686 Motorola 68000 / 88000 series NEC Toshiba MIPS series: R4000 / R8000 / R10000 / R12000 1-Gold Top Cpu... 2-Gold Top&Bottom Cpu.. 3-Intel 186/286/386/486/Pentium/Pentium Pro/i860/960/... 4-Cyrix486/586/MIIIBM486/586/686/ .. 5-RAM (memorys)... We can supply on monthly basis around 10-50 tons per month of Ceramic cpu scrap for gold recovery and scrap motherboards and lan cards. We also supply sample order from 100 KGS. Our prices changes according to your order. For bulk order or sample order, contact us for our quote. Specification and use: Usage: For electrical industries Suitable to manufacture numerous electrical components, cables, cans, etc 1.Motherboard And other Computer Scrap 2.Untested condition 3.For recycling 4.Stock available PS / ABS bales scrap-waste from electric and electronic devices (TV SHELL-CASE, COMPUTERS etc.) CAN LOAD IN 1X40\'HC CONTAINER APROX. 22 TONS (-+10%) We can sell you you the following scrap: Computer Mother Boards Computer Finger Boards Computer Memory Computer Processors Computer Power Supplies Computer Hard Disks Computer Floppy Drives Computer CD Rom Computer Cases Computer Wires Computer Keypads Computer Mouse Computer UPS or Lead batteries from UPS Cell Phone Handsets Cell Phone PCB Boards Cell Phone Batteries Lithium Cell Phone Batteries Nickel Cell Phone LCDs Cell Phone Housings Cell Phone Chargers
FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Cable Television Communication Equipments Electric Power Systems Security Systems UPS systems Control Equipments Medical Equipments Emergency Power Systems Power Plant Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container. Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity. Specifications Nominal Voltage : 12V Capacity @ 20 HR : 12 AH Dimensions (mm)L : 150 Dimensions (mm)W : 98 Dimensions (mm)H : 95 Dimensions (mm)TH : 100 Battery Weight (Kg) : 3.6
6-GFM-18 FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 �°C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Uninterruptible Power Supply (UPS) Emergency Lightning Power Plants Telecom Backup Power Supplies Lawn & Garden Tools Gen set starting Auto Control Equipments Solar Energy Railway Signaling System Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate. Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container. Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity. Specifications Nominal Voltage 12V Capacity @ 20 HR 18 AH Dimensions (mm)L 180 Dimensions (mm)W 75 Dimensions (mm)H 168 Dimensions (mm)TH 168 Battery Weight (Kg) 5.7
6-GFMJ-20 FEATURES AGM & Gel Technology Available in 12 Volts & 2 Volts Series 10 Years Design Life (25 �°C) Front Access Terminal for easy Installation & Maintenance Flame Retardant Container & Cover with ABS Material High Reliability & Long Cycle Life PRODUCT APPLICATION Uninterruptible Power Supply (UPS) Emergency Lightning Power Plants Telecom Backup Power Supplies Lawn & Garden Tools Gen set starting Auto Control Equipments Solar Energy Railway Signaling System Characteristics Battery capacity and performance. The AGM has more electrolytes because the gelling agent displaces the electrolytes. This give the battery 7%-8% more duration capacity. The AGM also has a lower internal drop that allows a longer run despite a high discharge rate Elevated temperature. The AGM battery is more efficient in the oxygen recombination cycle that allows it to draw 50% more float current. But the Gel cell is 15% more efficient in heat conduction because the gelled electrolytes are in complete contact with the plates and walls of the container Float service life. Both the AGM and Gel VRLA batteries have the same 95%-100% capacity Specifications Nominal Voltage 12V Capacity @ 20 HR 20 AH Dimensions (mm) L 180 Dimensions (mm) W 76 Dimensions (mm) H 175 Dimensions (mm) TH 126 Weight KG 8.0
Test Probe Pogo Pin PL50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PL50 series here. Its test center is 50 mil, namely 1.27 mm. The diameter is 0.68 mm and the total length is 27.53 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles, namely CR, VCR, SC, VSC, CRW and VCRW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: Diameter 0.95 mm Full Stroke: 3.7 mm Rated Stroke: 2.54 mm Spring Force: 28/56/85 gf (1/2/3 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper/SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPC035 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC035 we will introduce is 0.35 mm in barrel diameter and 7.7 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.5 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.5 mm, the loaded force is about 18 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel Phosphor Bronze, Au on Ni Plated Bottom Plunger Beryllium Copper, Au on Ni Plated Top Plunger Beryllium Copper, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 2.5 amps Contact Resistance 100 milliohms max Bandwidth 5.8 GHz at -1dB Inductance 1MHZ at -0.01039 uH Captance 1MHZ at 2.35287 uF Specifications: Full Stroke 1 mm Rated Stroke 0.5 mm Spring Force 18 �±5 gf at load 0.5 mm Mechanical Life about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Test Probe Pogo Pin P166 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P166 series here. Its diameter is 1.66 mm and the total length is 48.4 mm. Various tip styles, for example, B3, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 5 mm Spring Force: 500 gf (11 oz) Materials Contact Barrel: Brass, Nickel Plated Spring: Music Wire, Nickel Plated Plunger: Steel, Nickel Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Printed Circuit Board Assembly Test Probe Pogo Pin PQ75 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ75 series here. Its test center is 75 mil. The diameter is 1.02 mm and the total length is 33.02 mm. Various tip styles, for example, H, K, L, BK, etc., are available for test probes. There are three types of receptacles, namely CR, SC and WW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 112/150/198 gf (4/5.5/7 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPA030 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA030 we will introduce is 0.3 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 10 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.1 GHz at -1dB Inductance: 1MHZ at -0.02524 uH Captance: 1MHZ at 1.12735 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 10 ±3 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
