SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system. Product Features: 1. Standardized components, modular architecture, easy for expansion. 2. High energy density, small footprint, short construction period, strong environmental adaptability 3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional 5. BMS battery management system with SOC automatic calibration and high current passive balancing function, combined with the perfect operation control and management strategies to achieve accurate and efficient management 6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system. 7. Our BMS system adopts American NXP automotive grade chips with high performance. 8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform. 9. Colorful LCD display all module working information and status.
The Dry Battery PTZ7L - 12V - 7Ah is a Valve Regulated Lead Acid sealed lead acid battery (referred to as VRLA) designed by AGM technology. AGM technology uses an Absorbed Glass Mat as a barrier; the electrolyte solution is absorbed at the plate, and the diaphragm is faster. Lead alloy composition and special additives suitable for starting purposes Advanced technology with an acid-free regulator valve, safe for users and vehicles. Outstanding advantages of the Dong Nai Maintenance-Free Dry Battery (VRLA) PTZ7A (12Vâ??7Ah) Specially designed for motorcycles. The most advanced technology for high performance, increased battery start-up, and service life Completely free of maintenance during use. Anti-shake design, suitable for all different terrain conditions.
The Dry Battery PTZ7L - 12V - 7Ah is a Valve Regulated Lead Acid sealed lead acid battery (referred to as VRLA) designed by AGM technology. AGM technology uses an Absorbed Glass Mat as a barrier; the electrolyte solution is absorbed at the plate, and the diaphragm is faster. Lead alloy composition and special additives suitable for starting purposes Advanced technology with an acid-free regulator valve, safe for users and vehicles. Outstanding advantages of the Dong Nai Maintenance-Free Dry Battery (VRLA) PTZ7A (12Vâ??7Ah) Specially designed for motorcycles. The most advanced technology for high performance, increased battery start-up, and service life Completely free of maintenance during use. Anti-shake design, suitable for all different terrain conditions.
The Duracell MX2500 AAAA battery is a type of cylindrical alkaline battery commonly used in various electronic devices that require a compact power source. AAAA batteries are smaller than AAA batteries and are often used in devices with slim designs or specific requirements. Duracell is a well-known brand in the battery industry, known for producing reliable and long-lasting batteries. The MX2500 AAAA battery is used in a range of devices such as stylus pens for tablets, medical devices, laser pointers, and more. It's important to note that AAAA batteries are less common than other battery sizes, so it's advisable to ensure compatibility before purchasing.
Specification Shell type LFP51.2-400-MT-XDD Available electricity 21.094Kwh Rated capacity 400Ah Combination mode 16S2P BMS conifguration 16S400A Rated voltage 51.2V Operating voltage range 41.6V~59.2V Rated charge and discharge current 200A Peak current 400A Continue @410A 3s Rated charging and discharging power 10.24Kw Peak power 20.48Kw Continue @20.99Kw 3s Short-circuit current 0.8Ka@100us Cycle life 6000 Cycle 80%DOD, 25 Communication mode CAN, RS485 Parallel number No Remote data Bluetooth optional/Wifi Weight 170kg Dimensions (L*W*H) mm 585*280*1100mm Operating temperature Charging 0 ~+50 / Discharge -10 ~+60 Relative humidity 0~95% Storage temperature 3 Months -10 ~25 / 1 Year 0 ~25 Maximum working altitude 2000m Class of protection IP21 Supports inverter communication brands SMA/Growatt/TBB/Deye/GOODWE/Huawei/ Schneider/Victon energy/SOFAR/INVT Installation mode Floor mounting Power cable outlet mode Flank Standards and certification Transport UN38.3 *1 Test conditions, cell voltage 2.6V~3.65V, the new battery at +25 ±2 0.5C charging and discharging, available power may vary depending on the inverter; *2 Rated charge and discharge current and power will change due to temperature and SOC. If you have some problems about Gel Battery , or want to know more details about Storage Battery, LiFePO4 Battery, Uninterruptible Power Supply, Portable Power Station, Solar Power System, etc. Welcome to contact us! Pustunpower.com: lifepo4 battery 48v 51.2v, 50ah,100ah,150ah,200ah,300ah,400ah LiFePO4 Battery Pack Tags Lifepo4 Battery Manufacturers, Lifepo4 Solar Battery, Storage Battery manufacturers
Basic Info. Model NO. LFP51.2-300 Electrolyte LiFePO4 Color White Usage Solar/ Marine/ Telecom / Electric Mobility Warranty 3 Years OEM/ODM Acceptable Package Carton and Pallet Lead Time 20-30 Days Dimension 720*260*580mm Transport Package Wooden Case Specification 120kg Trademark PUSTUN Origin China HS Code 8507600090 Production Capacity 5000 Product Description Product Description Factory Wholesale Deep Cycle 51.2V300ah Lithium Ion Batteries LiFePO4 Lithium iron phosphate battery is a kind of lithium ion battery that uses lithium iron phosphate (LiFePO4) as the positive electrode material and carbon as the negative electrode material. It has the advantages of high working voltage, high energy density, long cycle life, good safety performance, low self-discharge rate and no memory effect. Pustun lithium iron phosphate battery is your best power choice for energy storage system of solar street light. This LFP series battery is specifically designed for solar street light application, which has more than 10 years service life; LFP series batteries are the best choice for the durable, safe, environment-friendly energy solution and they can be customized according to your requirement, such as dimension, voltage, capacity of battery. With an increased lifespan, this battery can save you much cost against frequent battery replacement. The working life of lithium battery especially under the outdoor high temperature environment is five times longer than the traditional lead acid battery. Product Parameters Nominal Voltage 51.2V Nominal Capacity 300Ah Energy 15.36KWh Combination mode 16S1P Cycle Life â?¥6000 Cycle, 80%DOD, 25�ºC BMS conï¬?guration 16S150A Operating voltage range 41.6V~59.2V Rated charge and discharge current 150A Peak current 160A Continue @170A 3s Rated charging and discharging power 7.68Kw Peak power 8.192Kw Continue @8.704Kw 3s Short-circuit current 0.762Ka@100us Communication mode CAN, RS485 Parallel number Recommend 6 in parallel(Maximum support 16 in parallel) Remote data Bluetooth optional/Wiï¬? Weight 120kg Dimensions (L*W*H) mm 720*260*580mm Operating temperature Charging: 0�ºC~+50�ºC / Discharge: -10�ºC~+60�ºC Relative humidity 0~95% Storage temperature
Basic Info. Model NO. LFP25.6-100 Electrolyte LiFePO4 Color White Usage Solar/ Marine/ Telecom / Electric Mobility Warranty 3 Years OEM/ODM Acceptable Package Carton and Pallet Lead Time 20-30 Days Dimension 750*145*250mm Transport Package Carton Specification 28kg Trademark PUSTUN Origin China HS Code 8507600090 Production Capacity 5000 Product Description Product Description 25.6V100ah Renewable Energy Lithium Ion LiFePO4 Battery Lithium iron phosphate battery is a kind of lithium ion battery that uses lithium iron phosphate (LiFePO4) as the positive electrode material and carbon as the negative electrode material. It has the advantages of high working voltage, high energy density, long cycle life, good safety performance, low self-discharge rate and no memory effect. Pustun lithium iron phosphate battery is your best power choice for energy storage system of solar street light. This LFP series battery is specifically designed for solar street light application, which has more than 10 years service life; LFP series batteries are the best choice for the durable, safe, environment-friendly energy solution and they can be customized according to your requirement, such as dimension, voltage, capacity of battery. With an increased lifespan, this battery can save you much cost against frequent battery replacement. The working life of lithium battery especially under the outdoor high temperature environment is five times longer than the traditional lead acid battery. Product Parameters Nominal Voltage 25.6V Nominal Capacity 100Ah Energy 2.56KWh Combination mode 8S1P Cycle Life â?¥6000 Cycle, 80%DOD, 25�ºC BMS conï¬?guration 8S100A Operating voltage range 20.8V~29.6V Rated charge and discharge current 100A Peak current 100A Continue @120A 3s Rated charging and discharging power 1.28Kw Peak power 2.56Kw Continue @3.072Kw 3s Short-circuit current 0.225Ka@100us Communication mode CAN, RS485 Parallel number Recommend 6 in parallel(Maximum support 16 in parallel) Remote data Bluetooth optional/Wiï¬? Weight 28kg Dimensions (L*W*H) mm 750*145*250mm Operating temperature Charging: 0�ºC~+50�ºC / Discharge: -10�ºC~+60�ºC Relative humidity 0~95% Storage temperature
The 19 inches rack standard backup battery is based on Lithium iron phosphate battery, It has been designed to provide backup power for telecom equipment or energy storage system in household. It has excellent safety, high energy density, long lifetime, very nice temperature performance, green power newly of excellent safety and high reliability. Custom capacity is acceptable. High cycle life 4000 cycles @80% DoD for effectively lower total of ownership cost. Longer service life Low maintenance batteries with stable chemistry. Built in circuit protection Battery Management System (BMS) is incorporated against abuse. Better storage Up to 6 months thanks to its extremely low self discharge (LSD) rate and no risk of sulphation. Quickly recharge Save time and increase productivity with less down time thanks to superior charge/discharge efficiency. Extreme heat tolerance Suitable for use in a wider range of applications where ambient temperature is unusually high: up to +60C. Lightweight Lithium batteries provide more Wh/Kg while also being up to 1/3 the weight of its SLA equivalent. Function Support parallel operation
The wall mounted Lithium battery (LiFePO4 Battery) solutions are highly integrated, deep cycle backup power solutions for your solar home energy storage system. With rich experience and advanced techniques, the product has the features of the fashionable design, high energy, high power density, long service life, and easiness of installation and expansion. Custom capacity is acceptable. High cycle life 4000 cycles @80% DoD for effectively lower total of ownership cost. Longer service life Low maintenance batteries with stable chemistry. Built in circuit protection Battery Management System (BMS) is incorporated against abuse. Better storage Up to 6 months thanks to its extremely low self discharge (LSD) rate and no risk of sulphation. Quickly recharge Save time and increase productivity with less down time thanks to superior charge/discharge efficiency. Extreme heat tolerance Suitable for use in a wider range of applications where ambient temperature is unusually high: up to +60C. Lightweight Lithium batteries provide more Wh/Kg while also being up to 1/3 the weight of its SLA equivalent. Function Support parallel operation
The wall mounted Lithium battery (LiFePO4 Battery) solutions are highly integrated, deep cycle backup power solutions for your solar home energy storage system. With rich experience and advanced techniques, the product has the features of the fashionable design, high energy, high power density, long service life, and easiness of installation and expansion. Custom capacity is acceptable. High cycle life 4000 cycles @80% DoD for effectively lower total of ownership cost. Longer service life Low maintenance batteries with stable chemistry. Built in circuit protection Battery Management System (BMS) is incorporated against abuse. Better storage Up to 6 months thanks to its extremely low self discharge (LSD) rate and no risk of sulphation. Quickly recharge Save time and increase productivity with less down time thanks to superior charge/discharge efficiency. Extreme heat tolerance Suitable for use in a wider range of applications where ambient temperature is unusually high: up to +60C. Lightweight Lithium batteries provide more Wh/Kg while also being up to 1/3 the weight of its SLA equivalent. Function Support parallel operation
Basic Info. Model NO. LFP51.2-200 Electrolyte LiFePO4 Color as Picture Usage RV/ Marine/ Telecom 5g Station/ Electric Mobility Warranty 3 Year OEM/ODM Acceptable Package Carton and Pallet Lead Time 20-30 Days Dimension 800*500*185mm Transport Package Carton Specification / Trademark PUSTUN Origin China HS Code 8507600090 Production Capacity 5000 Product Description Product Description High Quality 51.2V 200ah Wall Mounted Lithium Battery The battery is a new type of energy storage product, which can be used to provide reliable power supply for various equipment and systems. It is especially suitable for applications with large power, limited installation space, limited bearing capacity and long life.Battery built-in bms battery management system, battery voltage, current, temperature and other information management and monitoring. In addition, the battery pack can balance the charge and discharge of the battery to prolong the cycle life. Multiple battery packs can be parallel to expand capacity and power, parallel to expand capacity and longer power support time requirements. 51.2V Wall mounted series Project Parameters Model 51.2V50Ah 51.2V100Ah 51.2V150Ah 51.2V200Ah 51.2V300Ah Nominal voltage 51.2V Nominal capacity 50Ah (2560wh) 100Ah (5120wh) 150Ah (7680wh) 200Ah (10240wh) 300Ah (15360wh) Dimensions (mm) 500*360*120 570*360*140/ 600*420*210 860*540*160 860*620*200 Weight About 30KG About 53KG About 80KG About 90KG About 120KG Working voltage 45---58.4V Floating charge voltage 54.4---55.2V Equalizing charge voltage 56---58.4V Charging current limiting 10A(The default charging current is greater than 55A, and the current limiting is on) It can be set through the upper computer Standard charging current current 10A 20A 30A 40A 40A Maximum continuous charging current 25A 40A 50A 50A 50A Standard discharge current 17A 33A 50A 66A 80A Maximum continuous discharge current 50A 100A 100A 100A 100A Charging ambient temperature 0~50 �ºC Discharge ambient temperature -20~60�ºC Storage ambient temperature 0~60�ºC Working environment Humidity :â?¤95; Altitude :â?¤4000 Communication mode It has the following communication ports CAN, RS485-1, RS232, RS485-2; CAN and RS485-1 are responsible for communicating with the inverter; RS232 is responsible for the communication with BMS upper computer, and is used as the battery software upgrade interface at the same time; RS485-2 is responsible for parallel communication between batteries. Power display mode LED light / display
Basic Info. Model NO. PST120-12 Installation Packaged Rechargeable Chargeable Color Ivory White Weight 34.5kg Terminal Cooper Case ABS Separator AGM Plate Flat Plate Maintenance Free Sealed Type Glue Sealing Transport Package Carton Then Pallet Specification 407*174*209mm Trademark PUSTUN Origin China HS Code 8507200000 Production Capacity 600PCS/Day Product Description We produce VRLA/SLA Battery, Industrial Battery, 12V Battery, Rechargeable Battery, Gel Battery, Deep Cycle Battery, sealed lead acid battery and so on. GEL Battery for UPS/EPS, Power wheels, Inverters, Off grid solar system, Solar street light, Telecommunication and other electrical D/C power sources. Deep cycle & High performance. Professional 12V120Ah Gel Battery
LiFePO4 Solar Lithium Battery 51.2V 200ah for Solar Storage Ultra-reliable Lithium Iron Phosphate (LiFePO4) technology Integrated battery management System (BMS) Ultra-long cycle life Light weight & compact 1/3 Weight of Lead Acid Water & dust resistant (IP56) Highly durable ABS enclosure Drop-in lead acid replacement Environment friendly: -20�ºC~60�ºC Bluetooth App is optional Built in BMS overall protection 1.Over charged protection 2.Over discharged protection 3.Thermal protection 4.Over current protection 5.Cell balancing
The battery is a new type of energy storage product, which can be used to provide reliable power supply for various equipment and systems. It is especially suitable for applications with large power, limited installation space, limited bearing capacity and long life.Battery built-in bms battery management system, battery voltage, current, temperature and other information management and monitoring. In addition, the battery pack can balance the charge and discharge of the battery to prolong the cycle life. Multiple battery packs can be parallel to expand capacity and power, parallel to expand capacity and longer power support time requirements.
Basic Info. Model NO. PTD250-12 Installation Packaged Rechargeable Chargeable Weight (Kg) 68kg Color Black/Ivory White Terminal Type Lead / Bolt & Nut Safety Explosion-Proof Battery Case ABS Separator AGM Sealed Type Sealed Transport Package Carton / Wooden Case / Pallet Specification 520x268x243 mm Trademark PUSTUN Origin Guangzhou, China HS Code 8507200000 Production Capacity 600PCS/Day Product Description We produce VRLA/SLA Battery, Industrial Battery, 2V/6V/12V Batteries, Rechargeable Battery, Gel Battery, Deep Cycle Battery, sealed lead acid battery and so on. Valve regulated lead acid deep cycle series batteries are designed with AGM (Absorbent Glass Mat) technology, high performance plates and electrolyte to gain extra power output for common power backup system applications. Advanced Features: 1. Environmentally friendly 2. Completely Maintenance-Free 3. Non-Spillable construction design. 4. Wide Operating Temperature Range(-20�°C~+60�°C) 5. Long Life (12-15 years designed life) 6. Explosion Proof 7. Valve Regulated & High Discharge Rate Capability 8. Low Self Discharge 9. Independent of Position 10. Ease of Shipment 11. No need of balanced charge or boost
Product Description Tubular Plate Battery 2V 250AH (OPzS250-2) Specifications The OPzS battery is a traditional tubular plate flooded battery which offers 20 years design life with a cycle life of 1800 cycles at 80% Deep Of Discharge. This range is most suited for all standby power applications that require the highest levels of reliability and security. Characters 1. Use gel electrolyte, with nice performance on wide temperature range, suitable for harsh environments coperation. (-40�º C~60�º C) 2. Made by tubular positive plate materials, monthly self-discharge rateâ?¤ 1.5% 3. Excellent recover ability of Cycling and deep discharge, more than 800 times cycle life at 100% deep discharge, improve the system reliability effectively. 4. Floaing design life time up to 20 years, in the coperation of normal float charging, capacity keeps stable, attenuation rate stays low. Application Wind power system, Solar power system, Emergency lighting alarm systems, UPS(Uninterruptible power sypply) Telecommunications, Telephone exchanges control equipment, EPS instrumentation, Bank ATM System, Medical equipment, Fire and security system and so on. Capacity 77�°F(25�ºC) 100 hours rate(3.00A 1.85V) 300Ah 10 hours rate(25.0A 1.80V) 250Ah 5 hours rate(42.0A 1.80V) 210Ah 3 hours rate(62.5A 1.75V) 187Ah 1 hour rate(132.0A 1.67V) 132Ah Internal Resistance Full charged battery 77�°F(25�ºC):0.0008�© Capacity affected by Temperature (10 hour rate) 104�°F(40�ºC) 102% 77�°F(25�ºC) 100% 32�°F(0�ºC) 85% 5�°F(-15�ºC) 65% Self-Discharge 68�°F(20�ºC) Capacity after 3 month storage 90% Capacity after 6 month storage 80% Capacity after 12 month storage 60% Max discharge current77�°F(25�ºC):1250A(5S) Charge (Constant Voltage) Float:2.23 to 2.27V/77�°F/(25�ºC) Cycle:2.38 to 2.42V/77�°F/(25�ºC) Max Current:25A