1. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 2. CONSTITUTION Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) :
1. About the Manual: The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2. CONSTITUTION: Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly 3. Usage: It is one kind of positive displacement downhole motor, with working principle is to convert the high pressure fluid power of mud into mechanical energy for bit rotation. It is widely used in oil field and mine directional well and horizontal well, cluster Wells and vertical Wells, drilling, deflecting, adjusting azimuth, coring, reaming, side tracking and workover treatment, and also applied in some special operations as compound drilling and traversing, etc. Specifications We can produce series of downhole motors in different sizes, as 57(21/4"),73(23/4"),89(31/2"),95(33/4"),120(43/4"),127(5"),165(61/2"),172(63/4"),178(7"),185(71/4"),197(73/4"),203(8"),216(81/2"),244(95/8"), etc.
1. About the Manual: The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2. CONSTITUTION: Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly 3. Usage: It is one kind of positive displacement downhole motor, with working principle is to convert the high pressure fluid power of mud into mechanical energy for bit rotation. It is widely used in oil field and mine directional well and horizontal well, cluster Wells and vertical Wells, drilling, deflecting, adjusting azimuth, coring, reaming, side tracking and workover treatment, and also applied in some special operations as compound drilling and traversing, etc. Specifications We can produce series of downhole motors in different sizes, as 57(21/4"),73(23/4"),89(31/2"),95(33/4"),120(43/4"),127(5"),165(61/2"),172(63/4"),178(7"),185(71/4"),197(73/4"),203(8"),216(81/2"),244(95/8"), etc.
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
Drilling and civil engineering bentonite is made by API and OCMA standardIt can be used as low solid phase mud in under ground civil engineering and drilling field  The specifications Item Mud  yieldM3T Filter  loss ML30min Yield  1b100ft2 Moisture  Wet Sieve Analysis0074mm gel strength HH01 18 12 3xPV 12 4 18 25 40 HH02 1218 1218 3xPV 12 4 15 20 30
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 3. CONSTITUTION Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly Mud motor, Downhole Motor used for HDD machine Rock conditation Drilling, Rock tools Usage It is one kind of positive displacement downhole motor, with working principle is to convert the high pressure fluid power of mud into mechanical energy for bit rotation. It is widely used in oil field and mine directional well and horizontal well, cluster Wells and vertical Wells, drilling, deflecting, adjusting azimuth, coring, reaming, side tracking and workover treatment, and also applied in some special operations as compound drilling and traversing, etc. A Variof Types &ety the Capabilities In accordance with the actual drilling needs, we push out high, midiem and low speed downhole motors, of a variety of types with different functional configuration and application for all working conditions.
Commodity: Caustic Soda Flakes Caustic Soda Pearls / Bead / Prill / Granule Caustic Soda solid Molecular formula: NaOH Molecule Weight: 40 H.S code: 28151100 CAS: 1310-73-2 UN number 1823 Dangerous Class 8 We use rich natural gas resources and its strategic of liquid alkali procurement, storage, transport conditions, gradually formed transportation and sale of liquid alkali, production and sales base and external processing of flake caustic, solid caustic soda, granular caustic soda, which provide ideal condition and environment for domestic and foreign trade. Typical Specifications: Indexes Purity NaCl Na2CO3 Fe2O3 99 99 0.15 0.9 0.003 98 98 0.15 0.5 0.002 96 96 2.8 0.85 0.005 Used as a raw material in the manufacture of soaps ,detergent, textiles and paper ,and likewise ,in water softening and treatment, drilling mud in oil field, refining petroleum products, and washing beer and soft drink bottles, in food and drug industry ,it is used as acidity regulator, alkali, and so on. Packing :Flake/pearl:25kg/plastic woven bag with PE inner Solid :200kg/ iron drum Loading weight in 1 x 20fcl: 27mt
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 3. CONSTITUTION Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly Mud motor, Downhole Motor used for HDD machine Rock conditation Drilling, Rock tools
1. About the Manual The Lake Drilling MOTOR is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. LAKE MOTORS offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. LAKE MOTORS are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2.Description of downhole motor 1.The down-hole drill motor is a kind of downhole drill tool driven by mud. 2.As mud fluid from the mud pump enters the motor via the bypass valve, a certain pressure difference is formed at the inlet and outlet of the motor, pushing the rotor to rotate. Torque and rotate speed are transferred via the cardan shaft and the driving shaft to the bit. 3. Performance of the down-hole drill motor depends mainly on performance parameters of the screw motor. 4.This product uses the high and new technology of coating to avoid coating off of rotors resulted from the traditional technology. Its strength and life are greatly improved. 5.It is applicable to directional drilling,horizontal drilling, composite drilling, cluster wells, sidetrack wells and well workover etc. 3. Advantage of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
We are supplier and exporter of Hematite Powder. Hematite Powder is a mineral, coloured black to steel. It is mined as a main of iron ore and used as a weighting agent in oil drilling. It is the mineral form of iron(III) oxide (Fe2O3). Fluids weighted with API Hematite Powder contain fewer solids by volume than, making higher mud fluids possible. API Grade Hematite Powder is applicable in all types of drilling fluids, including freshwater, seawater and oil-base muds. It is used as a density increasing product, used as a weighting agent and in the paint industry. Hematite is also a harder mineral than Barite so it is more resistant to particle size degradation. High Density Hematite Powder API Grade -SG = 5.19 - 5.47 -Fe2O3 = 96.70% -Fe = 71.82% -SiO2 = 0.89% -Mesh Size (passing at 98%) = 325
With the help of our team of experts, our company known as a leading Exporter of Drilling Motor in Beijing, Beijing, China.Luhai drilling motor is a positive displacement motor. High pressure drilling fluid flows into the drilling motors, thereby enabling the hydraulic energy to be converted into mechanical energy, at the same time, the rotor drives the shaft and bit to rotate to achieve the purpose of drilling.Luhai produces LZ73, LZ89, LZ95, LZ102, LZ120, LZ127, LZ146, LZ165, LZ172, LZ185, LZ197, LZ203, LZ216, LZ244, LZ286 and other types of drilling motors. They are for drilling diameter of 88.9-660mm. Luhai also design and develop drilling motors with special sizes, different structural features and operating characteristics in accordance with the user's requirements, thus forming different varieties.At present, in addition to ordinary straight drilling motors, Luhai can also provide the following types of drilling motors: 1. Bent drilling motors: The bent angle on the universal shaft can meet different kickoff requirement, there are single-bent and double-bent available. 2.Bent angle adjustable drilling motors: The bent angle of the drilling motors can be adjusted on well surface which enhance the extension of kicking off. 3.Extension drilling motors: On the basis of the ordinary drilling motor, improve motor torque to make the bit drilling quickly by increasing motor stage. 4.Hollow drilling motors: To meet the needs of high flow rate solids carrying in drilling, hollow rotors with carbide nozzles of different sizes are adopted, which can increase the input flow rate and the horsepower of drill bit.. 5.Drilling motors with high kick-off rate: Unique structural design, shorter body, bent point closer to the drill bit, and kick-off rate of up to >1°/m. 6.Saturated saltwater mud-resistant drilling motors: To maintain long time operation of drilling motors in saturated saltwater mud, special rotor coating is adopted to provide better corrosion and wear resistance. 7.High-temperature drilling motors: In order to improve the high temperature resistance of the stator rubber of the drilling motors, to meet the drilling requirements in high geothermal gradient region and deep and ultra-deep well drilling requirements, high-temperature resistant rubber is adopted to increase the temperature resistance of motor above 150ºC. 8.Sealed driving shaft drilling motors: The ordinary mud lubricated driving shaft is replaced with oil lubricated seal driving shaft, which improves the working conditions of the thrust and radial bearings, thus extending the service life of the drilling motors.
1. About the manual The lake drilling motor is a powerful and reliable positive displacement motor. The motor generates an optimum balance of rotational speed and high torque to drive a variety of drill bits at speeds that maximize tool life and performance. Lake motors offers a choice of flow rates, speeds, and torques to match a wide range of operational parameters. Lake motors are used in applications such as straight hole drilling, directional (steerable) drilling, horizontal drilling, hole opening, and re-entry(work over). 2. Advantages of downhole motor Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor.
Couplings, gearbox, valves, pumps, bearings, conveyor systems, pipes & fittings, automation drives electrical items, rtd, cables, switchgears, transformers, measuring instruments, drilling machines. ball valves, gate valves, globe valves, butterfly valves, diaphragm valves, waffle valves, sluice valves, hydraulic valves, pneumatic valves, solenoid valves, bellow seal valves, check valves in stainless steel, ss 304, ss 316, brass, m.s, cast iron, cast steel, pvc, nylon, teflon, ceramic lining valves. fittings: flanges, elbows, tee, couplers, nipples. bearings, v belts, couplings: gear couplings, pin bush couplings,pulleys.Export, clearance, door delivery, import, automations, maintenance, retro fitting, installations
Downhole motor is a kind of downhole dynamic drilling tool upon the power of drilling mud. Mud stream from the outlet of mud pump flows through a by-pass valve into the motor. This stream produces pressure loss at both inlet and outlet of the pump, to push the rotor into rotating, and to transmit the torque and speed onto the bit. The downhole motor property mainly depends upon its property parameters. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 1. Material: High manganese steel 2. Standard: API 3. Features: Big torque, high effective, wide flow rate range, running stable and long using time. 4. Specifications: Fit for 3 1/2"--17 1/2" well hole, including straight body, single- bent and double-bent construction.
All products will be made according to API and related international standard as per customers' requirements. Integral blade stabilizer is an important tool in the drilling engineering to control the well deviation. It can stabilize the drilling tools in the drilling process of oil, gas and geological exploration. It can increase the bit life, drilling speed and well bore quality. There are two kinds of integral stabilizers: spiral integral blade stabilizer and straight integral blade stabilizer. Hardfacing type: HF1000, HF2000, HF3000, HF4000 Send your inquiry message to Anna Zhang in the comments section below:
Main features: 1. You can choose to use a single saw or a double saw for product stability, or a single saw for unstable products 2. Ensure the hygiene of the meat and ensure a smooth cutting surface 3. Waterproof design for quick cleaning 4. According to different uses, frozen meat, lamb chops, steak, fish 5. Adopting human-machine interface and intelligent operation panel 6. 30 sets of memory functions can be set 7. Feeding adopts servo motor, with high precision 8. The conveyor belt can be removed for cleaning Paramters : cutting thickness 1-50mm ,material thickness under 15cm . capacity 8-15times/min ,can adjustable.
1. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 2. CONSTITUTION Downhole motors differ in size and performance characteristics, but they share the same basic components as follows (Fig.1) : Crossover Sub Safety Catch Sub Power Section Coupling Assembly Bearing Assembly
Downhole motor is a kind of downhole dynamic drilling tool upon the power of drilling mud. Mud stream from the outlet of mud pump flows through a by-pass valve into the motor. This stream produces pressure loss at both inlet and outlet of the pump, to push the rotor into rotating, and to transmit the torque and speed onto the bit. The downhole motor property mainly depends upon its property parameters. ADVANTAGES OF DOWNHOLE MOTOR Increased rate of penetration. Better hole deviation control. Reduction in drill string failure rate. Reduction in wear and tear of the swivel, Kelly, and rotary drives. Reduction in fuel cost, since compared to rotary drilling, less energy is required to power a downhole motor. 1. Material: High manganese steel 2. Standard: API 3. Features: Big torque, high effective, wide flow rate range, running stable and long using time. 4. Specifications: Fit for 3 1/2"--17 1/2" well hole, including straight body, single- bent and double-bent construction.
