We offer Affinity Chromatography Resin which designed for capture of high productivity, cost-effective therapeutic monoclonal antibodies (mAb) and Immunoglobulin G. The product combines excellent dynamic binding capacity, pressure/flow performance and alkaline stability up to 100 cycles of 0.1 M NaOH at the most competitive prices.
We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes
Nitrogen - 46% min Moisture - 1% max Biuret - 1% max Prilled - 0.85-2mm Granular - 2-4mm 90-94%min color - Pure White Radiation - Non-Radiactive Free Ammonia - 160pxt ppm max
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Crystals Benzoin Siam Crystals
Damar products is still needed throughout the world, it can have significant impact on price increases. We provide this Damar on an ongoing basis and can serve exports to your country
Damar products is still needed throughout the world, it can have significant impact on price increases. We provide this Damar on an ongoing basis and can serve exports to your country. With quality packaging and production processes, making the products we sell have selling points that are not only economical but also safe. With our full support we help you become an importer of the products we sell.
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
PC/ABS regrind full container available MATERIAL : PC/ABS regrind full container available CATEGORY : PC/ABS TYPE : Regrind GRADE : Black color SPECIFICATION : 1 full container available Origin : Tunisia LOADING WEIGHT : 23 Ton FOB (USD/Ton:) : 850$ - 1000$ Packaging : Jumbo Bag Est. Shipping Time : 15, 30, 45 days
PET Airbag scrap with silicon MATERIAL : PET Airbag scrap with silicon CATEGORY : PET TYPE : Airbag SPECIFICATION : 2 full container available Origin : Tunisia LOADING WEIGHT : 19 Ton FOB (USD/Ton) : 450$ - 550$ Packaging : Jumbo Bag Est. Shipping Time 15, 30, 45 days
2Lians can supply LLDPE product as below: PET Bottle In Bales MATERIAL: LLDPE REPRO PELLET MIX COLOR CATEGORY: LLDPE TYPE: PELLET GRADE: FILM GRADE SPECIFICATION: Lldpe repro pellet made from postindustrial film,origin japan,MFI:1~3,MESH:100 Origin: JP LOADING WEIGHT: 26 FOB (USD/Ton): 720-800
PA66 FR regrind black color Pa6 / pa66 is mainly applied as follows: 1. Improves nylon water absorption and improves size stability of the product. 2. Improved nylon fire resistance to meet the requirements of electronics, electrical, communications and other industries. 3. Improved mechanical strength of nylon to achieve the strength of metal materials, metal replacement. 4. Improves nylon low-temperature resistance and enhanced resistance to environmental stress. 5. Improves nylon wear resistance to meet high wear resistance requirements. 6. Improves nylon antistatic properties to meet its extraction requirements and mechanical applications. 7. Improves nylon heat resistance to adapt to high temperature conditions such as car engines. 8. Reduce nylon cost and improve product competitiveness. Through the above modification, high performance and functionalization of nylon composite materials are realized, thereby promoting the development of industries involving high performance and high quality. MATERIAL : PA66 FR regrind black color CATEGORY : PA66 FG TYPE : Regrind GRADE : Black color SPECIFICATION : GF50. 1 full container available Origin : Tunisia LOADING WEIGHT 23 Ton FOB (USD/Ton) : 750$ - 950$ Packaging : Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS repro pellet mixed color from yoghurt caps HIPS Recycled Pellets Thermoplastics PS has two representatives, GPPS and HIPS. In particular, PS HIPS plastic is the most popular to many advantages and applications. HIPS belongs to the group of hard, transparent resins that are easy to create color, processed by laminating film lamination and easy laminating technology. What is HIPS PLASTIC ? HIPS pellet stands for High Impact Polystyrene. Polystyrene has the chemical formula Polystyrene (C8H8)n which is a long chain hydrocarbon in which alternating carbon centers are attached to the phenyl group (the name given to the aromatic benzene ring). MATERIAL: HIPS repro pellet mixed color from yoghurt caps CATEGORY: HIPS repro TYPE: Pellet GRADE: Mixed color SPECIFICATION: Mixed color.from yoghurt caps Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 900$ - 1150$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
PC Water bottle blue color MATERIAL: PC Water bottle blue color CATEGORY: PC TYPE: Water bottle GRADE: Black color SPECIFICATION: PC water bottle,blue color.15 tons available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 1350$ - 1550$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
ABS REPRO GRAY COLOR MATERIAL: ABS REPRO GRAY COLOR CATEGORY: ABS TYPE: REPRO GRADE: GOOD QUALITY SPECIFICATION: . Gray color . 120 meshi . Impact > 13 . 600kg big bag . Korean origin . Post industrial grade 65 Ton available Origin: SOUTH KOREA - GWANG YANG LOADING WEIGHT: 25 Ton FAS (USD/Ton): 1450$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
PVC Regrind Post Production From Pipe MATERIAL: PVC Regrind Post Production From Pipe CATEGORY: PVC TYPE: REGRIND GRADE: Regrind post production from pipe SPECIFICATION: Color â?? mix. Quantity per container â?? 25 ton. see TDS for further details Origin: Israel - Haifa LOADING WEIGHT: 25 Ton FAS (USD/Ton): 690$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Color index, number : 18 Hot alcoholInsolubile,% : 1.00 Application: 1. The plasticity and castability of heating, combined with its ability to absorb a large amount of infiltrated material, is of great value in the casting industry. 2. The lac resin is non-toxic. Based on the excellent characteristics listed above, the shellac resin is applied to alcohol paints, electrical insulating materials, printing inks, rubber fillers, and its use for oil and acid resistance. 3. Other industries: It has a wide range of important application value in many fields such as medicine, food, cosmetics, chemical industry, metallurgy, machinery, woodware, papermaking, electronics and military industry.
Awesome Resin A16 is one of the best product of Luxury Home Furniture. With this product your room becomes more beautiful and comfortable. Bring this Awesome Resin A16 to your beloved family home, your hotels, appartments, etc!. This Awesome Resin A16 made with a beautiful design with high quality materials that will make your family feel at home for long. This product comes in a variety of colors and sizes
Ideal Resin A18 is one of the best product of Luxury Home Furniture. With this product your room becomes more beautiful and comfortable. Bring this Ideal Resin A18 to your beloved family home, your hotels, appartments, etc!. This Ideal Resin A18 made with a beautiful design with high quality materials that will make your family feel at home for long. This product comes in a variety of colors and sizes.
