8Bar 10Bar 13 Bar Working Pressure Fire Hose Suppliers and Manufacturers

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

"Product name Fire Extinguisher Cylinder Type 0.5kg/0.8kg/1.2kg/1.3kg/1.35kg/Cutomized Material Steel Usage CO2 Fire Fighring Keywords Co2 Fire Extinguisher Color Customer Request Working pressure 150bar"

Items Method ZD500C3 Grease Type Lithium Grease Color Yellow or Blue Texture Smooth and transparent NLGI 3#Thickener Type Lithium base-12-hydroxy Thickener Content 13%-15% Penetration Worked 60 GB/T 269 240-250 Dropping point min GB/T 4929 135-140 Copper Corrosion GB/T 7326 pass Base Fluid Properties Base Fluid Type Mineral Viscosity @40 cst GB/T 265 185 Viscosity @100 cst GB/T 265 12 Pour Point -20 Propertie Great in anti-water; Better mechanical invariability; Better anti-rust; Good oxidation stability; Can take place of calcium base and sodium base greases. This product is made of refined base oil, thickened by fatty acid metallic soap thickener, added with many kinds of additives, for instance, abrasion and extreme pressure resisting, anti-corrosive, antioxidant and rustproof etc.

1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 10 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 11 Built-in BMS management system with comprehensive protection and monitoring control functions 12 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 13 Main control MCU can be centrally controlled and manage peripheral settings (AC charger, inverter, solar charger) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable

Pure Nature Bee Propolis Powder , 7% Flavonoids Bee Propolis Liquid Extract Basic Information Place of Origin: Xuchang Brand Name: Super-Sweet Certification: ISO, GMP, HACCP, Kosher, FDA Model Number: 3001 Minimum Order Quantity: 500kgs Price: 19 Packaging Details: 1kgs/foil bag, 20bags/BOTTLE Delivery Time: 10 working days once we receive your deposit Payment Terms: T/T, Western Union, D/P,, MoneyGram Supply Ability: 360tons Product Description Pure natural propolis extracts propolis powder and propolis liquid wholesale SUPER-SWEET is one of the leading China water soluble propolis extract powder suppliers and manufacturers, our professional factory is able to produce natural and organic propolis with cheap price and high quality. Welcome to wholesale and distribution pure and raw bee propolis, and to buy bulk products from us. 1.Specification available propolis content: 30% to 80%, total flavonids: 5% -13% 2.Main function Improving human immunity, antioxidant and antiviral,Preventing cancer, lowering blood pressure, lowering blood sugar, eliminating inflammation and treating diabetes Moisturizing, skin-whitening, anti-wrinkle, anti-oxidation,Treating stomach ulcers, oral ulcers, cervical erosion 3.Application As active ingredients of product for immune enhancing agent, antioxidant, it is widely used in health industry Mercury (Gn):

317L stainless steel is an austenitic stainless steel that contains a low carbon content and higher amounts of molybdenum and nickel compared to 304 stainless steel. The low carbon content of 317L reduces the risk of intergranular corrosion caused by sensitization during welding or high-temperature exposure. The higher nickel and molybdenum content of 317L provide superior resistance to corrosion in harsh environments, particularly those containing chlorides or other halides. This makes it suitable for use in chemical processing, pulp and paper manufacturing, and oil and gas refining applications. 317L stainless steel offers excellent toughness, strength, and formability, and is easy to fabricate using standard methods. It can be welded using common welding techniques, and is often used to fabricate complex shapes and components. Some of the key properties of 317L stainless steel include: Corrosion resistance: 317L offers superior corrosion resistance in harsh environments, particularly those containing chlorides or other halides. High-temperature resistance: 317L can withstand high temperatures and thermal cycling without losing its corrosion resistance properties. Strength and toughness: 317L offers good strength and toughness, making it suitable for use in demanding applications. Fabricability: 317L is easy to fabricate using standard methods, and can be welded using common welding techniques. Overall, 317L stainless steel is a versatile and reliable material that is well-suited for use in a wide range of applications where superior corrosion resistance and high-temperature performance are required. American Standard: ASTM A240/A240M-20a European Standard: EN 10088-2:2005 Japanese Standard: JIS G4304-2005 Chinese Standard: GB/T 3280-2015 Here are some of the most common international standards for 317L stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A312/A312M: Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM A403/A403M: Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4304: Hot-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:317L stainless steel coil; 317L stainless stee strip;317L stainless stee plate; 317L stainless steel sheets; 317L stainless steel tubes; 317L stainless steel pipe; 317L stainless steel flat; 317L stainless steel bar

Incoloy Alloy 902 is a high-strength, heat-resistant, and corrosion-resistant alloy material with excellent mechanical properties and oxidation resistance. It is an iron-based high-temperature alloy composed of elements such as chromium, nickel, molybdenum, copper, aluminum, titanium, and zirconium. The main features of Incoloy Alloy 902 include: Corrosion resistance: Incoloy Alloy 902 has strong corrosion resistance and can resist the corrosion of many strong acids, alkalis, and saltwater environments. Therefore, it is widely used in the chemical, marine, and petroleum industries. Oxidation resistance: Incoloy Alloy 902 has excellent oxidation resistance and can be used for a long time in high-temperature environments without failure. Therefore, it is widely used in equipment and devices operating in high-temperature oxidation environments. High-strength performance: Incoloy Alloy 902 has extremely high strength and hardness, can withstand high stress and high loads, and is therefore widely used in high-strength fields such as aerospace, nuclear industry, etc. Good machinability: Incoloy Alloy 902 has good machinability and can be formed and processed by various methods such as hot working and cold working, suitable for the manufacture of products in various shapes and specifications. In summary, Incoloy Alloy 902 is an excellent high-temperature alloy material with excellent corrosion resistance, oxidation resistance, and high-strength performance. It is widely used in the manufacture of equipment and devices operating in high-temperature, high-pressure, and corrosion-resistant environments. Incoloy alloy 902 is a nickel-iron-chromium alloy with additions of molybdenum and niobium. Here are some international standards and specifications for this alloy: American standards: AMS 5221, AMS 5223, AMS 5225, AMS 5226, AMS 5230, AMS 5231, AMS 5542, AMS 5676, AMS 5717, AMS 5718, AMS 5719, AMS 5738, AMS 5801, AMS 5803, AMS 5804, AMS 5806, AMS 5580, ASTM B366, ASTM B408, ASTM B564, ASTM B649, ASTM B670, ASME SB-366, ASME SB-408, ASME SB-564, ASME SB-649, ASME SB-670 European standards: EN 2.4665 German standards: DIN NiCr21Mo14W, DIN 2.4665 British standards: BS HR 202 Japanese standards: JIS NW 4990 We can provide the following the form:Incoloy alloy902 coil; Incoloy alloy902 strip;Incoloy alloy902 plate;Incoloy alloy902 sheets; Incoloy alloy 902 tube; Incoloy alloy 902 pipe;Incoloy alloy 902 flat; Incoloy alloy902 bar BS: HR 202/JIS:NW 4990/UNS:N09902/W.Nr:2.4665

Incoloy 903 is a high-temperature alloy material, also known as Inconel 903, which is a kind of nickel-based alloy. It is mainly composed of nickel, chromium, iron, cobalt, copper, titanium, aluminum and other elements. It has good high temperature strength, creep resistance and corrosion resistance, and is widely used in aerospace, petrochemical, energy and other industries under high temperature and high pressure environments. and other fields. Following are some features and applications of Incoloy 903: characteristic High temperature strength: It has good strength and rigidity at high temperature, and can withstand stress and load under high temperature and high pressure environment; Creep resistance: It can be used for a long time without deformation under high temperature and high pressure environment; Corrosion resistance: good corrosion resistance in strong acid, strong alkali and other corrosive media; Machinability: Incoloy 903 can be machined, forged and welded through a variety of processing techniques. The international standards for Incoloy alloy 903 in various countries are as follows: United States: AMS 5800, AMS 5801, AMS 5802, AMS 5803, AMS 5826, ASTM B166, ASTM B408, UNS N19903 Germany: DIN 17742, DIN 17754, W.Nr. 2.4633 United Kingdom: BS HR 6, BS 3076 Europe: EN 10095 We can provide the following the form:Incoloy alloy903 coil; Incoloy alloy903 strip;Incoloy alloy903 plate; Incoloy alloy903 sheets; Incoloy alloy903 tube; Incoloy alloy903 pipe;Incoloy alloy903 flat; Incoloy alloy903 bar BS:HR 5/JIS:NW4893/UNS:N19903/W.Nr:2.4665 Incoloy 903 has a wide range of applications, mainly used in the following fields: Aerospace industry: components such as aero-engines, aero-bearings, gas turbines, etc.; Petrochemical industry: such as chemical reactors, high pressure vessels, steam generators and other equipment; Energy industry: such as nuclear reactor components, heat exchangers, coal-fired power plant boilers and other equipment; Other fields: such as the manufacture of high-temperature valves, heat treatment furnaces, medical equipment, etc.

410 stainless steel is a stainless steel grade produced in accordance with American ASTM standards, which is equivalent to 1Cr13 stainless steel, S41000 (American AISI, ASTM). 0.15% carbon, 13% chromium, 410 stainless steel: good corrosion resistance, machinability, general purpose blades, valves. 410 stainless steel heat treatment: solution treatment (�¢??) 800-900 slow cooling or 750 fast cooling.Features: high strength; excellent machinability; hardening after heat treatment; magnetic; not suitable for harsh corrosive environments. 410 stainless steel is a type of martensitic stainless steel that contains 11.5-13.5% chromium and has excellent corrosion resistance, high strength, and hardness. It is a magnetic material and can be hardened through heat treatment, making it suitable for use in various applications that require high strength and corrosion resistance. Some of the key properties of 410 stainless steel include: Corrosion resistance: 410 stainless steel is highly resistant to corrosion, including water, steam, and chemical environments. However, it is not suitable for use in highly acidic or alkaline environments. Hardness: 410 stainless steel has high hardness and strength, making it suitable for use in applications that require wear and abrasion resistance. Heat treatability: 410 stainless steel can be hardened through heat treatment, allowing for improved strength and hardness. Magnetic properties: 410 stainless steel is magnetic and can be used in applications that require magnetic properties. Some of the common applications for 410 stainless steel include: Cutlery and kitchen utensils Valve components and pump parts Bolts, nuts, and screws Springs and bearings Medical instruments and dental tools Oil and gas equipment Overall, 410 stainless steel is a highly versatile material that is well-suited for use in various applications where high strength, corrosion resistance, and hardness are required. Here are some of the most common international standards for 410 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276: Standard Specification for Stainless Steel Bars and Shapes ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes JIS G4303: Stainless steel bars GB/T 1220: Stainless steel bars We can provide the following the form:410 stainless steel coil; 410 stainless stee strip;410 stainless stee plate; 410 stainless steel sheets; 410 stainless steel tubes; 410 stainless steel pipe;410 stainless steel flat; 410 stainless steel bar General blades, mechanical parts, tableware class 1 (spoon, fork, knife, etc.).

304 stainless steel is a widely used austenitic stainless steel alloy that contains 18% chromium and 8% nickel. It is known for its excellent corrosion resistance, high strength, and good formability and weldability. 304 stainless steel is commonly used in a variety of applications, including kitchen equipment, food processing equipment, chemical processing equipment, heat exchangers, and architectural trim. The composition of 304 stainless steel provides it with excellent corrosion resistance in a wide range of environments, including acidic and alkaline solutions, as well as high-temperature and high-pressure applications. Additionally, 304 stainless steel exhibits good resistance to intergranular corrosion, which can occur in welded parts due to the formation of chromium carbides at grain boundaries. In terms of mechanical properties, 304 stainless steel has a tensile strength of around 515 MPa (75 ksi) and a yield strength of 205 MPa (30 ksi), making it suitable for use in high-stress applications. It also has a high elongation, which allows it to be formed and shaped without cracking or breaking. 304 stainless steel can be easily formed and fabricated using a variety of techniques, including cold and hot working, machining, and welding. It can also be polished and finished to achieve a variety of surface textures and appearances. Overall, 304 stainless steel is a versatile and widely used material that offers excellent corrosion resistance, good strength and formability, and a variety of fabrication and finishing options. The following are some of the commonly used international standards for 304 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10088-3: Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:304 stainless steel coil; 304 stainless stee strip�¯�¼?304 stainless stee plate; 304 stainless steel sheets; 304 stainless steel tubes 304 stainless steel pipe; 304 stainless steel flat; 304 stainless steel bar

904L (N08904, 1.4539) super austenitic stainless steel contains 14.0-18.0% chromium, 24.0-26.0% nickel and 4.5% molybdenum. 904L super austenitic stainless steel is a low carbon high nickel, molybdenum austenitic stainless acid resistant steel. It has very good activation-passivation transformation ability, excellent corrosion resistance, good corrosion resistance in non-oxidizing acids such as sulfuric acid, acetic acid, formic acid, phosphoric acid, and good corrosion resistance in neutral chloride ion-containing media. Excellent pitting corrosion resistance, good crevice corrosion resistance and stress corrosion resistance. It is suitable for sulfuric acid of various concentrations below 70�¯�¿�½?�?�°C, and has good corrosion resistance against acetic acid of any concentration and temperature under normal pressure, and the mixed acid of formic acid and acetic acid. Here are some of the most common international standards for 904L stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes ASTM A312/A312M: Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM B625/B625M: Standard Specification for UNS N08925, UNS N08031, UNS N08034, UNS N08932, UNS N08926, UNS N08354, UNS N08830, and UNS R20033 Plate, Sheet, and Strip EN 1.4539: European standard for austenitic stainless steel with high molybdenum content EN 10028-7: Flat products made of steels for pressure purposes - Part 7: Stainless steels EN 10216-5: Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes EN 10217-7: Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes JIS G4304: Hot-rolled stainless steel plate, sheet and strip JIS G4305: Cold-rolled stainless steel plate, sheet and strip JIS G4312: Heat-resisting steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip GB/T 4237: Hot rolled stainless steel plate, sheet and strip GB/T 24511: Stainless steel and heat-resisting steel plate, sheet and strip for pressure equipments We can provide the following form:904L stainless steel coil; 904L stainless stee strip;904L stainless stee plate; 904L stainless steel sheets; 904L stainless steel tubes; 904L stainless steel pipe;904L stainless steel flat; 904L stainless steel bar

304L stainless steel is a low-carbon variation of the widely used 304 austenitic stainless steel alloy. It contains approximately 18% chromium and 8% nickel and is characterized by its good corrosion resistance, high-temperature strength, and excellent weldability. The "L" in its name stands for low carbon, indicating that it has a lower carbon content than standard 304 stainless steel. The low carbon content of 304L stainless steel provides it with improved resistance to intergranular corrosion and improved weldability, particularly in applications where it may be subject to sensitization, which can cause intergranular corrosion in certain environments. 304L stainless steel is commonly used in applications that require good corrosion resistance and high-temperature strength, including chemical processing equipment, food processing equipment, and heat exchangers. It is also used in architectural trim, dairy and brewery equipment, and pharmaceutical processing equipment. In terms of mechanical properties, 304L stainless steel has a minimum tensile strength of 485 MPa (70 ksi) and a minimum yield strength of 170 MPa (25 ksi), making it suitable for use in applications where high strength is required. Its elongation is typically around 40%, which allows it to be formed and shaped without cracking or breaking. 304L stainless steel can be easily formed and fabricated using a variety of techniques, including cold and hot working, machining, and welding. It can also be polished and finished to achieve a variety of surface textures and appearances. Overall, 304L stainless steel is a low-carbon variation of the widely used 304 stainless steel alloy that offers good corrosion resistance, high-temperature strength, and excellent weldability, making it a versatile material for a wide range of applications. American Standard: ASTM A240/A240M-20a European Standard: EN 10088-2:2005 Japanese Standard: JIS G4304-2005 Chinese Standard: GB/T 3280-2015 Indian Standard: IS 6911:2017 Here are some of the most common international standards for 304L stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes ASTM A312/A312M: Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4304: Hot-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:304L stainless steel coil/strip/plate/sheets/tubes/pipe/flat/bar

316Ti stainless steel is an austenitic stainless steel that is stabilized with titanium, which provides improved resistance to corrosion in high-temperature environments. Compared to standard 316 stainless steel, 316Ti contains a small amount of titanium, which stabilizes the material and prevents sensitization to intergranular corrosion. The addition of titanium also enhances the material's resistance to pitting and crevice corrosion in chloride-containing environments, making it suitable for use in chemical processing, pharmaceuticals, and power generation applications. 316Ti stainless steel has excellent mechanical properties and is easily formable, which allows it to be used in a wide range of applications. It can be welded using common welding techniques, and is often used to fabricate complex shapes and components. Some of the key properties of 316Ti stainless steel include: Corrosion resistance: 316Ti offers superior resistance to pitting, crevice corrosion, and intergranular corrosion in chloride-containing environments. High-temperature resistance: 316Ti can withstand high temperatures and thermal cycling without losing its corrosion resistance properties. Strength and toughness: 316Ti offers good strength and toughness, making it suitable for use in demanding applications. : 316Ti is easily formable using standard methods, and can be welded using common welding techniques. Overall, 316Ti stainless steel is a reliable and versatile material that is well-suited for use in a range of applications where high-temperature corrosion resistance and mechanical strength are required. American Standard: ASTM A240/A240M-20a European Standard: EN 10088-2:2005 Japanese Standard: JIS G4304-2005 Chinese Standard: GB/T 3280-2015 Here are some of the most common international standards for 316Ti stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes ASTM A312/A312M: Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4304: Hot-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip 1) Equipment resistant to sulfuric acid, phosphoric acid, acetic acid, acetic acid; 2) petrochemical; 3) Electromechanical hardware; 4) shipyard; 5) Power plants;

Hastelloy S is a nickel-chromium-molybdenum-tungsten alloy with excellent corrosion resistance in a wide range of aggressive media. It was developed by Haynes International, Inc. and is specifically designed for use in highly oxidizing environments. Hastelloy S offers superior resistance to oxidizing and reducing environments, including hot sulfuric acid, sulfurous acid compounds, and hydrogen chloride gas. It also exhibits excellent resistance to localized corrosion, such as pitting and crevice corrosion, and has good resistance to stress corrosion cracking. Due to its exceptional corrosion resistance, Hastelloy S is widely used in the chemical processing industry, especially for applications involving highly corrosive acids, such as sulfuric acid and phosphoric acid. It is also used in pollution control equipment and in the production of pulp and paper. Hastelloy S can be fabricated using a variety of methods, including welding, forging, and machining. However, it is important to use appropriate techniques and equipment to avoid damaging the material's corrosion resistance properties. Overall, Hastelloy S is a highly reliable and durable alloy that offers exceptional performance in highly corrosive environments. American Standards: ASTM B619: Standard specification for welded hastelloy S tubes ASTM B622: Standard specification for seamless hastelloy S tubes ASTM B626: Standard specification for hastelloy S welded and seamless pipe fittings ASTM B366: Standard specification for hastelloy S welded and seamless fittings ASTM B574: Standard specification for hastelloy S rods and bars ASTM B575: Standard specification for hastelloy S plates, sheets, and strips European Standards: EN 10095: Standard specification for hot rolled, forged, and cold worked hastelloy S plates, sheets, strips, rods, and wires EN 10216-5: Standard specification for seamless steel tubes for pressure purposes - technical delivery conditions - part 5: stainless steel tubes Japanese Standards: JIS NW 0276: Standard specification for hastelloy S plates, sheets, strips, rods, and seamless pipes JIS NW 625: Standard specification for hastelloy S welded pipes Chinese Standards: GB/T 14994: Standard specification for nickel-based hastelloy S welded seamless steel tubes GB/T 15007: Standard specification for nickel-based hastelloy S plates, sheets, and strips GB/T 15013: Standard specification for nickel-based hastelloy S welded and seamless pipe fittings GB/T 14995: Standard specification for nickel-based hastelloy S welded steel pipes GB/T 15014: Standard specification for nickel-based hastelloy S rods and bars. We can provide the following the products:Hastelloy S coil; Hastelloy S strip;Hastelloy S plate; Hastelloy S sheets; Hastelloy S tube; Hastelloy S pipe;Hastelloy S flat; Hastelloy S bar GB/JIS:NW0276/UNS:N06635/W.Nr:2.4687

316L stainless steel is a type of austenitic stainless steel alloy with a low carbon content, making it resistant to sensitization, which is the formation of grain boundary carbides at high temperatures, causing intergranular corrosion. The alloy is commonly used in various industries, including chemical, pharmaceutical, and medical, due to its excellent corrosion resistance and good mechanical properties. The chemical composition of 316L stainless steel typically includes 16-18% chromium, 10-14% nickel, 2-3% molybdenum, and less than 0.03% carbon. The addition of molybdenum provides increased corrosion resistance to pitting and crevice corrosion, making it suitable for use in aggressive environments. 316L stainless steel is known for its high corrosion resistance to a wide range of chemicals, acids, and alkalis, and is particularly resistant to chlorides, making it an ideal material for use in marine environments. It is also known for its excellent high-temperature strength, which makes it suitable for use in high-temperature applications such as heat exchangers. In terms of mechanical properties, 316L stainless steel has a minimum tensile strength of 485 MPa (70 ksi), a minimum yield strength of 170 MPa (25 ksi), and a minimum elongation of 40%, making it a strong and ductile material that can be easily formed and welded. Its resistance to high temperatures and thermal expansion make it ideal for use in high-temperature applications. Overall, 316L stainless steel is a versatile and reliable material that offers excellent corrosion resistance, high-temperature strength, and good mechanical properties, making it suitable for a wide range of industrial applications. American Standard: ASTM A240/A240M-20a European Standard: EN 10088-2:2005 Japanese Standard: JIS G4304-2005 Chinese Standard: GB/T 3280-2015 Indian Standard: IS 6911:2017 Here are some of the most common international standards for 316L stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A276/A276M: Standard Specification for Stainless Steel Bars and Shapes ASTM A312/A312M: Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes ASTM A479/A479M: Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4304: Hot-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following form:316L stainless steel coil; 316L stainless stee strip:316L stainless stee plate; 316L stainless steel sheets; 316L stainless steel tubes 316L stainless steel pipe; 316L stainless steel flat; 316L stainless steel bar

Monel K500 Monel alloy is a high-strength nickel-copper alloy with excellent corrosion resistance. Its main components are nickel and copper, and it also contains a small amount of beneficial elements such as aluminum, iron, and titanium. This alloy not only has corrosion resistance, but also has excellent mechanical properties, high strength, hardness and toughness, and can withstand high temperature, high pressure and corrosion in marine environments. Monel K500 alloy is widely used in marine and subsea oil and gas industry, machinery manufacturing, aerospace and other fields. Compared with other nickel-copper alloys, Monel K500 alloy is more corrosion-resistant. It can resist the erosion of nitric acid, seawater, alkaline solution and other media, and can also maintain stable performance under high temperature and high pressure conditions. Due to its low magnetic properties, Monel K500 alloy is also widely used in the electrical and electronic industries. In addition, it also has good weldability and processing performance, and can be formed and manufactured by various methods such as casting, forging, and cold working, so as to meet the manufacturing needs of complex workpieces in different industrial fields. In general, Monel K500 alloy has good corrosion resistance, high mechanical strength, excellent stability and comprehensive performance, and is a very excellent high-performance alloy material. With the continuous development and innovation of science and technology, Monel K500 alloy has a very broad application prospect in the future, and will bring more benefits to human production and life. American standard designation: UNS N05500, Specifications: ASTM B865, ASTM B164, ASTM B127, ASTM B165, ASTM B564, ASTM B865, ASTM B366, ASTM B865, AMS 4676, AMS 4676, AMS 4677, AMS 4677, AMS 4678, AMS 4678, AMS 4679, AMS 4679. German standard designation: W.Nr. 2.4375, Specifications: DIN 17743, DIN 17750, DIN 17752, DIN 17753, DIN 17754. Japanese standard designation: JIS NW5500, Specifications: JIS G4902, JIS G4903, JIS G4904, JIS G4905, JIS G4906, JIS G4907. Chinese standard designation: NS321, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061. We can provide the following the form:Monel alloyK500 coil; Monel alloy K500 strip;Monel alloy K500 plate; Monel alloy K500 sheets; Monel alloy K500 tube; Monel alloy K500 pipe;Monel alloy K500 flat; Monel alloy K500 bar GB:NS321; JIS:NW5500; UNS:N05500; W.Nr:2.4375

Incoloy Alloy 926 is a super-austenitic nickel-based alloy with high levels of molybdenum, nitrogen, and chromium. It is known for its excellent corrosion resistance in a variety of challenging environments, including sulfuric acid, hydrochloric acid, and seawater. Here is a detailed introduction to Incoloy Alloy 926 and its applications: Incoloy alloy 926 is a super-austenitic nickel-based alloy with high corrosion resistance and excellent mechanical properties at high temperatures. It has a chemical composition of 22% chromium, 25% molybdenum, 6% tungsten, and 0.5% nitrogen, with nickel and iron making up the balance. The alloy also contains small amounts of copper and titanium. Incoloy alloy 926 is known for its excellent resistance to a wide range of corrosive environments, including chloride ion stress-corrosion cracking and pitting and crevice corrosion. It also has good resistance to sulfuric acid and phosphoric acid, as well as seawater and brine solutions. The alloy's high nickel and molybdenum content provides excellent resistance to reducing environments, while its chromium content enhances its resistance to oxidizing environments. In terms of mechanical properties, Incoloy alloy 926 exhibits high strength and toughness, along with excellent weldability and formability. It can be fabricated using a variety of techniques, including hot and cold working, machining, and welding. Due to its excellent corrosion resistance and mechanical properties, Incoloy alloy 926 is commonly used in a variety of industries, including chemical processing, oil and gas, nuclear, marine, and desalination. It is often used in applications involving sour gas environments, such as in the production of oil and gas, as well as in heat exchangers, pressure vessels, and piping systems. The international standards and specifications for Incoloy alloy 926 are as follows: United States: ASTM B649, AMS 5737, AMS 5853, UNS N08926 Europe: EN 1.4529, SEW 400 Germany: DIN 17752, DIN 17754, DIN 17750, W.Nr. 1.4529 We can provide the following the form:Incoloy alloy926 coil; Incoloy alloy926 strip;Incoloy alloy926 plate; Incoloy alloy926 sheets; Incoloy alloy926 tube; Incoloy alloy926 pipe;Incoloy alloy926 flat; Incoloy alloy926 bar BS:NA 25/JIS:SUS 890L/UNS:N08925/W.Nr:1.4529

1. Working pressure 0.09 Mpa 2. Working temperature 250 celsius 3. Temperature lapse rate Less than 12 celsius/24h, feeding temperature more than 120 4. Tank material Q345B, 5/6 mm 5. End enclosure 5/6 mm, flanged flat head 6. Stiffener 6 mm, 4 pcs 7. Heating pipe �?57*3.5 mm, L = 77000/154000 8. Compound manhole DN500 9. Bitumen filling hole DN250 10. Anti-leaking breather valve DN60 11. Overhead nitrogen blanketing valve DN25 12. Sheet gasket PTFE 13. Bitumen protective frame 800*750*150 mm, with bitumen flooding pipe 14. Thermometer 0 to 300 celsius 15. Volumeter Ball floating type 16. Bitumen discharge valve DN80 17. Quick coupling DN80 18. Reserve feeding flange hole DN50/100, 2 pcs 19. Flange hole of bitumen DN50/100 20. Bitumen detecting valve DN25 21. Flange hole of heating pipe DN50, 2 pcs 22. Insulated layer 100 mm, glass fiber wool 23. External close plate 1.5 mm, cold rolled plate 24. Guardrail of ladder W = 400 mm Optional Configurations 1. Recognized register BV or LR 2. Heating system Oil, Flue or Electricity