Brief introduction: 1. Producing procedure: Fiberglass yarn impregnated with epoxy resin etc, and then rolled in wet method, and then dried and consolidated. 2. Characteristics: It has excellent electrical and mechanical properties, low dielectrical loss, no deformation, chemical resistant etc. It can be used as main insulator on H grade dry type transformers, load tap changer, reactor, lightning protector, SF6 Inductor etc. 3. Heat resistance class: F,H
- Material : Solid SS304, SS316, SS316L ( also available in some models with hollow tube) - Shape at top of the spigot: Round/dome top or slopped as shown in the picture) - Also available in Square shape - Spigot no hole in the glass panel. - Spigot with base plate and cover ring - Dimensions: 48 x 155mm, 48*220mm, 48*300mm with base plate. - include the black gasket and stainless steel insert - Mirror polished or satin stainless steel.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
WE ARE SUPPLYING FROM INDIA AND FAR EAST
Epoxy Glass Fiber Winding Tube 360 EPCF52 Description: This product adopts fiber glass yarn that is impregnated with insulation jelly made of epoxy resin and other resins by certain proportion, and then it is rolled in wet method, and dried and finally consolidated by baking. Its heat resistance level is up to Class H, and it also has excellent electrical and mechanical properties, chemical resistance (SF6), low dielectrical loss, no deformation or delamination. It can be used as main insulator on H grade dry-type transformer, load tap changer, electricâ??reactor, lightning arrestor, SF6 inductor, etc. Technical Data Standardï¼?GB/T 5132.1-2009 IEC61212-1:2006 No. Properties Unit Value 360/EPCF52 1 Density g/m1.85-2.00 2 Vertical Bending Strength (normal) MPa 400 3 Axial Compressive Strength MPa â?¥150 4 Parallel Breakdown Voltage (90 â?? of transformer oil) Kv â?¥40 5 Vertical Electrical Strength (90 â?? of transformer oil) 1mm Kv/mm â?¥11.6 6 Surface Voltage Resistance after Wetting kv â?¥12 7 Insulating Electrical Resistance after Wetting Ω â?¥1.0*10^9 8 Dielectric Loss Factor (50Hz) - â?¤0.05 9 Water Absorption ï¼? â?¤1 10 Partial Discharge PC â?¤5 11 Temperature Index - 180
Epoxy Resin
Can supply: PMMA-ACRYLIC MIX COLORS, aprox. 95% STRIPS (LABELS CUT-OFF) EXTRUSION GRADE and aprox. 5% Cuttings White Color From The Production Of Tubs (clean, Without Glass Fiber) Cast Grade. Post industrial. Materials are bulk. Can load bulk in 1x40' Open Top container approx. 20-24 MT. Ready for shipment. Photos are available upon request. If you are interested kindly contact us for more information (price, available quantity etc.). You are welcome to visit our company premises and supervise our materials. Certificate ISO: 9001, ISO: 14001, OHSAS 45001, AQSIQ and CCIC.
Pu foam scrap, memory/ visco foam scrap. rigid foam scrap, pvc foam scrap. pp non woven waste, pvc resin off grade/wet, abrasive garnet, epoxy resin, polyester yarn scrap, raw cotton scrap, quartz ore and sulphur.Distributor of polyurethane trim foam scrap, sulphur, epoxy resin, polyester resin, quartz ore, recycled dacron and abrasive garnet.
Tempered glass, laminated glass, mirror, acid etched glass, fritted glass, float glass, reflective glass, low e glass, patterned glass, glass bottle, glass jar, glassware, glass tube, glass cup.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
Guar Gum Types Food, Feed & Pharma Grades - Various particle sizes (very coarse to very fine). - • Various hydration rates (very slow to very fast). - • Various viscosities (1% solution in water = 50 cps to 7000 cps). - • Special deodourised grades. - • Special low microbiological count grades. Technical Grades Straight Guars: - Various particle sizes (very coarse to very fine). - Various hydration rates (very slow to very fast). - Various viscosities (1% solution in water = 50 cps to 8000 cps). - Special good Dry-Flow (Free-Flow) Guars. - Special Anti-Dusted Guars. Modified Guars and Guar Derivatives: - Fast hydrating / High Viscosity / Diesel Slurriable (particularly suitable for oil, gas and other deep well drilling and EOR operations like polymer flooding / fracturing), - Borated. - Reticulated. - Oxidised. - Depolymerised. - High water absorbance capacity. - Carboxymethyl (Anionic). - Hydroxypropyl (Nonionic). - Hydroxypropyltrimethyl chloride (Cationic). - Hydroxypropyltrimethyl chloride Hydroxypropyl (Cationic, double derivative). - Special good Dry-Flow (Free-Flow) Modified Guars / Guar Derivatives. - Special Anti-Dusted Modified Guars / Guar Derivatives. Guar gum is a fiber from the seed of the guar plant. Guar gum is used as a laxative. It is also used for treating diarrhea, irritable bowel syndrome (IBS), obesity, and diabetes; for reducing cholesterol; and for preventing “hardening of the arteries” (atherosclerosis). In foods and beverages, guar gum is used as a thickening, stabilizing, suspending, and binding agent. In manufacturing, guar gum is used as a binding agent in tablets, and as a thickening agent in lotions and creams. How does it work? Guar gum is a fiber that normalizes the moisture content of the stool, absorbing excess liquid in diarrhea, and softening the stool in constipation. It also might help decrease the amount of cholesterol and glucose that is absorbed in the stomach and intestines. There is some interest in using guar gum for weight loss because it expands in the intestine, causing a sense of fullness. This may decrease appetite. USES: Diarrhea. Adding guar gum to the tube feeding formula given to critical care patients may shorten episodes of diarrhea from about 30 days to about 8 days. High cholesterol. Taking guar gum seems to lower cholesterol levels in people with high cholesterol. Guar gum and pectin, taken with small amounts of insoluble fiber, also lower total and “bad” low-density lipoprotein (LDL) cholesterol, but don't affect “good” high-density lipoprotein (HDL) cholesterol or other blood fats called triglycerides. Diabetes. Taking guar gum with meals seems to lower blood sugar after meals in people with diabetes. By slowing stomach emptying, guar gum may also lessen after-meal drops in blood pressure that occur frequently in people with diabetes. Constipation. Irritable bowel syndrome (IBS).
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
Product of Wings Indonesia Cling glass cleaner is special formulated with SPF( Spot Prevention Formula) that quickly removes stains, without leaving behind watermarks. It is suitable for all kinds of surface, such as wood, glass, plastic, and fiber. Available in 3 refreshing variants : Ocean Fresh Apple Fresh Lemon Fresh
Commodity: Sodium Sulphate anhydrous Product Nature Molecular formula: Na2SO4 Molecular weight: 142.04 Property: white granular crystal or powder Use As filler of detergent, the making of sodium sulphide, water glass, or used in papermaking, glass, dye and used as filler, dyeing auxiliary, laxative, antidote, t also can be used in fiber, leather, metallurgy, enamel and soap. Specifications Item GB6009-2003 Type First grade Result of common product Result of neutral product Na2SO4 99.0 99.20 99 40 Water insoluble matter %0.05 0.02 03 Ca & Mg %(Mg) 0.15 0.02 02 Chloride %(Cl) 0.35 0.23 20 (Fe) 0.002 0.0001 0001 Moisture % 0.20 0.02 02 Whiteness % 82 88 85 Packing and Storage Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg/50KG/1000Kg. Transportation-and harsh rain. Stored in a cool, ventilated, dry place.
Commodity: Synthetic Cryolite Formula: Na3AlF6 M.W.: 209.95 Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively. Specifications: Appearance white powder F 52% min Al 12% min Na 33% max SiO2 0.36% max Fe2O3 0.08% max CaO 0.5% max P2O5 0.03% max SO4 0.6% max H2O 0.4% max Loss on ignition 2 % max Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels. Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.
JHG may produce digital printed glass with Dip-Tech printer, ceramic inks. Our solution enable long-lasting durability, specialized functioinality, and outsanding design capabilities for wide range of printed glass.
JHG offers ideal glass to use protecting the surface of tables and desks with any shape or style. We use the best glass cutters, edger and CNC for all complex shapes, hole locations, and perfect edge work.
JHG solar glass including texture glass and flat glass, it is the nice performance low iron glass with high solar transmittance, and low reflection. After tempered, it will be the ideal choice for photovoltaics, solar thermal collector, and greenhouse. Size Maximum Size:1665*2200mm Minimum Size: 300*300mm Specifiction Main thickness  2-5mm Dimension tolerance ±1.0mm Thickness tolerance ±0.2mm Diagonal tolerance 0.2% Overall bow & 0.2% Iron content 110ppm Solar transmittance  from 91.5-99% (wavelength rang 380-1100mm) Hardness 4H
Hard low E is produced by spraying a chemical material with Tin componds on the melting glass surface to form single layer of compound film with certain low emissivity function. Applicationï¼? Architecture:� curtain wall, facade, windows and doors Home appliance: micro oven, refrigerator Advantage: Improved energy efficiency Less UV Reduced condensation Specification: Glass Thickness: 3.2mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm Max size:� 3300*8000mm Normal size:� 2134x3300mm, 2440x3300mm, Quality Standard: In accordance with CE, GB, AS/NIS 2208-1996
