10 Inch Low Noise Rotary Turntable Bearings Suppliers and Manufacturers

We supply high grade face veneer or core veneer. Wood species available: eucalyptus, acacia, poplar, keruing, okume, birch, pine etc. Our core veneer can be used for commercial grade plywood, film faced plywood, packing plywood. 1.Rotary cut : 1,270 x 640 x 1.0MM, OR 1.7mm 2.Sliced cut: 1270x Width 60mm upward , 0.45mm upwards 3.Thickness Tolerance: -0.03, + 0.05 4.Content Moisture: 18 % max 5.Drying process; Sundry or oven dry. 6.Cutting Process: Rotary Cutting/ Sliced cutting Grade A: 1. Full sheet of same color, no dead knot and small hole. No tear, No Joints 2. Whole piece (no joints) with live knots, limited dead knots, some small holes not more than 2cm in diameter. Also available in mix of grade A and B We can supply in following grade 1Grade A: 100% 2Grade A :90%+ Grade B:10% 3Grade B: 100%

We supply Film Faced Plywood ( Shuttering Plywood) with Original Dynea film red brown, brown film (40/128 grade), 30kg, densified Film Faced (15mm to 12mm),11 ply, 12mm thickness (+/- .5mm), 10-15times repetition, 72Hours WBP Glue (Phenol Formaldehyde). Hot press-40minute heating and cooling cycle. Rubber wood + Poly core: 30Kg: Rubber wood + Full core: 30Kg: Eucalyptus + Full core: 38Kg: Benefits: more usages, more load bearing, less scaffolding, save on labor cost. Origin: India, China

Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)

Apple : Apple is beauty to share, both to lose weight, but also make the skin smooth and soft. Apple is a low-calorie food, every 10 green apple 0 grams only produce 60 kcal calories; apple nutrient soluble, easy to be absorbed by the body, it is "living water," said, is conducive to dissolving sulfur elements, so that the skin lubrication soft The There are copper, iodine, manganese, zinc, potassium and other elements, the human body such as the lack of these elements, the skin will dry, easy to crack, itchy. Vitamin C in the apple is the protective element of the cardiovascular, the health element of the heart disease. Eat more apples than those who do not eat or eat less apples cold risk is lower So, there are scientists and physicians called the apple "all-round health fruit" or called "general practitioner". Air pollution is more serious, eat apples can improve the respiratory system and lung function, protect the lungs from the dust and dust in the air.

Kiwi : The world's largest consumption of the first 26 kinds of fruit, kiwi is the most comprehensive. The content of Vc, Mg and trace elements in kiwifruit fruit was the highest. Among the top three low-sodium and high-potassium fruits, kiwi is at the top of the list because it contains more potassium than bananas and citrus. At the same time, the content of Ve and Vk in kiwifruit was determined to be excellent, low in fat and no cholesterol. According to the analysis, kiwi fruit vitamin content per 100 grams of fresh samples in general 100-200 mg, high up to 400 mg, about 5-10 times the citrus; sugar 8-14%, acid 1.4-2- 0%, but also with tyrosine and other amino acids 12 species. kiwi fruit contains a wide range of nutrients, most of the fruit is rich in one or two nutrients, but each kiwi can provide 8% DV folic acid, 8% DV copper, 8% pantothenic acid, 6% Fresh, 4% DV iron and vitamin B6, 2% DV phosphorus and Va as well as other vitamins and minerals. Kiwi in addition to kiwi alkali, proteolytic enzymes, tannin pectin and sugar and other organic matter, as well as calcium, potassium, selenium, zinc, germanium and other trace elements and the human body needs 17 kinds of amino acids, but also rich in vitamins, , Fructose, citric acid, malic acid, fat. A kiwi can provide a day more than twice the demand for vitamin C, known as the "king of fruit." Kiwi also contains good soluble dietary fiber, as the fruit of the most eye-catching place is contained in its superior antioxidant properties of plant chemical substances sod, according to the US Department of Agriculture research report, kiwi comprehensive antioxidant index in the Fruits among the top, second only to the thorns, blueberries and other small fruit, far stronger than apples, pears, watermelon, citrus and other daily fruits. And blueberries belong to the second generation of fruit is quite representative. Compared with sweet orange and lemon, kiwi fruit contains vitamin C ingredients are two times the first two fruits, so often used to fight against scurvy. Not only that, kiwi can stabilize mood, lower cholesterol, help digestion, prevent constipation, as well as thirst and diuretic and protect the role of the heart.

Diesel En590 10-50-500-5000 And Others Ppm Ultra Low Sulphur. D2 0,2-62 Gost 305-82 Or 0,01 Or 0,05. D2 Automotive Fuel Oil (ago). D6 Virgin Fuel Oil. Hsd Diesel High Speed 500ppm En90. Diesel En590 Euro4 Gost 52368. Pms Premium Motor Spirit Jp54 (ts1) Gost 10227-86. Jet Fuel A1 Gost 10227-86. Marine Fuel Oil Cst 180-280-380. Espo (siberia Pacific Oil) Crude Oil Api 34,7. Lco (light Cycle Oil). Mazut Mt100 Gost 10585-75 And 10585-99. Rebco Gost 51 858-2002/9965-76 Api32/crude Oil 39-1623-93. Lpg 50/50 Propane/butane - 70/30 P/b. Lng 5542-87 By Iso Containers Etc. Gasoline All Types (87-89-92-95). Bitumen/asphalt All Grades. Fertilizers Urea, Dap, Etc Product Description : Petroleum products are materials derived from crude oil (petroleum) as it is processed in oil refineries. ... These fuels include or can be blended to give gasoline, jet fuel, diesel fuel, heating oil, and heavier fuel oils.. Price of product ( USD price or FOB price) : 20.000 MT monthly market price. 100.000 MT monthly market price Less 5%. Product origin : Russia and Non Russia Key Specifications/Special Features : All types/grades of Fuels, Gas, Oil are available for supply. Many commercial names for oils, fuels, gases, etc. are used in the market. To avoid misunderstanding basic details of specifications needed by buyer are mandatory. Specifications for types/grades of products (special grade needed by buyer) will be issued after received your credible purchase request in the form LOI/ICPO docs. Minimum Order Size and Packgaing details : Bulk in tanker vessels. Tanks 20 MT.

Marigolds were first discovered by the Portuguese in Central America in the 16th century. Marigolds are hardy, annual plants and are great plants for cheering up any garden. Broadly, there are two genuses which are referred to by the common name, Marigolds viz., Tagetes and Celandula. Tagetes includes African Marigolds and French Marigolds. Celandula includes Pot Marigolds. Kingdom : Plantae Division : Magnoliophyta Class : Magnoliopsida Order : Asterales Family : Asteraceae Genus : Tagetes, Calendula Marigolds come in different colors, yellow and orange being the most common. Most of the marigolds have strong, pungent odor and have has great value in cosmetic treatment. There are many varieties of Marigolds available today. Some of the major Marigold varieties are listed below: African or American Marigolds (Tagetes erecta): These marigolds are tall, erect-growing plants up to three feet in height. The flowers are globe-shaped and large. Flowers may measure up to 5 inches across. African Marigolds are very good bedding plants. These flowers are yellow to orange and do not include red colored Marigolds. The Africans take longer to reach flowering stage than the French type. French Marigolds (Tagetes patula): Marigold cultivars in this group grow 5 inches to 18 inches high. Flower colors are red, orange and yellow. Red and orange bicolor patterns are also found. Flowers are smaller, (2 inches across). French Marigolds are ideal for edging flowerbeds and in mass plantings. They also do well in containers and window boxes. Signet Marigolds (T. signata 'pumila'): The signet Marigolds produce compact plants with finely divided, lacy foliage and clusters of small, single flowers. They have yellow to orange colored, edible flowers.The flowers of signet marigolds have a spicy tarragon flavor. The foliage has a pleasant lemon fragrance. Signet Marigolds are excellent plants for edging beds and in window boxes. Mule Marigolds: These marigolds are the sterile hybrids of tall African and dwarf French marigolds, hence known as mule Marigolds. Most triploid cultivars grow from 12 to 18 inches high. Though they have the combined qualities of their parents, their rate of germination is low. Marigold (Calendula) is an extremely effective herb for the treatment of skin problems and can be used wherever there is inflammation of the skin, whether due to infection or physical damage; for example, crural ulceration, varicose veins, haemorrhoids, anal fissures, mastitis, sebaceous cysts, impetigo or other inflamed cutaneous lesions. As an ointment, Marigold (Calendula) is an excellent cosmetic remedy for repairing minor damage to the skin such as subdermal broken capillaries or sunburn. The sap from the stem is reputed to remove warts, corns and calluses.

Mace Botanical: Myristica fragrans Family: N.O. Myristicaceae Hindi Name: Mace - Javitri General Description: Nutmeg, spice consisting of the seed of the Myristica fragrans, a tropical, dioecious evergreen tree native to the Moluccas or Spice Islands of Indonesia. Geographical Sources The nutmeg tree, Myristica fragrans, is indigenous to the Moluccas in Indonesia but has been successfully grown in other Asian countries and in the Caribbean, namely Grenada. Banda Islands, Malayan Archipelago, Molucca Islands, and cultivated in Sumatra, French Guiana Composition -> Nutmeg and mace contain 7 to 14 percent essential oil, the principal components of which are pinene, camphene, and dipentene. Nutmeg on expression yields about 24 to 30 percent fixed oil called nutmeg butter, or oil of mace. Dried kernel of the seed. Varieties -> Whole nutmegs are grouped under three broad quality classifications: 1. Sound: nutmegs which are mainly used for grinding and to a lesser extent for oleoresin extraction. High quality or sound whole nutmegs are traded in grades which refer to their size in numbers of nutmegs per pound: 80s, 110s and 130s (110 to 287 nuts per kg), or 'ABCD' which is an assortment of various sizes. 2. Substandard: nutmegs which are used for grinding, oleoresin extraction and essential oil distillation. Substandard nutmegs are traded as 'sound, shrivelled' which in general have a higher volatile oil content than mature sound nutmegs and are used for grinding, oleoresin extraction and oil distillation; and 'BWP' (broken, wormy and punky) which are mainly used for grinding as volatile oil content generally does not exceed 8%. 3. Distilling: poor quality nutmegs used for essential oil distillation.Distilling grades of nutmegs are of poorer quality: 'BIA' or 'ETEZ' with a volatile oil content of 8% to 10%; and 'BSL' or 'AZWI' which has less shell material and a volatile oil content of 12% to 13%. Method of Processing -> When fully mature it splits in two, exposing a crimson-coloured aril, the mace, surrounding a single shiny, brown seed, the nutmeg. The pulp of the fruit may be eaten locally. After collection, the aril-enveloped nutmegs are conveyed to curing areas where the mace is removed, flattened out, and dried. The nutmegs are dried gradually in the sun and turned twice daily over a period of six to eight weeks. During this time the nutmeg shrinks away from its hard seed coat until the kernels rattle in their shells when shaken. The shell is then broken with a wooden truncheon and the nutmegs are picked out. Dried nutmegs are grayish-brown ovals with furrowed surfaces. Large ones may be about 1.2 inches long and 0.8 inch in diameter. Taste and Aroma: Nutmeg has a characteristic, pleasant fragrance and slightly warm taste

Castor meal is also variously called castor meal, castor residue, castor extract & de-oiled castor cake Castor meal - the residue obtained from castor cake by the solvent extraction process - is one of the most versatile natural manures. It is truly organic manure which enhances the fertility of the soil without causing any damage or decay. It is enriched with the three big elements vital and conducive to the proper growth of crops - Nitrogen, Phosphorus and Potassium. It also has traces of nutrients like Manganese, Zinc and Copper, thus making it a balanced fertilizer. Moreover, it helps to neutralize the detrimental effects of chemical fertilizers. Apart from their contribution to Nutrients, they have a number of benefits in agriculture, which none of the synthetic fertilizers or pesticides can offer. They bring in the wonderful molecules that nature has designed to help the plants flourish naturally. They provide slow and steady nourishment, stimulation, protection from soil nematodes and insects; improve yields, and quality of product like taste, flavour, amino acid composition etc. The pressed cake obtained after the expression of castor bean. The solvent extracted cake, although rich in protein cannot be used as cattle fodder because of its toxicity. However, it can be used as a fertilizer. The protein content of castor seed meal varies from 21-48% depending upon the extent of decortications. It has an ideal amino acid profile with moderately high Cystine, mithionine, and isoleucine. But its ant nutritional substances, ricin, ricine and an allergen restrict its use in poultry feed, even at a very low level of inclusion. Castor Cake is an excellent fertilizer because of high content of N (6.4%), Phosphoric Acid (2.55%) and Potash (1%) and moisture retention. There is negative correlation between the contents of ricinine in castor seeds and oil content (r = -0.76). This content of ricinine in castor seed is determined by Agro climatic conditions. Nutrient content of Castor Cake: Organic matter - 75 - 80 %, Nitrogen - 4.0 - 4.5 %, Phosphorous - 1.5 %, Potassium - 1.25 - 1.5 %. It also contains some micro nutrients viz., Calcium, Magnesium, Sulphur, Iron, Zinc, Manganese, Copper etc. A typical composition of castor residue/meal is as follows: Nitrogen - 4% min. approx. Phosphorous - 1% min. approx. Potassium - 1% min. approx. Moisture - 10 - 12 % max. approx. Oil Content - 0.7% max. approx. Advantages: 1. It provides all the major & minor nutrients necessary for better plant growth. 2. It also helps in increasing the nutrient uptake by plants. 3. It improves the soil fertility and productivity. 4. It is known to protect the plants from nematodes and termites. 5. It improves the yield & quality of the farm produce. 6. It improves the physical, chemical and biological properties of soil

We can supply Acetic Acid Industrial Grade and Food Grade. Commodity:Acetic acid. Other name: Glacial acetic acid Molecular formula CH3COOH CAS:64-19-7 EC No.200-580-7 Introduction: Annual capacity of our glacial acetic acid is 350,000.the raw material is methanol.we use a new technical process to produce: Methanol decomposition. the most important characteristic of this way are as following: mild oder; high quality--can reach 99.99%min; low cost--30% lower than oil decomposition and ethanol decomposition way. Specifications: Apha color:

Monocalcium Phosphate (MCP) Feed grade Product Features The purity of the product, calcium and phosphorus ratio appropriate to ensure a higher degree of its biological effects. Phosphorus content greater than 22% of the products, their biological effects better. This unique high-tech companies use technology to make our products crystallization, high purity and its harmful impurities significantly below standards:HG28611997 Drying process advanced products, products with low free water under the premise that the product does not lose crystallization of water, avoid the product in the drying process for the loss of water caused by crystallization of biological effects of the reduction. Specifications Appearance white powder or granule Total P 22%min Ca 13-18% F 0.18% max As 10 ppm max Pb 10ppm max Moisture 4%max Source of OriginRock Packing and Storage Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg. Transportation-and harsh rain. Stored in a cool, ventilated, dry place

- Material: 100Cr6, SKF3, GCr15, SKF3S; - Technical: Seamless , Process: Piercing, Cold Drawing, Spheroidizing Annealing, Annealing etc.; - Size Range: OD 10 ~ 160 mm, Wall thickness: 1~ 25 mm; Length: Customized; - Delivery Condition: (1) +C No heat treatment after the final cold drawing process, (2) +LC After the final heat treatment there is a suitable drawing pass,(3) +SR After the final cold drawing process there is a stress relieve heat treatment in a controlled atmosphere, (4) +A After the final cold drawing process the tubes are annealed in a controlled atmosphere, (5) +N After the final cold drawing operation the tubes are normalized in a controlled atmosphere; - Application: Widely Used in Bearing Industry and Automotive Parts, such as Hydraulic Cylinder Pipe, Steel ball, roller and collar of large machinery bearing, axis of rotation, blade, stator pump, profiling, sleeve, mandril, etc.; - Features: High and uniform hardness and wear resistance, and high elastic limit.

Direct from Kazakhstan Refineries, EN 590 Ultra Low Sulphur Diesel(ULSD) & Jet Fuel A1, tank to tank or CIF transactions are available. Kazakhstan origin with very competitive prices. Also available Azerbaijan origin EN590 10 ppm & Jet fuel A1 from state owned refinery.

Raw Bauxite: Bauxite is a soft, whitish to reddish-brown rock consisting mainly of alumina-bearing hydroxides, oxides of iron, silicon and titanium with impurities of Ca, Mg, Cr, V, P, Ga and other elements. Raw Bauxite is a major source of aluminium. Basic alumina containing minerals of Bauxites are gibbsite Al(OH)3, Boehmite g-AlO(OH) and Diaspore a-AlO(OH). We are a major Raw Bauxite Exporter based in Maharashtra (India) and catering to the diverse demands of several middle and eastern Asian countries. About Raw Bauxite: The processing of Raw Bauxite is done at a number of alumina refineries in the world. Bauxite can be processed at a low-temperature autoclave digestion (145 oC to 155 oC). Raw Bauxite can be used also for sweetening stage and for non-autoclave digestion in agitators (105 oC). About 85% of bauxite mined worldwide is used to produce alumina for refining into Aluminium metal and the balance 15% is processed and value added to make its way to other uses like refractory, chemical, cement, abrasives, etc. Aluminium is possibly the most versatile product with applications in almost every industry. Since Bauxite is the primary source for Aluminium there will always be an ongoing promising demand for the same. Application & Uses of Bauxite: Raw Bauxite is successfully used for metallurgical grade alumina production besides applications in the cement industry, alumina chemical, steel, alum, energy industries, flame-retardants, etc. Bauxite is used in : - Aluminium - Cement - Chemical - Blast Furnaces - Iron/Steel Ladles, etc. Advantages of Artha Bauxite: Artha Mineral Resources has good sources for Gibbsitic Bauxite which requires low digestion temperature (145 oC -155 oC) making it more economical to process. Mines are also in close proximity to all-weather ports which makes it very convenient and cost effective to ship this material.

Fly Ash: Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries. The Major Utilization Areas Of Fly Ash : - Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC). - Part replacement of OPC in cement concrete. - High volume Fly Ash concrete. - Roller Compacted Concrete used for dam & pavement construction. - Manufacture of ash bricks and other building products. - Construction of road embankments, structural fills, low lying area development. - As a soil amender in agriculture and wasteland development. Types of Fly Ash: - According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties. - Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product. - Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash. - Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics. Minimum Order Quantity : 1 container

Oval Shape 10 inch

Hoi An lanterns are product that contain many quintessence made by skilled craftsmans. The frame of the lantern is made from old age bamboo, soaked in salt water for ten days to fight termites, creating certainty. The fabric chosen to be a lamp is usually a silk or non-glossy fabric that has a high elasticity so that when the tension is not torn, it can withstand weather changes when used outdoors.