Accepta 0018 is a high performance cooling water treatment comprising an aqueous blend of corrosion and scale inhibitors scientifically formulated for the treatment and protection of open cooling water circuits operating under softened or low natural hardness water conditions.
Accepta 0018 is specifically formulated for use in base exchange softened water or waters with low natural hardness.
Accepta 0018â??s scale inhibitor properties enable this product to minimise the risk of scale formation due to softener slippage or low levels of natural hardness.
Accepta 0018 also includes a specific non-ferrous metal corrosion inhibitor.
Product Benefits
High performance aqueous blend of corrosion and scale inhibitors designed for use in open cooling water circuits.
Excellent softened water corrosion inhibition.
Very low order of mammalian toxicity.
Environmentally acceptable due to freedom from chromateâ??s and heavy metals.
Additional scale inhibition properties.
Compatible with all other chemicals commonly used in water treatment
Halogen resistant.
Can be dosed directly from the drum for ease of dosing and handling.
Non-ferrous metal corrosion inhibitor.
High calcium tolerance.
Simple test method.
Product Properties
Form: Liquid
Colour: Straw colour
Odour: Barely perceptible
pH: 13.0 -13.5
Water solubility: Miscible
Relative density: 1.20 â?? 1.26
*Full details of the product properties are available in the Safety Data Sheet. See below.
Application & Dosage Information
Accepta 0018 should be proportional to the system make up to ensure a continuous reserve within the system water.
The product can be dosed direct from the drum or pre-diluted in a dosing tank.
It is always advisable to carry out a â??Control Of Substances Hazardous to Healthâ?? (COSHH) assessment before use.
Control
Dosage levels will be dependent upon water quality, system conditions and operational factors. The correct level for your system will be advised by our technical consultant.
A simple test method is available for on-site analysis.
Product features and advantages
Sws191 is one kind of alkalinity antiscalant.
Can be used to control the fouling of membrane separation system and reduce particle clogging.
Can control the formation of calcium carbonate, calcium sulfate, barium sulfate, etc..
It can prevent the scaling of calcium carbonate when lsi reaches 3.
Sws191 applies to all major reverse osmosis membranes.
No adverse effects on the environment, especially suitable for the district where has special requirements on wastewater discharge.
Typical properties
Appearance clear colorless liquid
Specific gravity 1.3-1.35
Ph(5% water solution) 10-11
Odor slight ammonia
Adding and controlling
Sws191 should be continuously added to the last level security filter. This product should be injected into the water supply pipe by diluting water tank or packing barrel. The operation parameters of the specific dosing ratio depends on the water quality and membrane system.You can ask dosing software or technical personnel determined.
Safety
Do not touch eyes and skin.More information please see the msds.
Packing
Conventional packaging for 25kg plastic barrels or ibc barrels. If you have special needs, please contact your sales consultant.
"sulphanil" is an h2s scavenger based on our proprietary chemistry. We have filled patent for the same. Since h2s is dangerous to environment and human personnel our product will help to treat h2s in a safer and cost effective way. Sulphanil is water based product which can easily be disposed after its use.
Properties: this product is light yellow liquid. This product is composed of polyquaternium. It has high efficiency, broad-spectrum, low toxicity, fast efficacy, durability and other characteristics. Slime stripping agent for a wide range of ph value .It still have high lethal in the low temperature. It is an excellent sterilization algicide and slime stripping agent.
Usage: suitable for chemical, oil refining, metallurgy, power plantâ??s circulating chilled waterâ??s sterilization and algae removal and slime stripping.
Packing: using polyethylene plastic packing. A barrelâ??s net weight is 25kg.
Storage conditions: it should be stored in a ventilated and dry warehouse. The storage period is two years.
2484 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
Properties: this product is yellow or light yellow, dark brown, dark gray resin solid, and has strong function of bridging adsorption. During the process of hydrolysis, accompanying physical and chemical processes such as condensation, adsorption, precipitation and so on. The net water effect is obvious and non corrosive for the pipeline equipment. It can effectively support the water chromatophilic substance like ss, cod, bod and arsenic, mercury and other heavy metal ions.
Usage: widely used for drinking water, industrial water and wastewater treatment.
Properties: HPMA is brown yellow transparent liquid and is formed by hydrolysis of maleic anhydride. Its molecular weight is about 300-700. The chemical stability and thermal stability of HPMA is high, low toxicity and harmless, and not easy to be hydrolyzed. Under the conditions of high temperature and high PH, the scale inhibition effect of calcium carbonate is better. So it can be mixed use with organic phosphoric acid and zinc salt crude oil.
Usage: HPMA is widely used as the scale inhibitor in circulation chilled water system, water injection system and low pressure boiler.
Welcome to buy sewage treatment roots blower for aeration from fengyuan, which is one of the best sewage treatment roots blower, backwash roots blower manufacturers and suppliers in china.
Sewage treatment roots blower work principle:
In the pool to set the filler, the oxygenation of the sewage form the bottom, and sewage in the pool body in a flow state to ensure that the sewage and sewage filled in full contact, to avoid the biological contact oxidation pool there is uneven contact with the sewage and filler defects.
Characteristics of sewage treatment roots blower for aeration:
1.Adopting the main and auxiliary tank lubrication according to the situation , not to make lubrication more reliable, and to solve the many problems of grease lubrication, effectively improve the bearing life.
2.Seal structure is reasonable, oil and gas can not enter the case, the output of the gas clean, non-oil and gas.
3.Each blower should be tested in strict accordance with national standards , commissioning qualified to complete machine assembly, to ensure the quality of the blower before leaving the factory.
4.Zhangqiu fengyuan sewage treatment roots blower for aeration casting resin sand technology, quality is fully guaranteed.
5.Sewage treatment roots blower for aeration chassis, wall panels from high-precision digital coordinate boring machine processing, high precision, quality and stability.
Part parameter of sewage treatment roots blower for aeration:
Product advantages of sewage treatment roots blower for aeration:
1.The product easy to maintain and maintain.
2. The product has low noise, easy maintenance and other advantages of late.
3. Fan compact and reasonable, covers an area of small.
4. With low noise, economical and durable, no lubrication, long life, good dynamic balance.
Customers of fengyuan machinery:
Packing and loading of the sewage treatment roots blower :
1. More wide range of ro membrane and variety.
2. Ro membrane material more presion.
3. High dension layer ro membrane flatsheet*sheet polyamide.
4. More professional technique guilde.
5. More quality guarantee.
6. More complete and perfect after sale service
Used range:
Chemical, oil, hospital, water treatment, water purifier, concentration.
KB 207 is a water based, environment safe,
food-grade general purpose cleaner to
penetrate, emulsify and disperse oil, grease,
dirt and grime. Ideal for cleaning walls, floors,
desks, light fixtures, automobiles, painted
woodwork.
Can also be used safely on metal surfaces
such as stainless steel, aluminum, copper and
brass
Application:
Spray, mop, brush wipe, dip method are recommended. Use for mopping,
floors & walls by diluting with water as required depending on surface
condition.
Dosage:
Dilute with water depending on the cleaning work. Can be diluted up to 500
times
Handling & Precaution:
Avoid spills on eyes. Should avoid prolonged contact with skin. May irritate
when exposed for a longer period on certain sensitive skin. Harmful if
swallowed.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged
KB 210 is specially formulated for use in dishwashing
machines. It is food-grade.
KB 210 penetrates, emulsifies and disperses oil,
grease, etc. from kitchen wares to give best results.
Ideal for use in automatic washing machine using
dispensers.
Application:
KB 210 can be directly dispensed into washing machine using
regular dispenser or may be added manually as required. Dipping
method is recommended for manual use.
Dosage:
Dilute with water depending on the cleaning work. Adjust
dispensing quantity as per volume and quantity. Use higher
concentration if result is not satisfactory
Handling & Precaution:
Avoid spills on eyes. Should avoid prolonged contact with skin.
Harmful if swallowed.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
LC 101 is used in steam boiler systems where water is
zeolite softened or in natural waters very low in
hardness. This treatment will prevent scale formation
from residual hardness in addition to conditioning sludge.
LC 101 is a balanced blend of polymers which are mildly
alkaline scale and corrosion inhibitors in addition to
sodium sulfite for added pitting and corrosion protection.
If 20 to 30 ppm (mg/l) of sulfite cannot be maintained
with a normal dosage of LC 101, add LC 102 to hold this
recommended level.
Application:
Easily fed to the boiler as a slug dosage or by chemical proportioning pump
directly in to the boiler. It can also be injected into the feedwater tank.
Formula LC 101 contains no heavy metals.
Dosage:
Initial dosage is one (1) quart per 1,000 gallons and one (1) quart thereafter
for every 800 gallons of make-up water. Maintain 20-30 ppm (mg/l) of
orthophosphate in the boiler water.
Handling & Precaution:
Wear protective clothing and eye protection should be provided and worn. In
case of skin contact, immediately flush thoroughly with plenty of clean water.
In case of eye contact, flush with copious of amounts of water for 15 minutes
and obtain immediate medical attention.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
LC 105 is an ideal one product boiler internal treatment. It
can control not only calcium carbonate & calcium
phosphate deposits but also calcium sulfate and barium
sulfate. Highly concentrated alkaline product. Eliminates
excessive precipitation of solids and reduces sludge
accumulation.
Application
For use with make-up water with hardness below 150 ppm and effectively
disperses iron oxides as well as calcium phosphate and clay. Injected directly
into the boiler by means of a proportioning pump. It is environmentally safe,
non-hazardous and non-corrosive.
Dosage
Initial : 2 quarts per 100 gallons or 1 : 200
Maintenance: 1 quart for every 100 gallons of make-up water or 1 : 400
Maintain 15-25 ppm (mg/l) of orthophosphate in the boiler waters with pH
between 11.0 – 12.0. Maintain Conductivity below 5000 µmho/cm. Consult
LifeChem Technical Services when Hardness is low or high.
Handling & Precaution
LC 105 is an alkaline product and should be handled with care to prevent
personal injury. Wear protective clothing and eye protection. In case of
contact with skin, immediately flush with water. In case of contact with eye,
flush with water for 15 minutes and obtain immediate medical attention. Triple
rinse used cans before reuse or disposal.
Packaging
Available in pail of 20 lt. Can also be custom packaged.
LC 230 is a strong descaler with a special blend of
acids, corrosion inhibitors, emulsifiers & dispersing
agents. It effectively removes rust, oxides of metals,
scale and soil from metal and concrete surfaces. It’s
dissolving action on rust, silica and scale is quick and
thorough. Its acid formulation dissolves lime, scale and
rust right down to the base metal or concrete with the
selective inhibitor protecting metal surfaces. Not for
materials like glazed tiles and glass.
Application
Brush or spray on surfaces. Clean surface free from excess rust, soil and
dirt. Apply LC 230. Allow to stand for 10-20 minutes, then wipe off with
water. Surface may require repainting if necessary.
Dosage
For descaling purposes, dilute one part LC 230 with up to 20-100 parts of
water depending on the thickness scales. Allow standing for several hours
and/or re-circulate using pumps. Flush with water until all the scale is
removed. Repeat if scale is still present; check pH and maintain below 1.5
during circulation for control. Use LifeChem LC 240 for neutralizing the spent
solution before disposal. Contact Field Chemist for further information.
Handling & Precaution
Irritating to eyes and skin. If contact with skin occurs, wash immediately
with plenty of water. In case of eye contact irrigate thoroughly with water for
at least 15 minutes. Seek medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Application LC 231 is a special blend of volatile acids,
corrosion inhibitors & dispersing agents. It effectively
removes scale and soil of carbonate nature from metal
and other surfaces. LC 231 is an excellent additive for
the LC 233 for the initial removal of the carbonate based
scale and effectively bring down cost by reducing the
amount of other descalers. Its acid formulation dissolves
lime scale and rust deep down with the selective inhibitors
protecting metal surfaces.
Application
Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply
LC 231. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat
and then flush off with water. Flush with water until all scale is removed. Add
with other descaler like LC 232 & LC 233 for stubborn and difficult to remove
scales. Cannot be used alone.
Dosage
Dilute one part of LC 231 with up to 10 parts of water depending on the
thickness of scales.
Handling & Precaution
Irritating to eyes and skin. Protective clothing and eye protection should be
provided and worn. After contact with skin, wash immediately with plenty of
water. In case of eye contact irrigate thoroughly with water for at least 15
minutes. Seek medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 232 is a very strong concentrated descaler, specifically
designed to remove silica based scales and other stubborn
scales. It is a special blend of volatile acids, corrosion inhibitors
& dispersing agents. It effectively removes stubborn silica scale
and soil of silicate/phosphate nature from metal and other
surfaces. LC 232 is an excellent additive for the LC 231 & LC
233 for additional effectiveness against silica based scales and
effectively bring down cost by reducing the amount of other
descalers. Its special formulation dissolves scale and rust deep
down with the selective inhibitors protecting metal surfaces.
Application
Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC
232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and
then flush off with water. Flush with water until all scale is removed. Add with other
descaler like LC 231 & LC 233 for stubborn and difficult to remove scales. For best
results use circulation or dipping method use of passivating agent like LC 252 or
LC 253 is essential. Make test strip before use. NOT TO BE USED ON
GLASS/SILICATE BASED SURFACES.
Dosage
Dilute one part of LC 232 with up to 10 parts of water or depending on the
thickness of scales.
Handling & Precaution
Irritating to eyes and skin. Protective clothing and eye protection should be
provided and worn. After contact with skin, wash immediately with plenty of water.
In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek
medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 233 is a special blend of non-volatile acids,
corrosion inhibitors, emulsifiers & dispersing
agents. Effectively removes rust, scale and soil
from metal and concrete surfaces.
Application
May be sprayed or brushed on surfaces. Clean surface free from rust, soil
and dirt. Apply LC 233. Allow to stand for 10 - 20 minutes, then wipe off with
water. Dry surface can be repainted if desired for longer protection
Dosage
For descaling of condensers, dilute one part of LC 233 with upto 10 parts of
water depending on the thickness of scales. Allow to stand for several
hours. Flush with water until all scale are removed from condensers.
Handling & Precaution
Irritating to eyes and skin. After contact with skin wash immediately with
plenty of water. In case of eye contact irrigate thoroughly with water for at
least 15 minutes. Seek medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 202 is a water based general purpose cleaner to
Penetrate, emulsify and disperse oil, grease, dirt and grime
And other types of soils from a variety of hard surfaces.
Ideal for cleaning walls, floors, desks, light fixtures,
Automobiles, painted woodwork. Also can be used on metal
Surfaces such as stainless steel, aluminum, cooper and
Brass.
Application
Spray, mop, brush wipe, dip method are recommended. Use for cleaning
Walls, floors, desks, light fixtures, automobile, painted wood work.
Dosage
Dilute with ratio of 1 : 15 (min) up to 1 : 200 with water depending on the dirt
Thickness & type of the surfaces
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with skin. Can
Irritate when exposed for a longer period. Harmful if swallowed.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 219 is a technical specialty cleaner designed to remove difficult deposits
& residue on glass surfaces arrising from long exposure to external weather
Conditions. The stains & marks, including dried fungus generally builds up on
Exposed glass surfaces can easily be removed using lifechem’s lc 219. It
Is a technical product & requires complete attention to the “guidelines on
Application” during it’s use. Lc 219 effectively removes the stains & deposits
Which is generally not removed by standard glass cleaners. It leaves glass
Sparkling clean, smear-free.
The anti static components repel tiny dust particles and thus reduces
Deposits efficiently. Use lifechem’s lc 203 ; glass cleaner regularly to keep
Your glass surface in a sprkling condition.
Application
1. Use undiluted or diluted product as required depending on the stains &
Deposits. A small test patch must be made to select dilution.
2. Damp a piece of clean white wiping cloth with lc 219 and squeeze out any
Extra liquid to avoid spreading & flowing during wiping.
3. Spread a this layer using the damp/wet cloth on the stained glass or mirror
Surface. Select only a small area depending on drying rate.
4. Wipe-off using a separate piece of clean, white cloth to a shining lusture. A
Soaking time may be required in some cases.
5. Use lc 203 to rinse the cleaned surface using glass-wiper in the usual
Method.
6. Leave it to dry.
7. Repeat if necessary for highly soiled stains, deposits etc.
8. Never be used on coated glass unless proved to be safe after testing.
Dosage
May be used undiluted or may be diluted to suit method of application and extent
Of contamination. Suggested dilution is 2:1 or 1:1. Use clean & softened
Water only. Un attended application may result into damage.
Handling & precaution
Avoid spill & stains of lc 219 on ceramic tiles, glass as prolonged exposure to
Lc 219 direct effect. Keep away from children.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 250 is a water displacing anti corrosion compound
Used to prevent rust on metal surfaces with unlimited
Applications in the fields of marine, automobile, aviation
Farming, etc.
Lc 250 creeps along surfaces and into cracks to
Lubricate, loosen frozen parts and displace water. The
Loosened rust can easily be removed. The displacing
Mechanism works by preferential wetting. The attraction,
Of the preventative that of water, thus displacing water.
Application
Apply lc 250 to metal surfaces either by brushing or dipping.
When dipping is used, allow excess chemical to drip prior to
Storage.
Handling & precaution
Avoid unnecessary skin contact. Prolonged contact may cause
Irritation.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
2484 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
