Application LC 231 is a special blend of volatile acids,
corrosion inhibitors & dispersing agents. It effectively
removes scale and soil of carbonate nature from metal
and other surfaces. LC 231 is an excellent additive for
the LC 233 for the initial removal of the carbonate based
scale and effectively bring down cost by reducing the
amount of other descalers. Its acid formulation dissolves
lime scale and rust deep down with the selective inhibitors
protecting metal surfaces.
Application
Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply
LC 231. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat
and then flush off with water. Flush with water until all scale is removed. Add
with other descaler like LC 232 & LC 233 for stubborn and difficult to remove
scales. Cannot be used alone.
Dosage
Dilute one part of LC 231 with up to 10 parts of water depending on the
thickness of scales.
Handling & Precaution
Irritating to eyes and skin. Protective clothing and eye protection should be
provided and worn. After contact with skin, wash immediately with plenty of
water. In case of eye contact irrigate thoroughly with water for at least 15
minutes. Seek medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 232 is a very strong concentrated descaler, specifically
designed to remove silica based scales and other stubborn
scales. It is a special blend of volatile acids, corrosion inhibitors
& dispersing agents. It effectively removes stubborn silica scale
and soil of silicate/phosphate nature from metal and other
surfaces. LC 232 is an excellent additive for the LC 231 & LC
233 for additional effectiveness against silica based scales and
effectively bring down cost by reducing the amount of other
descalers. Its special formulation dissolves scale and rust deep
down with the selective inhibitors protecting metal surfaces.
Application
Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC
232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and
then flush off with water. Flush with water until all scale is removed. Add with other
descaler like LC 231 & LC 233 for stubborn and difficult to remove scales. For best
results use circulation or dipping method use of passivating agent like LC 252 or
LC 253 is essential. Make test strip before use. NOT TO BE USED ON
GLASS/SILICATE BASED SURFACES.
Dosage
Dilute one part of LC 232 with up to 10 parts of water or depending on the
thickness of scales.
Handling & Precaution
Irritating to eyes and skin. Protective clothing and eye protection should be
provided and worn. After contact with skin, wash immediately with plenty of water.
In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek
medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 233 is a special blend of non-volatile acids,
corrosion inhibitors, emulsifiers & dispersing
agents. Effectively removes rust, scale and soil
from metal and concrete surfaces.
Application
May be sprayed or brushed on surfaces. Clean surface free from rust, soil
and dirt. Apply LC 233. Allow to stand for 10 - 20 minutes, then wipe off with
water. Dry surface can be repainted if desired for longer protection
Dosage
For descaling of condensers, dilute one part of LC 233 with upto 10 parts of
water depending on the thickness of scales. Allow to stand for several
hours. Flush with water until all scale are removed from condensers.
Handling & Precaution
Irritating to eyes and skin. After contact with skin wash immediately with
plenty of water. In case of eye contact irrigate thoroughly with water for at
least 15 minutes. Seek medical advice.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 202 is a water based general purpose cleaner to
Penetrate, emulsify and disperse oil, grease, dirt and grime
And other types of soils from a variety of hard surfaces.
Ideal for cleaning walls, floors, desks, light fixtures,
Automobiles, painted woodwork. Also can be used on metal
Surfaces such as stainless steel, aluminum, cooper and
Brass.
Application
Spray, mop, brush wipe, dip method are recommended. Use for cleaning
Walls, floors, desks, light fixtures, automobile, painted wood work.
Dosage
Dilute with ratio of 1 : 15 (min) up to 1 : 200 with water depending on the dirt
Thickness & type of the surfaces
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with skin. Can
Irritate when exposed for a longer period. Harmful if swallowed.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 219 is a technical specialty cleaner designed to remove difficult deposits
& residue on glass surfaces arrising from long exposure to external weather
Conditions. The stains & marks, including dried fungus generally builds up on
Exposed glass surfaces can easily be removed using lifechem’s lc 219. It
Is a technical product & requires complete attention to the “guidelines on
Application” during it’s use. Lc 219 effectively removes the stains & deposits
Which is generally not removed by standard glass cleaners. It leaves glass
Sparkling clean, smear-free.
The anti static components repel tiny dust particles and thus reduces
Deposits efficiently. Use lifechem’s lc 203 ; glass cleaner regularly to keep
Your glass surface in a sprkling condition.
Application
1. Use undiluted or diluted product as required depending on the stains &
Deposits. A small test patch must be made to select dilution.
2. Damp a piece of clean white wiping cloth with lc 219 and squeeze out any
Extra liquid to avoid spreading & flowing during wiping.
3. Spread a this layer using the damp/wet cloth on the stained glass or mirror
Surface. Select only a small area depending on drying rate.
4. Wipe-off using a separate piece of clean, white cloth to a shining lusture. A
Soaking time may be required in some cases.
5. Use lc 203 to rinse the cleaned surface using glass-wiper in the usual
Method.
6. Leave it to dry.
7. Repeat if necessary for highly soiled stains, deposits etc.
8. Never be used on coated glass unless proved to be safe after testing.
Dosage
May be used undiluted or may be diluted to suit method of application and extent
Of contamination. Suggested dilution is 2:1 or 1:1. Use clean & softened
Water only. Un attended application may result into damage.
Handling & precaution
Avoid spill & stains of lc 219 on ceramic tiles, glass as prolonged exposure to
Lc 219 direct effect. Keep away from children.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
2507 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
Lc 250 is a water displacing anti corrosion compound
Used to prevent rust on metal surfaces with unlimited
Applications in the fields of marine, automobile, aviation
Farming, etc.
Lc 250 creeps along surfaces and into cracks to
Lubricate, loosen frozen parts and displace water. The
Loosened rust can easily be removed. The displacing
Mechanism works by preferential wetting. The attraction,
Of the preventative that of water, thus displacing water.
Application
Apply lc 250 to metal surfaces either by brushing or dipping.
When dipping is used, allow excess chemical to drip prior to
Storage.
Handling & precaution
Avoid unnecessary skin contact. Prolonged contact may cause
Irritation.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Kb 236 is a special blend of mineral acids,
Corrosion inhibitors, emulsifiers & dispersing
Agents. Effectively removes rust, scale and soil
From metal and other hard surfaces.
Application
May be sprayed or brushed on surfaces. Clean surface free from
Rust, soil and dirt. Apply kb 236. Allow to stand for 5 - 15 minutes,
Then wipe off or flush with water. Dry surface can be repainted if
Desired for longer protection.
Dosage
For cleaning surfaces, dilute one part of kb 236 with up to 10
Parts of water depending on the thickness of scales, soil & dirt.
Allow to stand. Brushing may be required. Flush with water until all
Scale are removed
Handling & precaution
Acidic product. Irritating to eyes and skin. After contact with skin
Wash immediately with plenty of water. In case of eye contact
Irrigate thoroughly with water for at least 15 minutes. Seek medical
Advice
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Remove impurities in the form of carbon from the surface of the oven, cooking utensils, sewer, ventilation, and other places where carbon deposition thickness is usually attached.
Lc 106 is an ideal steam line anti corrosion treatment for
Boilers. It is a highly concentrated, alkaline product.
Eliminates corrosion in the outgoing steam lines and
Stabilizes ph in the condensate.
Application
For use with boilers which requires anti-corrosion treatment in the steam lines. It
Disperses with steam and forms a protection film on the inner surfaces of the
Steam pipes. Injected directly into the boiler by means of a proportioning pump.
It is environmentally safe. Do not use in boilers where steam
Contacts food.
Dosage
Initial : 1 quarts per 100 gallons or 1 : 400
Maintenance: 1 quart for every 200 gallons of make-up water or 1 : 800
Maintain ph of 7.5 – 8.5 in the steam line of system. Maintain sulfite of 30 – 60
Ppm along with lc 106. Maintain the conductivity less than 5000 mho/cm.
Handling & precaution
Lc 106 is an alkaline product and should be handled with care to prevent
Personal injury. Wear protective clothing and eye protection. In case of contact
With skin, immediately flush with water. In case of contact with eye, flush with
Water for 15 minutes and obtain immediate medical attention. Triple rinse used
Cans before reuse or disposal.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 121 is specially formulated for large installations and
High hardness water. It is developed for effective,
Economical cooling tower treatment at hospitals, hotels,
Large apartment houses, office buildings and other
Industrial and institutional cooling installations. Also
Recommended for a small installations with high
Hardness make-up water. It contains no phosphates,
Chromate, zinc or other chemicals that cause pollution
Problem. Helps control mineral deposits, sludge and
Surface pitting and does not stain automobiles or
Buildings.
Application
Use a reliable automatic proportioner with timer for controlled dosage.
Directly inject in to the circulating pipe upstream from the condenser. Cycles
Of concentration will vary from 5 – 20 as a probable upper limit. For higher
Limits consult our laboratory.
Dosage
Initial treatment : add 1 gallon of lc 121 per 2, 000 gallons of re-circulating
Water. Maintenance treatment : 1 gallon per 6, 000 gallons of water lost to
Bleed off.
Handling & precaution
Wear protective clothing and eye protection should be worn. In case of skin
Contact, immediately flush thoroughly with plenty of clean water. In case of
Eye contact, flush with copious of amounts of water for 15 minutes and
Obtain immediate medical attention. Refer to msds for more specific
Directions.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
Lc 126 condenser water treatment does not use sodium
Chromate, zinc or other toxic chemicals in its composition. It
Eliminates the serious pollution problems usually associated
With the use of such chemicals for corrosion and scale
Control in cooling system. It protects medium size cooling
Towers against scale, sludge and corrosion. Lc 126
Contains a special anti-foulant additive to reduce
Accumulations of mud and silt in condenser tubes. Ideal for
Average towers with 75 to 500 ton capacity.
Application
Formulated for use in open re-circulating cooling water systems found in air
Conditioning and process operations. Apply manually, directly to the cooling
Tower basin.
Dosage
Initial dosage : add 1 gallon of lc 126 for every 500 gallons of system
Capacity.
Maintenance dosage : add 1 gallon of lc 126 for every 1, 000 gallons of
System water lost to bleed off from the cooling tower system
Handling & precaution
Slightly alkaline aqueous solution. Keep out of reach of children. Refer to
Material safety data sheet for more specific procedures and directions.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 141 is single product treatment designed to prevent
Scale deposits and corrosion to ferrous and non-ferrous
Surfaces in hot water heating systems and chilled closed
Loops. It passivates the surfaces and forms a barrier layer to
Inhibit corrosion. It is a synergistic combination of
Phosphonates, polymers and phosphate.
Application
Easily feed/injected directly into the system by means of a chemical by
Pass feeder.
Dosage
Initial treatment is 1 gallon per 1, 000 gallons of water in the system. There
After add lc 141 to maintain a level of 25-35 ppm (mg/l) of
Orthophosphate.
Handling & precaution
It is highly alkaline and should be handled with care to prevent personal
Injury. Protective clothing and eye protection should be provided and worn.
In case of skin contact , immediately flush thoroughly with plenty of clean
Water. In case of eye contact, flush with copious amounts of water for 15
Minutes and obtain immediate medical attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 143 is specially formulated for use in systems that are
Constantly exposed to air, such as vented air to pressurized
Systems providing corrosion protection even in systems that
Are not tight. It reduces maintenance costs by keeping
Exchangers, air handling units and zone valves free of
Corrosion clogs. It also reduces corrosion insulation and
System damage. Lc 143 contains boron nitrate that protects
Against oxygen and acid attack, works well in any closed
System. Recommended for any hot water boiler or recirculating
Or closed loop system.
Application
Can be added to a system either manually or with a pot feeder. If the
Treatment dosage is less that the capacity of feeder, fill up the feeder with
Tap water to prevent air on treatment. Not to be used in electric
Steam boilers.
Dosage
For chilled water circulating system : for initial or maintenance treatment,
Add 1 gallon of lc 143 for each 200 gallons of chilled water. The treatment
Level is easily tested with the drop titration nitrite test kit.
Handling & precaution
Irritant. Avoid contact with eyes. Avoid repeated or prolonged contact with
Skin. If contact occurs, flush with water. If eye contact occurs, flush with
Water for 15 minutes. Seek medical attention. Keep out of reach of
Children. Refer to material safety data sheet for more specific procedures.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 144 is formulated to prevent and reduce scale,
Rust, corrosion and sludge in generator system. It is
The most effective coolant for generator and other
High temperature systems. Lc 144 is a special blend
Of selective glycols, anti-corrosion additives and
Sludge conditioners that provide smooth running of
The systems.
Application
Lc 144 is widely used in power plants, generator system, etc... Found in
Marines, aviations, industries, automotives, industries, hospitals, etc.
Benefits
? excellent protection
? no more severe
Damages
? non-flammable
? non-polluting
? non-corrosive
? non-toxic
? completely safe to
Use
? reduces costly
Maintenance
Dosages
1. Check incoming water source for total hardness and chloride.
2. Recommended total hardness below 30 ppm and chloride below 50
Ppm.
3. Lc 144 can be diluted at a ratio of 1:1, 1:5, 1;10, 1:32 with deionised
Water (recommended).
4. Repeat application monthly or quarterly depending on application.
Flush if colour changes or becomes cloudy.
Handling & precaution
For professional use only. To be used in well ventilated environment. In
Case of contact with eyes, rinse thoroughly with water and seek medical
Advice immediately. If swallowed, take plenty of water and seek medical
Advice immediately. Avoid prolonged contact with skin. Put on gloves for
Sensitive skin. Keep out of reach of children. Additional information may
Be obtained from material safety data sheet (msds).
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 235 is designed specially for use in systems where
The use of acidic descalers are not recommended. Lc
235 may be re-circulated by means of a high volume
Pump for the removal of scale. Lc 235 can be used
Safely on to copper & brass surfaces besides being very
Effective in steel system.
Application
Lc 235 may be soaked overnight and re-circulated. When scale is present,
The tubes should first scraped out to remove as much as possible and then
Flushed out with a hose.
Dosage
Circulate a 10% solution (10 gallons of lc 235 for every 100 gallons of
Water.) for a period of four to six hours depending on the scale thickness.
Solution may be heated for effectiveness by steaming. The system should
Then be drained and inspected. If more scale remains, repeat the process.
When the cleaning process is complete, flush with clean water and place it
Back in service. For storing / stand by system use lc 253 or lc 252.
Handling & precaution
This product is alkaline and should be handled with care to prevent personal
Injury. Protective clothing, gloves and eye protection should be worn. In case
Of skin contact, immediately flush thoroughly with plenty of clean water. In
Case of eye contact, flush with copious amounts of water for 15 minutes and
Consult a physician. Refer to material safety data sheet for more specific
Procedures and directions.
Packaging
Available in pail of 20 lt..
Lifechem lc 306 is a solvent based wet look coating for all types
Of hard and porous surfaces including granite, marble & sand
Stone. Lc 306 penetrates into the tiny pores of the surface
Structure and the minute crevices helped by the selected
Penetrants. The volatile solvents evaporates to leave an inert,
Transparent residue that makes the wet look. The surface is
Shining and polish-able, washable and ready after at least 48
Hours. Lc 306 is comprised of volatile hc solvents, penetrants
And levelling agents designed to provide excellent penetration
And wet look. Lc 306 is ideal for providing and inert coat on
Porous materials like granite, marbles, tiles and such surfaces
Including walls, floors, desks, fixtures, woodwork and even
Paper & paper based products.
Application
Applied by spray, mop, brush wipe, dip after mixing the catalyst in proper
Proportional. Leave a thick coating and let it dry for at least 48 hours. Re-apply
For thicker coat. Available for coating floors, walls, desks, fixtures, wood work.
Special use for granite, marble and porous tiled surfaces of various colours and
Types. If there is excess localised deposition, then re-apply to remove and even
The surface. Apply uniformly to avoid accumulation.
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with skin. Can irritate
When exposed for a longer period. Harmful is swallowed. Do not inhale the
Vapours for long period. Highly flammable, do not bring near naked
Flame. Keep in cool place. Use in a well ventilated place/room.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 122 is an effective wide band micro-biocide designed
for use in algae and bacteria control. It does not cause
foaming and is not lost by evaporation from the system.
It is a concentrated blend of organo-sulfur compounds,
which should be added only after proper dilution by slug
feeding.
Application:
Use to control algae and bacteria in re-circulating commercial and industrial
water cooling towers. Prior to its use, systems be cleaned to remove algae
growth, microbiological slime and other deposits.
Dosage:
Initial slug additions of LC 122 per 1,000 gallons of water should be
employed every 1 - 5 days or as needed. The frequency of addition
depends upon the relative amount of bleed-off and the severity of the
microbiological problem. Slug additions should be made in the sump of the
cooling tower. During very hot weather, greater frequency or higher dosage
may be required to increase its effectiveness.
Handling & Precaution:
It is a very strong alkaline treatment and may cause eye damage and skin
irritation. Do not get in eyes, skin or on clothing. Wear goggles or face shield
and rubber gloves when handling. Avoid contamination of food. Harmful or
fatal if swallowed. In case of skin contact wash with plenty of soap and
water. Remove contaminated clothing and wash before reuse. If product
gets in the eyes, flush immediately with copious amount of clean cool water
for at least 15 minutes. If swallowed, call physician. Do not induce vomiting
or give anything by mouth to an unconscious person.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
2507 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
