1. Product Overview VHF finger expansion joints made by Vinh Hung Investment and Production Co., Ltd (VinhHung IP), include 2 types: Cantilever VHF-C and over-gap VHF-O, according to: AASHTO LRFD standards ASTM D 3542 92 (2003) standards VHFC and VHFO are synchronously manufactured with high accuracy finger plates and accessories like bolts, rubber sheets-water prevention steel plates that bring profitability to new construction as well as inspection and maintenance work in service. VHFC and VHFO accommodate the medium movement to big movement and can be used for both straight and skew bridges. 2. PRODUCT CHARACTERISTICS Totally accommodate the medium and large longitudinal movements, and also vertical and transverse movement if any... Simple installation, maintenance and replacement, which allows to replace the individual finger plates in short period of time and for each lane. High loading resistance capacity, especially the impact load. Also available for skew bridges. Rubber seal system is designed to be totally water-tight and prevent dust and debris. Can be designed to compatible with different thicknesses of bridge decks. To ensure the long-lasting durability, VHF finger expansion joints are protected from corrosion with methods like: paint with 2-component epoxy coating, PU-based painting (Polyurethane).., zinc coating according to ASTM A123, and especially Al-Mg coating (Al 5% and Mg 95% ratio) which ensures the durability of 100 years. This method is proved by the brine spraying test in 6000 hours (dry-wet 8hour cycles) according to ASTM B117 standards.
1. Product Overview VHM expansion  joint made by VinhHung Investment and Production Co., Ltd (VinhHung IP) are composed of multiple steel rails in combination with support beam and special structures. VHM - modular expansion joints accommodate to longitudinal movement from160mm upwards. The expansion joints are connected to the bridge deck through the anchoring reinforced system. Rubber seal serve as the drainage trough and prevent the system from dust and debris. 2.PRODUCT CHARACTERISTICS Design and manufacture according to AASHTO LRFD, TCVN 11823 2017 standards. Allow the longitudinal displacement of up to 720mm, the vertical and horizontal displacement satisfy AASHTO standards. Be able to withstand with high loads with stable and durable structure. Provide the smooth-riding surface while absorbing the impact of heavy traffic. Each center beam is fixed with an independent supporting bar, which satisfies the requirement of the fatigue threshold C (AASHTO 2007). Be protected with high anti-corrosive coating layer and treated with anti-skid coating technology. Be totally watertight.
1. Product Overview VSR Elastomeric Bearings made by Vinh Hung investment and production Co., Ltd (Vinh Hung IP) are in compliance with TCVN 10308: 2014, AASHTO LRFD Section 18, AASHTO M 251 96 (2011), BS5400, EN1337, KSF4420 VSR Elastomeric Bearings have been used in road bridge constructions, with a maximum load of 5000kN. 2 PRODUCT CHARACTERISTIC Elastomeric bearings are composed of rubber and steel plates which are chemically bonded through vulcanization. The thickness of the bearing is calculated to ensure the load, displacement and rotation as the requirement. Elastomeric bearings are simple geometric structures, bringing convenience during the installation, operation and maintenance. In addition, this type of bearing provides high resistance of vibrations impacted to the bridge span structures and piers.
1. Product Overview VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as: TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2. PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHB Pot Bearings made by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are in compliance with standards (TCVN 10268: 2014, AASHTO LRFD: 2007 Section 18, ASTM D 5212 03, BS5400, EN1337, KS4420). VHB Pot Bearings are capable of withstanding high loads, displacements and rotation angles. This type of bearing is suitable for middle-range span structure, continuous bridge structure, etc. with a load capacity of up to 60000kN or above depending on projectsâ?? requirements. VHB pot bearings have a well-shaped structure, superior design, which are convenient for installation and maintenance during operation. 2. PRODUCT CHARACTERISTICS VHB pot bearings are comprised of 4 main parts: top plate, piston, pot plate and elastomeric pad. The elastomeric pad is placed inside of pot plate, under the pressure of the load, the elastomeric pad experiences the temporary deformation inside the pot plate volume, it is capable of withstanding the forces and allows the movement as well as rotation along the horizontal axis. Piston and pot plate work as the connecting parts between the structures. Besides, the plus guiding part can be designed to limit or allow the movements as required from the structures. Pot Bearings are divided into 2 main types: Fixed pot bearings and sliding pot bearings. Fixed pot bearings: The bearings only allows the head of structure to have rotary movement and transfer the pressure through a fixed point. Sliding pot bearings: This type of bearings includes Free sliding bearings and Guide sliding bearings, which allows the dead to have both rotary movements and unidirectional or multidirectional movements. To ensure the long-life durability, VHB pot bearings are protected against corrosion by the following methods: painting with two-component epoxy coat, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg coating spraying method (at the ratio of 5% Al and 95% Mg) which ensures the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours.
1. Product Overview VSR Elastomeric Bearings made by Vinh Hung investment and production Co., Ltd (Vinh Hung IP) are in compliance with TCVN 10308: 2014, AASHTO LRFD Section 18, AASHTO M 251 96 (2011), BS5400, EN1337, KSF4420 VSR Elastomeric Bearings have been used in road bridge constructions, with a maximum load of 5000kN. 2. Product Characteristic Elastomeric bearings are composed of rubber and steel plates which are chemically bonded through vulcanization. The thickness of the bearing is calculated to ensure the load, displacement and rotation as the requirement. Elastomeric bearings are simple geometric structures, bringing convenience during the installation, operation and maintenance. In addition, this type of bearing provides high resistance of vibrations impacted to the bridge span structures and piers.
1. Product Overview VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as:TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2. Product Characteristics VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as: TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, â?¦ 2. PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
1. PRODUCT OVERVIEW VHM expansion joint made by VinhHung Investment and Production Co., Ltd (VinhHung IP) are composed of multiple steel rails in combination with support beam and special structures. VHM - modular expansion joints accommodate to longitudinal movement from160mm upwards. The expansion joints are connected to the bridge deck through the anchoring reinforced system. Rubber seal serve as the drainage trough and prevent the system from dust and debris. 2.PRODUCT CHARACTERISTICS Design and manufacture according to AASHTO â?? LRFD, TCVN 11823 â?? 2017 standards. Allow the longitudinal displacement of up to 720mm, the vertical and horizontal displacement satisfy AASHTO standards. Be able to withstand with high loads with stable and durable structure. Provide the smooth-riding surface while absorbing the impact of heavy traffic. Each center beam is fixed with an independent supporting bar, which satisfies the requirement of the fatigue threshold C (AASHTO 2007). Be protected with high anti-corrosive coating layer and treated with anti-skid coating technology. Be totally watertight.
1. PRODUCT OVERVIEW VHR joints made by VinhHung Investment and Production Co., Ltd (Vinh Hung IP) is the steel strip-seal joint comprising of two steel rails with anchor bars connected to embedded bars in the pier cap of the headwall of the abutment, elastomeric strip serves as the trough for drainage and debris, nosing materials: non-shrinkage mortar or concrete with minimum compressive strength of 40MPa. There are 2 main types of VHR expansion joints identified by the cross-section of the steel rails: VHR-C steel rail expansion joint and VHR-F steel rail expansion joint. 2.PRODUCT CHARACTERISTICS Totally accommodate to longitudinal movement up to 100mm, and also vertical and transverse movement if appear. Simple in design and installation, high load bearing and durability. The joints are designed suitably for curb and median structures. Totally water-tight. To ensure the long-lasting durability, VHF-steel strip expansion joints are protected from corrosion with methods like: coat with 2-component epoxy painting, PU-based paint (Polyurethane).., zinc-coating according to ASTM A123â?¦, and especially Al-Mg coating (Al 5% and Mg 95% ratio) which ensures the durability of 100 years. This method is proved by the brine spraying test in 6000 hours (dry-wet 8-hour cycles) according to ASTM B117 standards
1. PRODUCT OVERVIEW VHC spherical Bearings/ Bridge bearing manufactured by Vinh Hung Investment and Production Company Limited (Vinh Hung IP) are capable of withstanding the high loads and movements suitable for structures requiring the rotary angle equal or bigger than 0.015 rad in all directions. VHC spherical bearings are designed and manufactured according to current standards such as:� TCVN 11823, AASHTO LRFD, ASTM D5977, EN 1337, 2.PRODUCT CHARACTERISTICS VHC spherical bearings/ bridge bearing possesses a bottom plate (6) which has a PTFE sliding plate (4) on it is upper curved surface. A convex calotte (5) is placed on top of this, which, thanks to it is polished hard-chromium plated surface, can slide within the lower part with low friction, thus facilitating rotations about every axis. A second sliding plate of PTFE (4) is recessed into the upper surface of the calotte. Together with the upper plate (2) above it, this accommodates longitudinal and/or transverse sliding movements of the superstructure, if required. To reduce sliding resistance to a minimum, the lower surface of the top plate features a polished stainless steel sheet. In the case of bearings which should allow movement along one axis only, the direction of movement is controlled by guiding bars (3). In the case of fixed bearings, the top plate does not have a stainless steel sheet. The bearing is connected to the superstructure and the substructure by means of anchor dowels (1) or threaded sleeves (depending on design), or alternatively by means of separate anchor plates with shear studs. To ensure the long-life durability, VHC spherical bearings are protected against corrosion by the following methods: coating with two-component epoxy, PU-based painting (Polyurethane), hot-dip galvanization according to ASTM A123 standards and especially the Al-Mg spray coating method (at the ratio of 5% Al and 95% Mg) which ensure the anti-corrosion durability of up to 100 years, this method is proved by the salt-spraying test in 6000 hours (8-hour dry-wet cycle) according to ASTM B117
Hello, we specialize in manufacturing all kinds of finger joint board sizes of acacia, pine ... and follow requests.
Premium Quality Hay Baler Twine - Brand Name: Siam Ecofarm - a member of Siam Brothers Vietnam - Product Name: Hay Baler Twine - Composition: PP, PE, Master-batch, UV - Weight: 1 ~ 4Kg/coil Features: - Durable and high intensity - UV protected - It is soft to avoid hurting tree, UV resistance and reusable. - 1 year warranty
Multi Tomato Twine Tomato Twine in multiend type is special product of Siam Brothers which is used in greenhouses for hanging tomatoes, rock melon, cucumber and any climbers. With 50 end-tips used for convenience. Features: Super strong, low elongation High UV treatment Soft & Smooth Economical Available in green and white, but can make other colors.
Rope with lead is produced from PP, PE, masterbatch, UV. Product is used in aquatic product exploration and maritime transportation including: anchor, drag anchor, net making, main rope of net, mooring rope, etc. It has the shrimp or fish cage easily sink into the water without additional external lead attachment. It is also called bottom rope. Color: Light brown, light pinkâ?¦ or as ordered diversely by customers. Length: as ordered by customers. Characteristics : Durable and highly adhesive ,Anti corrosion, high tensile strength ( 50% higher than other types of rope), high ultraviolet ray resistance, high temperature bearing capacity, no decaying, no oil penetration or dissolving in any chemical.
Specifications:Using for Fishing, Using for Agriculture Material:Polypropylene, polyethylene or polyester Type:Braided Rope Brand Name:Cock Brand, Sea Horse Brand Model Number:60050 Number of Strands:3,4,8 Length:220m (or require) Diameter:1.5mm to 120 mm
PP rope: + 3 strands, 4 strands Material: PP, PE Diameter: 1.0 60 mm Length: 200m â?? 1000m or optional Color: mixed as required Usage: mooring rope, tail rope, main rope of net, trawl rope, sport, maritime transportation, industry and agriculture, etc. 8 strands: Material: PP, PE Diameter: 16 â?? 80 mm Length: 200m 1000m or optional Color: any color Usage: mooring rope, tail rope, main rope of net, trawl rope, sport, maritime transportation, industry and agriculture, etc.
Origin: Vietnam Type: bleached white rattan webbing, natural colored rattan webbing. Width: 45cm,50cm,60cm,70cm,90cm. Length: 15m Ingredient Statement: 100% rattan raw material. Preservation: No preservation are used. Payment terms: 100% L/C At sight. 40% T/T advance and 60% against copied B/L. Western Union. Delivery time: 10-15 days
Origin: Vietnam Type: bleached white rattan webbing, natural colored rattan webbing. Width: 45cm,50cm,60cm,70cm,90cm. Length: 15m Ingredient Statement: 100% rattan raw material. Preservation: No preservation are used. Payment terms: 100% L/C At sight. 40% T/T advance and 60% against copied B/L. Western Union. Delivery time: 10-15 days
Place of Origin: Vietnam. Brand Name: SDRope. Product: Polypropylene/Danline Rope. Structure: Twisted (3 strands or 4 strands). Sizes: 3mm 40mm (1/8 to 1-5/8) Length: 200m, 220m (standard) or customized (up to 1200m) Packing: bale covering by PP woven fabric or pallet (export standard). Features: Flexible, durable, high-strength, anti-abrasion, UV-resistant and outstanding quality. Materials: Virgin PP and PE. Colors: Yellow, white, blue, beige or customized.
