A.Product Overview: 1.The hose loop is used in oil field cementing, acid fracturing, etc; 2.The hose loop is assembled by swivel joint, hammer union and pup joint, can be swiveled in three directions flexibly; 3.The hose loop can be used in discharge pup joint, transportation pup joint, well testing pup join, well cementing pup joint, and transportation liquid flow under high pressure environment; 4.The hose loop can be matched with many kinds of swivel joints; 5.The hose loop has specifications of 2in, 3in, 4in and is adaptive to working under 42MPa(6000psi), 70MPa (10000psi), 105MPa(15000psi); 6.Hummer union can be connected or disconnected with pup joint. The disconnection is suitable for low pressure pup joint and connection is suitable for high pressure pup joint; 7.We are able to supply hose loop in each specification, pressure, length (according to expanded size) according to users needs. B.Design Features: 1.The swivel joint attached to hose loop is characterized by flexibility, impact resistance, vibration resistance, big rate of flow, etc. 2.The hose loop has fine sealing performance; 3.The hose loop is connected by union, which is simple to assemble and disassemble, crush resistance, and high sealing performance. It has the advantages of easy foldability, convenient transportation and storage; 4.We are supplying H2S proof hose loop under acid environment; 5.The thread joint conforms to international specifications and can be exchanged to like products internationally. Get more.
Surface safety valves (SSVs) are essential safety devices used in oil and gas production systems to prevent the uncontrolled release of hydrocarbons from the wellhead. They are designed to automatically shut off the flow of oil and gas in the event of an emergency, such as a blowout or equipment failure. SSVs are typically installed on the wellhead, and they are activated by a remote control system located at the surface. When the control system detects a potential safety hazard, it sends a signal to the SSV to close, which stops the flow of oil and gas from the well. This helps to prevent the release of hydrocarbons into the environment, which can have serious environmental and safety consequences. Design Details SSVs come in a variety of designs, but they all share the same basic components, including a valve body, actuator, and control system. The valve body is the main component of the SSV, and it contains a gate or ball valve that can be opened or closed to control the flow of oil and gas. The actuator is responsible for moving the valve, and it is typically powered by hydraulic, pneumatic, or electric systems. The control system monitors the wellhead for potential safety hazards and sends signals to the actuator to activate the SSV when necessary. The surface safety valve is an important component of wellhead production. When high pressure enters the drive, the bottom spring will open the valve. Through console operation, the spring on the relief valve will automatically push the stem to close the valve, thus ensuring the safety of the production. assembled safety valve with consideration of optimal safety and economics. The available safety valve sizes are from 1-13/16" through to 7-1/16", with pressure ratings from 2000psi to 20000psi.
The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. Product Description The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. The check valve design and manufacture of APImeivalve fully meet the requirements of API spec 6A and can be used interchangeably with equipment conforming to API spec 6A. The valve body is made of alloy steel forging, with strong mechanical properties, and can withstand high pressure, with safe and reliable performance. The bonnet and valve body are bolted together, and the seal is the sealing ring on the bonnet and the inner wall of the valve body. The sealing performance is reliable. It provides minimal assembly clearance between the bonnet and body (designed to be 0), thereby reducing erosion of bolts and holes by corrosive media and reducing bolt loads. Hard alloy is hard-faced on the core and sealing surface of the valve body so that it has good wear resistance and corrosion resistance. The core material should use sulfur-proof steel, and other parts should use the method of limiting hardness so that the valve can be used in an environment containing H2S. Install the valve body into the pipeline according to the flow direction on the valve body. The valve core by the upper and lower pressure to achieve movement and sealing so that the valve core can not be stuck. Technical Parameters 1. One-way flow of the working medium. 2. Working pressure: 2,000 psi ~ 20,000 psi 3. Nominal diameter: 2.1/16 "~ 4.1/16" (52mm ~ 103mm) 4. Working medium: oil, natural gas, mud, H2S and CO2 gas 5. Operating temperature: -46C ~ 121C (LU level) 6. Material level: AA, BB, CC, DD, EE, FF, HH 7. Specification level: PSL1 ~ 4 8. Performance level: PR1 ~ 2
The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. The check valve design and manufacture of APImeivalve fully meet the requirements of API spec 6A and can be used interchangeably with domestic and foreign equipment conforming to API spec 6A. The valve body is made of alloy steel forging, with strong mechanical properties, and can withstand high pressure, with safe and reliable performance. The bonnet and valve body are bolted together, and the seal is the sealing ring on the bonnet and the inner wall of the valve body. The sealing performance is reliable. It provides minimal assembly clearance between the bonnet and body (designed to be 0), thereby reducing erosion of bolts and holes by corrosive media and reducing bolt loads. Hard alloy is hard-faced on the core and sealing surface of the valve body so that it has good wear resistance and corrosion resistance. The core material should use sulfur-proof steel, and other parts should use the method of limiting hardness so that the valve can be used in an environment containing H2S. Install the valve body into the pipeline according to the flow direction on the valve body. The valve core by the upper and lower pressure to achieve movement and sealing so that the valve core can not be stuck. Technical Parameters 1. One-way flow of the working medium. 2. Working pressure: 2,000 psi 20,000 psi 3. Nominal diameter: 2.1/16 4.1/16 (52mm 103mm) 4. Working medium: oil, natural gas, mud, H2S and CO2 gas 5. Operating temperature: -46 C 121 C (LU level) 6. Material level: AA, BB, CC, DD, EE, FF, HH 7. Specification level: PSL1 4 8.Performance level: PR1 2
Meivalve company providing products including wellhead equipment and christmas tree, choke and kill manifold, mud manifold, casing head, tubing head, fracturing head, all kinds of high pressure valvesï¼?high pressure swivel joint, hammer union. Main products products are performing API 6A 16C standard, and can provide special product customization service according to customer's requir. Description The plug valve is an important part to connect the high-pressure manifold during cementing and fracturing operations and is also suitable for the control of other high-pressure fluids. The end of the plug valve is connected by the hammer union plug valve, LP internal thread connection and LP external thread connection. At the same time according to customer requirements to design a base high-pressure plug valve; Plug valve is mainly composed of the valve body, sealing arc slice, plug and other parts; Plug valve specifications are 1", 2", 3", cold working pressure 42Mpa (6000Psi), 70Mpa (10000Psi), 105Mpa(15000Psi) three grades, can be used at room temperature, low temperature and sulfur gas conditions and repair kit. The low-torque plug valves designed and manufactured by our company are all forged from high-quality high-strength alloy structural steel. The materials used are in full compliance with ASTM and AISI standards, and the product specifications are in full compliance with API Spec 6A. The plug valve manufactured by our company has a specification level of pls1-3 and a performance level of pr1-2, which can be interchanged with similar products of SPM and is widely used in cementing equipment and fracturing equipment.
Hydraulic Gate Valve Hydraulic gate valves are designed, manufactured, and tested in accordance with API Spec. 6A to ensure reliable and efficient operation in a variety of applications. The valves feature linear double-acting actuators that guarantee rapid opening in just 30 seconds, providing positive control during operations. Product Description Hydraulic gate valves are designed, manufactured, and tested in accordance with API Spec. 6A to ensure reliable and efficient operation in a variety of applications. The valves feature linear double-acting actuators that guarantee rapid opening in just 30 seconds, providing positive control during operations. API 6A Hydraulic Gate Valves are used primarily in the oil and gas industry for controlling the flow of fluids, such as crude oil and natural gas, in high-pressure and high-temperature environments. They are actuated using hydraulic systems, making them suitable for remote or automated operations. Features 1. The integral forging of the valve body, along with the use of carbide alloy on the sealing surface and seats, enhances wear resistance, and corrosion resistance, and extends the service life of the valve. 2. The metal-to-metal sealing between the gate and seat, seat and body, bonnet seal, and stem backseat provides a secure, long-lasting seal. 3. The balancing lower stem of the valve allows it to stay in position even in the absence of hydraulic power, and the double-acting actuator requires hydraulic power to both open and close. Should a failure of hydraulic power occur, this valve will remain in position. 4. Balancing stem that allows the gate to stay in position unless hydraulic power is supplied to the actuator to positively open or close valve 5. Two spring-loaded, pressure-energized, nonelastomeric lip seals provide low-pressure sealing and protect against particle intrusion, while the stem seal design is capable of handling a wide range of pressures, temperatures, and fluids. 6. Stem seal design that covers a wide range of pressures, temperatures, and fluids encountered in wellhead and manifolds service metal-to-metal bonnet seal. 7. A manual locking screw maintains the gate in the closed position without any operating pressure, and socket head cap screws are used to tie down the actuator head flanges, reducing exposure to corrosive environments.
Meivalve is a professional valve spare parts supplier and manufacturer that specializes in providing wholesale valve parts at competitive prices. Our extensive product catalog includes API 6A valve seat seals, peek seal rings, valve stem packing for FC gate valves, hammer union seals, valve stem U-packing seals, ring joint gaskets, and more. Our products are designed for the oil and gas industry, and we pride ourselves on delivering high-quality equipment and accessories to meet industry standards. With our commitment to quality and customer satisfaction, Meivalve is the go-to source for all your valve spare parts needs.
Ball screw gate valves are designed for large caliber, high-pressure manual valves. The valve combines the tail balance lever and the unique ball principle to make its operation light, low torque, and easy to operate. Its diameters range from 3 1/16 "to 9" and its pressures range from 10,000 psi to 20,000 psi. Product features: 1. Two-way downstream sealing structure, which improves the service life; 2. Fixed metal seal (between gate and seat and seat and body); 3. Simple and reliable gate and seat design can reduce field service; 4. Sealing ring between seat and body helps seal at low pressure. They also prevent granular contaminants from entering the body chamber and sealing area; 5. Stem seal design covers all pressure classes, temperature ranges, and all fluid conditions encountered in wellhead and manifold environments; 6. Metal seal between bonnet and valve body, up to 20000psi working pressure; 7. Reverse stem seal structure allows the valve to replace stem seal under pressure drive; 8. To ensure safety, a grease injection device can be placed on the stem after the inverted seal. The device can be placed on the bonnet to eliminate body leakage; 9.Ball screws can effectively improve the switching efficiency and reduce the switching torque, which is more conducive to opening and closing the valve easily and quickly. For more information, please visit our website.
Hydraulic gate valves are designed, manufactured, and tested in accordance with API Spec. 6A to ensure reliable and efficient operation in a variety of applications. The valves feature linear double-acting actuators that guarantee rapid opening in just 30 seconds, providing positive control during operations. Features 1. The integral forging of the valve body, along with the use of carbide alloy on the sealing surface and seats, enhances wear resistance, and corrosion resistance, and extends the service life of the valve. 2. The metal-to-metal sealing between the gate and seat, seat and body, bonnet seal, and stem backseat provides a secure, long-lasting seal. 3. The balancing lower stem of the valve allows it to stay in position even in the absence of hydraulic power, and the double-acting actuator requires hydraulic power to both open and close. Should a failure of hydraulic power occur, this valve will remain in position. 4. Balancing stem that allows the gate to stay in position unless hydraulic power is supplied to the actuator to positively open or close valve 5. Two spring-loaded, pressure-energized, nonelastomeric lip seals provide low-pressure sealing and protect against particle intrusion, while the stem seal design is capable of handling a wide range of pressures, temperatures, and fluids. 6. Stem seal design that covers a wide range of pressures, temperatures, and fluids encountered in wellhead and manifolds service metal-to-metal bonnet seal. 7. A manual locking screw maintains the gate in the closed position without any operating pressure, and socket head cap screws are used to tie down the actuator head flanges, reducing exposure to corrosive environments. Technical Parameters 1. Medium: oil and gas accompanied by sour gas or/and sand 2. Hydraulic actuator: 3,000 psi working pressure and 1/2 NPT connection 3. Rated Working Pressure: 5,000psi 20,000psi 4. Bore Size: all popular 5. Temperature: K ~ U 6. Material Classes: EE ~ HH 7. End connections: flange 8. Product Specification Level: PSL1 ~ PSL3 9. Performance Requirement: PR1, PR2
The choke manifold is a piping and valve arrangement with adjustable throttle valves. The assembly is primarily responsible for controlling flow and pressure in various industrial applications such as onshore and offshore oil well testing and production operations. Features 1. The choke manifold is the necessary device to implement well pressure control technology. It works on controlling the pressure, maintaining pressure balance inside the well and avoiding overflow and blowout; 2. To get too soft shut-in by choke valve pressure release, and to protect well mouth by open flow; 3. The choke line manufactured by our company conforms to the API 16C, NACE MR0175 Standards; 4. Special choke lines can be designed and made according to users' needs. 5. In case of malfunction of one chock valve, it is needed to close the upper and down valves and put the down valve of another chock valve into work; 6. When it needs open flow, it is necessary to open the flow valve and close the inlet valve of the drilling liquid-gas separator; 7. By means of the chocking effect of the check valve, the chock manifold can work on good control, replace the polluted drilling liquid, control the casing pressure and standpipe pressure of good mouth and recover the pressure on the well bottom caused by drilling liquid and curb overflow; 8. Pressure relief function of the check valve can be used to reduce the pressure of a good mouth and realize "soft shut in"; 10.Releasing liquid (gas) largely by a straight flow valve can reduce the casing pressure of a good mouth and protect the well mouth blowout preventer unit.
Api 6a valve ,casing head,casing spool.
Tubing Head Tubing head is a vital component in the oil and gas industry, enabling the safe and efficient production of hydrocarbons from underground reservoirs. It provides a secure connection for production tubing, controls wellbore pressure, and helps maintain the integrity of the wellhead system. Description The Tubing Head is an adapter between the first casing column and the blowout preventer set (during drilling) or wellhead (after completion). The adapter can be threaded or welded to the casing and can have flanged or clamped connections to match the blowout preventer set or wellhead. It is the primary interface for pressure control equipment. At the time of installation, the casing head is usually tested for very stringent pressure and leakage parameters prior to the installation of any surface equipment to ensure viability under blowout conditions. Characteristics The tubing head and tubing cross are used to suspend the tubing and seal the annular space of tubing. Its characteristics are: 1. The secondary sealing form between the tubing hanging and the reducer flange includes O-ring seal, greased BT seal and metal-to-metal seal; 2. The sealing forms of tubing hanging and tubing head are metal-metal seal, special synthetic rubber seal or metal seal + special synthetic rubber seal; 3. With grease injection port and sealed test port; 4. The lower sealing form of the tubing head includes O-ring seal, greased BT seal and metal seal; 5. The tubing hanging and tubing head reducer flange can directly pass through the cable and can be equipped with a downhole safety valve control pipeline interface; 6.The side exit link is threaded or wire-flange type, and is equipped with VR thread for easy valve replacement operation.
Description Hose loops are widely used in various oil well services, including circulating pipelines, water pipelines, emission pipelines, oil well test pipelines, and temporary stream pipelines. Our hose loops feature innovative and unique rotating joint technology, allowing for easy movement in any horizontal direction. These rotating joints also help control vibration and absorb impacts. Hose loops are especially prevalent in primary and secondary well-cementing operations. Design Features: 1. The hose loop is used in oil field cementing, acid fracturing, etc; 2. The hose loop is assembled by swivel joint, hammer union and pup joint, can be swiveled in three directions flexibly; 3. The hose loop can be used in discharge pup joint, transportation pup joint, well testing pup join, well cementing pup joint, and transportation liquid flow under high pressure environment; 4. The hose loop can be matched with many kinds of swivel joints; 5. The hose loop has specifications of 2in, 3in, 4in and is adaptive to working under 42MPa(6000psi), 70MPa (10000psi), 105MPa(15000psi); 6. Hummer union can be connected or disconnected with pup joint. The disconnection is suitable for low pressure pup joint and connection is suitable for high pressure pup joint; 7. We are able to supply hose loop in each specification, pressure, length (according to expanded size) according to users needs. 8. The swivel joint attached to hose loop is characterized by flexibility, impact resistance, vibration resistance, big rate of flow, etc. 9. The hose loop has fine sealing performance; 10. The hose loop is connected by union, which is simple to assemble and disassemble, crush resistance, and high sealing performance. It has the advantages of easy foldability, convenient transportation and storage; 11. We are supplying H2S proof hose loop under acid environment; 12.The thread joint conforms to international specifications and can be exchanged to like products internationally.
U-packing seals are a type of sealing solution that is commonly used in hydraulic and pneumatic systems to prevent leakage of fluids or gases. These seals are typically made from rubber or other elastomeric materials and are designed to fit into a groove or recess in the housing of the system is sealed. The u-packing seals consist of a packing made of rubber combined with a housing made of Teflon vulcanized. The rubber is the main pressure-bearing element, and the interference of the inner and outer diameters ensures that the housing is tight against the sealing contact surface, thus realizing the sealing principle. The U-shaped cross-section of the seal gives it its name, as it resembles the letter "U". The seal is typically installed with the open end of the U facing the pressure being sealed, which allows the pressure to force the lips of the U against the surface being sealed, creating a tight seal. U-packing seals are known for their ability to handle high pressures and provide reliable sealing performance over a wide range of temperatures and operating conditions. They are commonly used in medium-pressure valves with good leakproof performance. As a low-cost valve stem seal is widely used in the petrochemical industry.
Description Pup Joint, also referred to as Riser Spool, or Surface Riser Spool is a pressure-containing piece of equipment having end connections, used below or between drill-through equipment. The Spacer spool is a wellhead section that has no provision for suspension of tubular members and which may have no provision for sealing of tubular members. It is used to provide separation between two components with equal-sized end connections. providing exceptional performance as a wellhead extension, securing connection for choke manifold and kill manifold. Features A. Flanged, studded, and rubbed ends are available in any combination. B. We can produce a spacer spool for any combination of size and pressure ratings. C. Integral forged material ensures excellent reliable working performance. D. spacer spools are designed to minimize length while allowing sufficient clearance for wrenches or clamps unless otherwise specified by the customers. E. The standard Spacer Spools do not include outlets, although outlets can be added as per request. F. Our spacer spool is suitable for general working conditions and sour service. G. Stainless Steel 316L or Inconel 625 corrosion-resistant alloy ring grooves are also available. H.Normally we will provide tap-end studs and nuts with studded-end connections.
Description Peek (Polyether ether ketone) is a high-performance thermoplastic material that is known for its excellent mechanical, thermal, and chemical properties. Peek is often used in industrial applications where high temperature, chemical resistance, and mechanical strength are required. A peek seat is a component that is often used in valve applications. It is a seat made from peek material that is used to provide a tight seal between two components. A peek o-ring, on the other hand, is a type of o-ring made from peek material. O-rings are mechanical seals that are used to prevent the leakage of gases or liquids. Peek o-rings are known for their excellent chemical resistance, high-temperature resistance, and low friction coefficient. They are often used in applications where standard elastomeric o-rings would not be suitable due to their inferior properties. Sealing principle: The peek seat is a V-spring that is used as a force-applying element. The seal housing made of PTFE composite or peek has a good leak and crush resistance. As a seat seal ring, it is widely used in high-pressure valves, usually, the inner and outer seal rings of the seat are used together.
Wellhead Christmas Tree In oil and gas extraction, oil recovery trees or "trees" are a combination of valves, casing tetrads and fittings used to regulate pipe flow in oil wells, gas wells, water injection wells, water treatment wells, gas injection wells, condensate wells and other types of wells. Product Description Wellhead and Christmas tree equipment is an important equipment of oil and gas drilling, the casing head, tubing head, and oil (gas) tree of three parts, used to connect the casing string and tubing string, and the sealing between the layers of casing and tubing annulus, and can control the production wellhead pressure and adjust the oil (gas) wellhead flow, also can be used in acid fracturing, injection, testing and other special operations. Wellhead devices and trees can be divided into oil production wellhead devices, gas recovery wellhead devices, fracturing and acidification wellhead devices, thermal recovery wellhead devices, and other wellhead devices. The Wellhead devices and tree is mainly assembled by a gate valve, throttle valve, three-way, four-way, plug valve emergency cut-off valve and other pressure components. Working Pressur:2000PSi,3000PSi,5000PSi,10000PSi,15000PSi, Technical Parameters 1. Nominal diameter:2-1/16,2-9/16,3-1/16,4-1/16, 2.Specification level:PSL1,PSL2,PSL3,PSL3G,PSL4 3. Performance levels: PR1, PR2 4. Material level: AA, BB, CC, DD, EE, FF, HH 5. Temperature level: K, L, N, P, S, T, U, V 6. Working Medium: Oil, Natural Gas, Mud and Gas Containing H2S, CO2 7. Execution standard: API 6A, NACE MR0175 8. Main Components: Casing Head, Tubing Head, FC type Gate Valves, Flange, Cross, Choke Valve, Casing Hangers, Tubing Hangers, Pressure Gauges, etc. Wellhead Christmas Tree Features Well Intervention Pressure Relief Chemical injection Tree and well-monitoring points Flow composition and rates Valve and throttle position feedback Connection points
Meivalve is a professional pipe fittings supplier and manufacturer that specializes in providing high-quality products at wholesale prices. Our extensive product catalog includes a wide range of pipe fittings such as pup joints, union elbows, T-type tee joints, swivel joints, and hammer unions, among others. We take pride in our commitment to offering our customers competitive prices without sacrificing the quality of our products. Our team of experts is always ready to provide personalized quotes and assist with any questions or concerns you may have. Whether you are in need of standard pipe fittings or require customized solutions, Meivalve has the expertise and resources to meet your needs. Contact us today to learn more about our products and services.
Product Description 1. The Ring Joint Gasket Type: BX, RX, R(Oval & Octagonal), the Ring Joint Gasket is mainly used in high-pressure, and temperature applications in the petroleum industry. Mostly used for Valves, Pipes and Flanges. 2. Standard R types are in accordance with API 6A and ASME B 16.2 size. For both Oval and Octagonal configurations. They can interchange on the modern octagonal-type groove flange. 3. RX Type ring joint gaskets are manufactured to fit the API 6B flange"s groove, interchangeable with R(oval) and R(octagonal) series, bear pressure can reach 15000 PSI, so these gaskets performance excellent in 6B flange, suitable to the higher pressures with higher vibrations and heavier weights of these units. Spec.: RX20~RX215 4. BX-type ring joint gaskets are designed for BX flange grooves only, it is suitable for higher-pressure ratings starting at 2, 000 lbs and ending with 20, 000 lbs, incorporate a pressure balance hole to ensure equalization of pressure which may get trapped in the grooves. 5. The Ring Joint Gasket materials: Carbon Steel, Soft Iron, SS304, F5, 321, 304L, 316L, 316, 347. Or other materials according to your request.
Description Pup Joint, also referred to as Riser Spool, or Surface Riser Spool is a pressure-containing piece of equipment having end connections, used below or between drill-through equipment. The Spacer spool is a wellhead section that has no provision for suspension of tubular members and which may have no provision for sealing of tubular members. It is used to provide separation between two components with equal-sized end connections. providing exceptional performance as a wellhead extension, securing connection for choke manifold and kill manifold. Features A. Flanged, studded, and rubbed ends are available in any combination. B. We can produce a spacer spool for any combination of size and pressure ratings. C. Integral forged material ensures excellent reliable working performance. D. spacer spools are designed to minimize length while allowing sufficient clearance for wrenches or clamps unless otherwise specified by the customers. E. The standard Spacer Spools do not include outlets, although outlets can be added as per request. F. Our spacer spool is suitable for general working conditions and sour service. G. Stainless Steel 316L or Inconel 625 corrosion-resistant alloy ring grooves are also available. H. Normally we will provide tap-end studs and nuts with studded-end connections. Technical Parameters Product Name: Spacer Spool, Riser Spool, Pup Spool, Pup Joint Pipe, Pup Joint Bore Size: 1-13/16", 2-1/16", 4-1/16", 5-1/8", 7-1/16", 13-5/8", 20-3/4", 21-1/4" or customized Overall Length(OAL)/Height: As per customers' requirements Connection: API 6A Flange, API 16A Clamp, WECO Union Standards: API Spec 6A, NACE MR0175, Working Pressure: 3000 PSI to 20000 PSI Material Class: AA, BB, CC DD, EE, FF Material: Made from high-strength alloy AISI 4130 (Integral Forged) 60K, 75K, and processed especially with heating treatment, suitable for H2S environment. Temperature level: Working Medium: Oil, Natural Gas, Mud Performance Requirement: PR1, PR2 Product Specification Level: PSL1, PSL2, PSL3, PSL4 Paint Color: Red, Blue, or Customized
