In-circuit Test Probe Pogo Pin P085 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P085 series here. Its diameter is 0.82 mm and the total length is 37 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Rated Stroke: 2 mm Spring Force: 130 gf (5oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CH200-H(14) for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CH200 harness probe we will introduce here is 1.99 mm in diameter and 39 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.5 mm at most when this probe works, although the plunger can move as far as 7.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.5 mm, its loaded force is about 312 gf, namely 11 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 7.3 mm Rated Stroke: 4.5 mm Spring Force: 312�?�±65 gf (11 oz) at load 4.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Assembly Test Probe Pogo Pin PQL50 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQL50 series here. Its diameter is 0.78 mm and the total length is 43.2 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles to fit the probes, for instance, CR, SW, CRW and WW. The plunger can be pressed at a distance of up to 6.35 mm. But it is better to be pressed at a distance of 4.3 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 4.3 mm, the loaded force is about 5.5 oz, 7 oz or 8 oz, which fluctuates to a tolerance. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 60 milliohms Mounting Hole Size: Diameter 1 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/ 185 gf (7 oz)/ (227 gf (8 oz) Materials Receptacle: Phosphor Bronze, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP114 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP114 series of battery contact probes. The outside diameter is usually 1.14 mm and there are some common tip styles, for example round head or pointed head. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 1.14 mm Rated Stroke: 1.14 mm Spring Force: 110 gf (4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Spring-loaded Pogo Pin CHZ136-J Series Applied to Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHZ136-J harness probe we will introduce here is 1.36 mm in diameter and 32.8 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.6 mm at most when this probe works, although the plunger can move as far as 6.9 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.6 mm, its loaded force is about 130 gf, namely 4.5 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.9 mm Rated Stroke: 4.6 mm Spring Force: 130�?�±40 gf (4.5 oz) at load 4.6 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Semiconductor Test Probe SCPA025 Series for IC Test Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA025 we will introduce is 0.25 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 14 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel�¯�¼? Ph/SP, Au on Ni Plated Bottom Plunger�¯�¼? BeCu, Au on Ni Plated Top Plunger BeCu, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 1 amp Contact Resistance 100 milliohms max Bandwidth ? 9.3 GHz at -1dB Inductance 1MHZ at -0.02384 uH Captance 1MHZ at 1.06747 uF Specifications: Full Stroke 1.1 mm Rated Stroke 0.65 mm Spring Force 4 gf at load 0.65 mm Mechanical Life about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Hitachi 2012 SCENARIA 64 -128 Slice * New tube installed: May 2021 * Tube type MCS-7070HP * Tube 7.5 MHU * Tube scan seconds: 219,918 sec
Electronic Test Probe Double-ended Pogo Pin SCPC030(50)-XX-67 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC030(50)-XX-67 we will introduce is 0.3 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The top plunger is made from SK4 plated with nickel and gold. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.8 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.8 mm, the loaded force is about 12 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 100 milliohms max Bandwidth: 7.5 GHz at -1dB Inductance: 1MHZ at -0.05032 uH Captance: 1MHZ at 0.502464 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.8 mm Spring Force: 12�?�±3 gf at load 0.8 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Test Probe Pogo Pin SCPA020 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins.  Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA020 we will introduce is 0.2 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. � Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottome plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from SUS304 plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 200 milliohms The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise the spring will probably be damaged severely under constanct pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 12 gf, which fluctuates to a tolerane. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP  Au on Ni Plated Electronic Specification: Current Rating: 1 amp Contact Resistance: 200 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.13527uH Captance: 1MHZ at 0.186437uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.6 mm Spring Force: 12 ±4 gf at load 0.6 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. Welcome to browse our website centalic.com and download any catalogs of our products.
Electronic Test Probe Double-sided Spring Pogo Pin SCPA057 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA057 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3 Amps Contact Resistance: 100 milliohms, max Bandwidth: 5 GHz at -1dB Propagation Delay: 24 ps Inductance: 1MHZ at -0.03664 uH Captance: 1MHZ at -0.704638 uF Specifications: Full Stroke: 0.63 mm Rated Stroke: 0.5 mm Spring Force: 45 ±13 gf at load 0.5 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Portable Ultrasound Machine Manufacturer year : 2017 Used condition like new, Excellent and ready to work Come with warranty 12 month Features: The provides advanced imaging quality and a high level of functionality that provides efficiency to support the most accurate diagnostic activities. The system s monitor includes a full touch panel for intuitive operation right at your fingertips, while the basic operations, such as image size or gain adjustment, can be made with one hand using touch screen gestures. Include: Main unit Linear probe L64 (frequency 5MHz-18MHz) Black and white printer Manual book Power cable Specification: Monitor: 11.6 inch full touch panel (FullHD) Size: 29.6 cm (W) x 26.0 cm (D) x 7.5-26 cm (H) Weight: Approximately 4.5 kg Image signal external output: HDMI Frequency probe: Maximum 18 MHz
GE Voluson E10 Ultrasound BT18 With 3 New Probes - Refurbished GE Voluson E10 Ultrasound BT18 with all scanning options active, 3 new Ultrasound transducers : 4D convex, 2D convex and 2D endovaginal. Unit is in like new working condition, used for demonstration only, no clinical use and comes with 1 year warranty
GE V-SCAN DUAL PROBE PORTABLE ULTRASOUND MACHINE. BRAND NEW IN SEALED BOXES
Application OB/GYN Abdomen scan Superficial parts Urology Ophthalmic scan MSK Nerve block Feature Integrated clipboard, display the saved image at the bottom of the screen, which can be directly called or deleted Preset optimized image inspection conditions for different inspection organs, reducing adjustment procedures during operation Abdomen, uterine attachment, heart, fetus, urinary system, prostate, blood vessels, small organs, newborn, musculoskeletal, intraoperative scan Complete Probe Family,� probe box silicone lining, effective protection of probe Subarray Technology Harmonic Imaging Technology (THI) CE certified
Carestream CS 3600 Intraoral Scanner Wand 3D Imaging Intuitive Features for Improved Clinical Outcomes: Get started quickly with continuous feedback that helps you perfect your scanning skills. Reach expert scanning level quickly with live scanning warnings that provide feedback in real time, indicating areas of the scan that lack detail and require additional scanning to optimize your clinical outcome. â?? Green arrows guide the way: Green arrows display the ideal direction in which the user should rescan missing information, providing real-time feedback that significantly increases scanning efficiency. â?? Get alerted of missing data: Yellow and green highlights alert you of any gaps or holes in the scan, indicating that the area needs to be rescanned for optimal detail. â?? Confirm your preparation: Undercut check automatically detects undercuts based on the selected area, helping to ensure your digital impression is optimal for the restoration. â?? Aesthetic scans that reflect reality: Self-adaptive filling automatically identifies holes and selects the appropriate anatomical color for the optimal aesthetic outcome. Stunning HD 3D Digital Impressions: Full HD 3D color images offer enhanced image quality with more vivid color and texture. One Scanner, Three Workflows: Dedicated workflows for restoration, orthodontic and implant-borne restoration cases keep you on task. Now Available in Monochromatic Only Scanning: Enter the digital realm on your terms The new Carestream CS3600 Intra Oral Scanner Access intraoral scanner delivers the same quality, accuracy and efficiency as the CS 3600 but with monochromatic scanning, providing you with an affordable entry into digital impression scanning. The CS 3600 Access can be easily upgraded to HD 3D color at any time for full spectrum digital scanning. High-Speed Continuous Scanning: The Carestream CS 3600 Intraoral Scanner Wand 3D Imaging unique continuous scanning capabilities makes it faster than ever to acquire a scan. Continuous scanning allows the user to scan in a smooth, uninterrupted manner, greatly reducing the time it takes to capture a digital impression. This high speed makes it ideal for time-consuming dual arch scans. Plus, since sudden movementsâ??such as the userâ??s hand shaking or the patient shiftingâ??have little to no effect on successive views, scans can be completed seamlessly despite interruptions to workflow. Intelligent Matching System: Freely complete any missing data in any area.
Sale GE Versana Active Ultrasound Machine Manufacturer year : 2020 Used condition like new, Excellent and ready to work Come with warranty 12 month Features: The Versana Active v1.5 Primary Care Ultrasound System provides accurate and high-precision ultrasound imaging data of a patient. Versana Active is an AI-enabled primary care ultrasound system with precise tools designed to enable rapid patient assessments and confident decisions. This systemâ??s robust design makes it suitable for patient monitoring in the hospital and an office setting. Adaptable and Easy-to-use: This primary care ultrasound system offers excellent ease to health care providers with its utilitarian design and configurability. An expansive 15.6 LCD screen has an intuitive interface and gives a clear and bright display of the ultrasound image and other vital data. A keyboard with a set of pre-programmed quick-access buttons provides easier and greater control to the user. Changing settings and choosing what you want to see only requires a few strokes of your fingers. In addition to an excellent display and controls, this system has several attachment points for a gel cup and probe holders. Handles on the front and back and a set of large-high-quality wheels make it highly maneuverable. All the cables and leads are appropriately managed to avoid clutter and entanglement. The cart s height can also be adjusted to suit the scan requirements. Facilitates Simple Workflow: Proprietary algorithms synthesize patient data and enable fast assessments and confident decisions. A shared underlying platform provides a common user experience and simplifies training protocols. The software includes several display modes and diagrams to facilitate easy and quick assessment. Versana Active can assist with a number of medical procedures and conditions, including sonobiometry, thyroid assessment, tissue doppler imaging, B-flow representation, tissue velocity imaging, etc. For greater assistance of the medical staff, there are many viewing options of the acquired images to make the analysis easier. All the data can be easily stored and tracked to help medical personnel follow the patients response to therapy. Precision Assessment Applications: The wide variety of high-quality precision probes that adapt to this system are useful for several applications. These probes provide a crisp and clear image of the target area, facilitating critical procedures like perioperative care, tendon, muscle and joint assessment, pediatric assessment, and neonatal care. Package Include: - Versana Active Ultrasound System - Probe L6-12-RS - Cart - AC Adapter
Certificate: CE, FDA, CMDCAS Screen: LCD or TFT Working frequency: 2.5 MHz or 3.0 MHz Measuring mode: Manual Calculating mode, Average mode, Transient mode
Apache ultrasound system is a handheld ultrasound built-in 64 physical channels and patented micro-beamforming technology to provide high-quality medical imaging. Extremely low power consumption enables a long scanning time. Easy to carry and connected with mobile devices, medical imaging becomes reachable at your fingertip.
Application: Abdomen, obstetrics, gynecology, heart, urinary system, small organs, superficial, blood vessels, pediatrics, newborns, musculoskeletal
It is a Micro & Macro HIFU Ultrasound Focus Ultrasound technology System , Professional for face lifting , skin tightening , and body contouring . ;) There are 7 catridges with difference depth . ( 4 cartridges for face and other 3 cartridges for body ) 1.5mm:targeting at the epidermis to improve superficial fine lines,skintone,skintexture,and fine pores. 3.0mm,aiming on the dermis to stimulate continuour regen eration of collagen. 4.5mm,cting on sama fascia layer to tighten the muscle bottom and achieve firmness 6.0mm,9.0mm,13.0mm,different layers of sectokill cellulite dissolve fat to gighten and shape, releasing curvaceous beauty The 2.0mm cartridges is the original one in the world , and can be operated in all parts without restricted area . It can do more precise and more targeted treatment . .Compare with the traditional HIFU , it reduce the Focus point diameter is 0.25mm , It means same energy with more smallers treatment point . It also why the 7D hifu machine feeling is more comfortable and result is more better .