Cosmetics & skincare, frozen delicious cake, pipes, pumps and water pumps, repellent .
COLOUR COATED PRODUCTS Colour coating of coils means continuous applying of paint to flat steel strip (rolled in a coil shape) with polyurethane rolls using high-tech automation. Colour coated strip is continuously produced on the line as described in the below steps. Coils are opened, top and back surfaces of the strip are cleaned (by applying a special chemical agent and rinsing it off), chromated (an operation to increase the corrosion resistance and to enhance the paint adherence). After that the strip passes through the oven, and the primer is applied to it (paint is applied only to top surface, while back surface is covered with high adhesive polyurethane back coating paint). Thereafter, the strip passes through another oven. If colour coating is requested over the primer on both sides, the paint is applied as the last layer and the strip is dried in the furnace. Depending on the customers request, protecting film may be applied, and the colour coated strip is rolled in a coil and packed.
NATURAL ALUMINYUM PLAIN COILS AND STRIPS DIMENSIONS Alloy : 1XXX, 3003, 3005, 3103, 3105, 5005, 8XXX Temper : H0, H1X, H2X, H3X, DDQ Thicknes : 0,20mm - 3,00mm Width : 500mm - 2200mm PAINTED ALUMINYUM DIMENSIONS Paint Type : Polyester, PVDF Colours : Ral Colours Alloy : 1XXX, 3003, 3005, 3103, 3105 Temper : H1X, H2X, H3X Thicknes : 0,30mm - 1,00mm Width : 300mm - 1500mm
Having passed Hot Strip Mill and Continuous Pickling Line, after rolling on Cold Reversing Mill (CRM), full hard products with surface quality and thickness (0.25-2.00 mm) suitable for further processing on HDGL are produced. Zinc coating is applied by continuous annealing followed by immerging of the strip into zinc pot on Hot Dip Galvanizing Line (HDGL) To protect the surface of galvanized products from corrosion, chemical passivation and protective oil may be applied. Products with thickness ranging between 0.25-3.00 mm and width ranging between 800-1530 mm may be produced on Hot Dip Galvanizing Line.
Galvanised steel, cold rolled steel, hot rolled steel.
Hot rolled coils, cold rolled coils, galvanized coils/sheets, aluzink coils, prepainted steel coils, wire rod, re-bar, billets, slabs.
Steel like GI GL, PPGI PPGL, CR, HR, HRP, ALU..Export
Fin Tube Heat Exchangers, Air Cooled Condensers, Cold Room Evaporators, Dry Coolers, Heater Cooler Coils, .
Steel Coil, Steel Coil Sheet, Steel Coil Plate, Hollow Sections, Tubes And Pipes (hr, Cr, Galvanized, Galvalume)..
Steel profiles & carbon steel welded tubes.Manufacturing & exporting worldwide
Prepainted Steel, Prepainted Aluminum, Aluminum Coil, Galvanized Steel, Cold Rolled Steel, Sliting Steel, PPGI, HDGI, CCR, Corugated Steel, Trapezoidal Steel, Sandwich Panels, Roof Panels, Wall Panels, Cold Room Panels.Steel Service Center, Solition Partner And Supply Center.
Steel section, wire, pipe, coils and plates.
Steel coils, color coated steel, trapeze sheet.Shipping, logistics
Stainless Steel, Galvanized Sheet Metal, Steel Wire, Straight Razor Wire .
Industrial Pipes, Rectangular Hollow Sections, Square Hollow Sections, Pre Galvanized Steel, Tubes & Hollow Section, Hrc Hot Rolled Steel Coils, Crc Cold Rolled, Steel Coils,hot Rolled Steel Sheets, Galvanized Steel Coils And Sheets, Cold Rolled Steel Sheets, Oval Profiles, Tz Profiles, Open Profiles, Slitting Line,.
Soybean GMO #2 Specialty: GMO Genetically Modified Organism Grade # 2 Suitable For Human Consumption Quality: Standard Export Quality Grade: 2 Gmo Test Weight: 54 Pounds Per Bushel,Min Protein: Min : 35% - 38% Moisture Content: Max 13,5% Foreign Material: Max 2,00
Sandwich panels are composite materials produced of two dyed Galvanized or Aluminum corrugated plates filled (with PIR, PUR, Rock wool) for thermal insulation. Used as coating materials in the roof, wall and internal partition or cold rooms of the buildings, sandwich panels provide a quite high level of thermal, water, sound insulation; prevent moisture condensation. In addition, they are distinguished with their bearing capacity as well. Bearing capacity of the sandwich panel depends on the density, thickness of its filling material and the form of its metal surfaces. Sandwich panel is an economical solution when assessed within the context of cost-benefit analysis. Thickness of the metals (DGS, Aluminum) and filling materials is determined in accordance with the area of usage and the amount of load they will bear. The climate conditions of the region of usage should be taken into account while determining the thickness of the filling material. Sandwich panels set the outer shell of the buildings in an aesthetic and affordable way by providing thermal, water and sound insulation without the need for any coating such as plaster or dye. They are procured with the best prices and used in the buildings whose load-bearing system is of steel and prefabricated concrete, such as industrial buildings, military buildings, social buildings, agricultural buildings, sports facilities, construction sites, silos, hypermarkets, shopping malls, cold storage depots and marketplaces. The products to meet the requirements of any kind of architectural project are produced with aluminum or dyed galvanized sheet metals, in requested amounts and dimensions at Starmet.
With Starmet corrugated sheets, thanks to their property of giving radius (curve) shape, it is possible to apply coating with application in place of a thermal insulation layer between two layers of corrugated sheets at the vaulted roofs with aesthetic appearance. Another area where the single layer corrugated sheets are used are the terrace roofs. In such applications, there is water insulation with membrane at the upper part of the roof. Starmet Yapı , in order to meet such needs of the sector in conformity with the values of the project provided by the customers, performs production according to the vaulted roofs, in the computer-controlled bending machine with an affordable price and high quality. Form 27/200 corrugated sheet, form 38/151 corrugated sheet, form 18/838 corrugated sheet, form 52/1000 DECK corrugated sheet, fand form 75/215 corrugated sheet are produced. It gives the advantage of easy and fast assembly on roof and wall, saving on the bearing construction thanks to its lightness, does not take a big place in construction sites and warehouses, is environment friendly due to its recycling feature. Areas of application; It offers safe and affordable solutions of high quality in the buildings whose load-bearing system is of steel and prefabricated concrete, such as industrial buildings, military buildings, social buildings, agricultural buildings, sports facilities, construction sites, silos, hypermarkets, shopping malls and marketplace buildings.
Hrp, cr and galvanized steel as coil, strip and sheet, roofing sheets.
Hot rolled sheets, cold rolled sheets, slit sheets, plate sheets.
