We sell all over the world
Types of Iron
Carbon steel iron
Welded wire rebar
European rebar
Sheet metal iron
Stainless steel iron
Galvanized iron
Expanded metal mesh iron
The diameters of the iron types are 8 mm, 10 mm, 12 mm, 14 mm, 16 mm, 18 mm, 20 mm, 22 mm, 25 mm and 32 mm.
Foundry Pig Iron is suitable for iron castings used in general engineering, machine
tools and parts for the automotive industry. Due to the high proportion of iron ore
used in the production of Foundry Pig Iron, the formation of pearlite in the finished
casting is promoted. This effect is enhanced when more than 10% of Pig Iron per
charge is used.
The use of Foundry Pig Iron promotes graphite formation, reduces primary chill and
improves machinability, particularly important in thin-walled castings The use of costly chill reducing inoculants can be minimised through increased addi-
tions of Foundry Pig Iron.
The high density and high carbon content of Foundry Pig Iron improves melting rates
or reduces energy consumption. In an electric induction furnace savings can be as
high as 50 kWh/t of molten metal. In a cupola furnace savings of up to 50 kg coke/t
of molten metal can be achieved.
The higher bulk density of pig iron relative to scrap means lower storage space re-
quirements, less handling during charge make-up, fewer charge buckets and lower
charging time.
â?¢ The lower surface area : volume ratio relative to scrap means lower oxide (rust) for-
mation and thus lower slag volume.
The carbon content is chemically combined and thus goes into solution more quickly
with lower energy requirement than when adding a recarburiser to scrap
Casting iron products, foundry, manhole, gratings, ductile cast iron tree gratings, cast iron castings, contract manufacturing of cast iron casting, outsource for cast iron casting, subcontractor for cast iron casting, drain covers, Casting Channel, polymer Channel, polymer concrete drainage channel c/w ductile iron grating, Ductile Iron U Channel Grid for Rainwater System, Ductile Iron Gully Grating, Ductile Iron Channel Grating Water Grates, Cast Iron Sewer Grating for Sewerage System, Ductile Iron Drain Grid, Ductile iron gratings, Ductile Iron Grate and Frame, Cast Iron Drainage Grid EN124, Rain grate, Ductile Iron Locking Grid, sewer cover, DCI Manhole Cover, Ductile Iron Manhole Cover,Square Manhole Cover,Cast Iron Manhole Cover En124 F900 E600 D400 C250 B125 A15, Access Covers, Gully Grates, Kerb Drainage, Surface Boxes, molding, hs code 732599, Polymer Concrete Channel, Precast Channel, drainage channel, channel u, concrete water channel, polymer concrete linear Drainage channel, EN1433 Polymer Concrete Channel Drainage System, EN 1433 Drainage channels for vehicular and pedestrian areas - Classification, design and testing requirements, marking and evaluation of conformity
Cold Briquetted Iron (CBI) is defined as DRI which has been molded at a temperature less than 650 �°C or with a density of less than 5000 kg/m3. Due to the raw material sharp shortage for steelmaking in many countries worldwide, a need arises to find a substitute material to replace the rare pig iron and expensive steel scraps that were used by steelmaking plants.
1- More density and less porosity
The apparent density of CBI is about 8.3 grams per cubic centimeter and the density of DRI is about 2.3 grams per cubic centimeter. On the other hand, the volumetric porosity of these two products is about 30 and 50%, respectively. These two factors reduce the environmental reactivity of CBIC and its lower transportation costs.
2- Less fine
The wear resistance and higher mechanical strength of CBI compared to sponge iron causes less softening to occur during the handling of the product, and as a result, both the economic value of the product is prevented and the charge losses of the product in the steelmaking furnace are prevented. is significantly reduced.
3- Easier to store and carry
Due to the lower reactivity of CBI compared to DRI, the loss of metal grade of the product during storage and transportation is significantly reduced, which will reduce the amount of economic value loss of the product from the time of production to the time of use in the steelmaking furnace. On the other hand, sea transportation of CBI leads to a reduction in transportation costs compared to DRI due to the absence of the need to apply neutral gas to prevent product activation.
4- More thermal and electrical conductivity
The thermal and electrical conductivity of CBI is about 2 times that of DRI. This higher conductivity of CBI improves the distribution of heat created in the steelmaking furnace and, as a result, accelerates the melting process of iron materials. This will mean reducing the melting time of the steelmaking process and improving the production capacity of the steelmaking unit.
5- Carbon adjustment
The presence of carbon in steelmaking furnaces is necessary in order to provide carbon for the final steel product, prevent excessive losses of iron, and also regulate the physical and chemical conditions of the slag. Usually, induction furnaces require low-carbon iron materials, but in electric arc furnaces, high-carbon iron materials are more attractive. The unique feature of CBI product is the ability to adjust its carbon content in the range of 0.5 to 4% by weight and based on the needs of customers.
Iron wire, bright wire, black wire, hot dip galvanized wire, electro galvanized wire, annealed wire, fencing wire, greasy bale wire for paper and ped recyclers, binding wire for constructions, metric barbed wire, copper coated wire, cut wire for panel fancers.
Manual height adjustment 40 to 90 cm
Completely electrostatic stainless paint
Monoblock steel top ironing surface
Colored bright cotton cover
Special design to facilitate ironing
Special iron rest with incombustible silicon fitting
Electric socket 16a
Colour options:white, grey, chrome
Monoblock ironing surface
Product dimension:34x112x90 cm
Package dimension:33.7x143.4x5.5cm
Weight:5.2kg
