Our pipe production lines are designed by considering the maximum product capacity and minimum energy consumption within the desired pressure class or wall thickness. Thanks to PLC and screen located on the line, the operating parameters of the line can be reported such as line speed, line working time, production quantity, machine working recipes. Extruder machine is used for melting and stirring plastic raw material. Masfen produces sprecific screw and barrel for material type that provide perfect mixing and homogeneity. Our Extruders have 50kg/h to 1000kg/h capacity for PE, PEX, PP, PPRC, PVC type of plastics.
IBT 42-33 3 speed motor (65 130 195rpm) IBT 42-VE Electronic speed variation (20 195 rpm) Width (A) : 620 mm Height (B) : 1280 mm Depth (C) : 900 mm Shipping Weight : 250 Kg Cold Water Paste : 10 Kg with Spiral Hook Egg Whites : 80 pcs with Whisk Supply Voltage : IBT 42-33 380-415 V/3P/50-60hZ IBT 42-VE 200-220 V/1P/50-60hZ Electrical Power Max. : IBT 42-33 1,0-1,5-1,85 kW IBT 42-VE 3,0 kW Performance (Up to) : 10 Kg / Cycle Capacity : 40 litre Construction 1 Corrosion resistant electrostatic paint on the body of the machine. Also available in AISI 304 Stainless steel. 2 AISI 304 Stainless steel bowl with a 40 liter & 10kg capacity with a 3 speed motor and an electronic speed variator. 3 Asynchronous motor with high start-up torque % waterproof button with a timer up to 60 minutes. 4 Water protected planetary system (IP54 electrical controls, IP 32 overall machine) with a lever for easy mobility of the bowl. 5 Power : 1,0-1,5-1,85 kW for IBT 42-33 3,0 kW for IBT 42-VE 6 Planetary movement based on belt driven oil-less planetary system.
(Fine product) Final product drying machine is the machine where the moisture of the bulgur where it transferred from the mill or polishing machine is reduced to the desired value. It is manufactured in different designs and dimensions according to the architectural and capacity of the plant. Fine product drying tower works with the logic of absorbing the evaporated water from inside of the product while it is moving from up to bottom via the hot air which its route was also adjusted as gradual from up to bottom as the forced line. The product which will be adjusted to desired moisture content is proportionally poured into the lower bunker with the help of the variator. It uses steam or thermo-block which is a hot air generator as the heat source. The fine product drying tower which was produced by TOPRAKÃ??ILAR has a tubular system which is designed to keep the product moisture at the same rate for each grain and it has also semi-dissembled design. In this way, the dead spots in the post drying are minimized and mold and fungus growing are prevented. For more
We produce full automatic, hygenic, non touching disposable mask making machine. From fabric to complete mask not contacting by human hand. Disposable Surgical Face mask making machine clothinhmachinery.com
Laser Cut Detailed Metal Scaled Berger
H 100 NAIL MAKING MACHINE Cutting Nail Diameter : Ã? 2.40 4.40 mm. Cutting Nail Length : L 50 100 mm. Cutting Per Minute : 350 pcs. Capacity : 550 1200 kgs/8 hours. Engine Power : 7.5 KW.
H 150 NAIL MAKING MACHINE Cutting Nail Diameter : Ã? 3.40 4.90 mm. Cutting Nail Length : L 80 150 mm. Cutting Per Minute : 260 pcs. Capacity : 700 2500 kgs/8 hours. Engine Power : 7.5 kW.
HELLO, MY NAME IS MUSTAFA, WE ARE THE MANUFACTURER OF MACHINERY FOR SEED SCREENING AND BULK HANDLING MACHINES. SEED, PULSES, LENTILS, NUTS PROCESSING LIKE STONE SEPARATORS, TREATERS AND BAGGING SCALES. ALSO ALL TYPE OF BUCKET ELEVATORS, BELT CONVEYORS AND AUGERS. WE WILL BE HAPPY TO BE YOUR SOLUTION PARTNER.
Super Yunus Series has 163 cm inner pick-up width, in this way Super Yunus has the feature of further increasing the yield. Super Yunus designed to work in dry and wet material with chopper and without chopper option. Strong and durable framework that you can use it for a long time. Super Yunus Baler Machines can be produced according to our customer's demands with 2 knotters 3 knotters or wire knotters.
Vibro Separator
Separator Air Duct
The Separator Semolina
2 units of tunnel kiln and transfer line
Machine type - k-550k-100 Production 5 layered10 layered Inside diameter 25 100 mm20-100 mm Cutting length1000 3000 mm1000 4000 mm Total motor power6 kw6 kw Numbeer of blades1 unit1 unit Air pressure 6 ba6 bar Width thickness 1, 5-6 mm1, 5 -5 mm Production speed25 meter/minute25 meter/minute Speed controlelectronicelectronic
Mechanical Model Panther 100 Machine Round Baler & wrapper Machine Weight 5500 kg Length 8600 mm Width 2200 mm Height 2600 mm Wheels Dimension 400/60-15.5 Number of Wheels 2 Number Axel Single Axel Vehicle connection Single point from front Bale Dimension 550*630 mm Bale weight 70-120 kg Capacity 60 Bales/h Chamber working system Gear to Gear with chain Compaction system Roller with rubbber belt Hydraulic Unit Two different hydraulic unit with cooling fan Net or Film binding system Pneumatic 700 mm wide Wrapping System Double wrapping arm with 375 mm Film roll Electrical Required Power 10kw Required Volt 380 volt (3 phase) Operating System Electronic Control System PTO Optional
Paper Cutting Width: 1500-3000 mm Minimum Paper Cutting Width: 40 mm Number of Paper Cutting Blades: 15 pieces Maximum Cutting Speed: 400 m/min
Number of Layers: 5 to 30 Layer Cutting System: Multi Knife or Opposing Knife (with Sew Eurodrive servo motor) Minimum Cutting Length: 50 mm Maximum Cutting Length: 6000 mm Minimum Diameter: 10 mm Maximum Diameter: 600 mm Maximum Wall Thickness: 15 mm
We are Sia mechatronic, producing Paper core, edge board making machines since 2004. We are an experienced company with a great team which have global production experience. Our main office is located in Adana/Turkey, other remote offices in Istanbul/Turkey and many sales executive on the field. We are proud to inform you about our machines. For more information please contact with us! In addition, We have the ability to manufacture all kinds of paper machines and custom-made machines. Minimum Edge 20mm Maximum Edge 150mm Maximum Pipe Wall Thickness 8mm Minimum Cut to Length (20 m/min) 400mm Maximum Cut-to-Length 6000mm Maximum Cut-to-Length Speed 80 m/min Knife Cutting System Servo-motor Maximum Number of Layers 15 Pieces
Minimum pipe diameter 8mm (ID) Maximum Pipe Diameter 600mm (OD) Maximum Pipe Wall Thickness 18mm Minimum Cut to Length 150mm Maximum Cut-to-Length 6000mm Maximum Pipe Cutting Speed 30 m/min Maximum Number of Blades 10 units Maximum Number of Layers 35 Pieces PAPER BOBIN STAND 45 degree paper roll stand. Max 5-50 layers, or customized the layers. Paper roll distance 180 mm. Paper roll center adapter. Wheeled chassis. Chassis fixing screwes. PAPER GLUE STAND Pneumatic glue pump 150 Lt/min. Electrical glue pump 150 Lt/min.(Optionally) Electrical glue heater resistance with oil.(5 KW 3 phase) Mechanic paper breake Mechanic glue scraper PRE FORMING STAND Min.diameter: 10 mm Max diameter: 600 mm Min-thickness: 0,5 mm Max-thickness: 30 mm Rewinding noses: Two noses single belt Speed of adjust and control: Inverter Power input: 3x380V SERVO CUTTING STAND 6 Blades Pipe Cutting System with Servo Cutting Motor: 0,75 Kw (6 Pieces) Full Electronic Servo Controlled Length Cutting System Servo motor controlled blade cutting movement Min: 130 mm Max: 6000 mm Cutting Length Min: 0,5 mm Max: 15 mm Cutting Thickness Min: 20 mm Max: 250 mm Inner Tube Drawing Feature Smooth Cutting + - 2 mm Production Speed Min: Max: 30 meters / minute BELT CONEYOR STAND Belt motor 0.37 kw. Belt length 3000 mm. Belt width 300 mm. Belt motor with speed control. COLOR PAINTING STAND 1-Roll motor 0.37 kw. 2-Roll length 300 mm. 3-Printing width 300 mm. 4-Roll motor with speed control.
Max Paper Width: 850mm Max Speed: 250-300 Strokes/min Control System: Servo Motor Electric Power: 5 KW Net Weight: 2100 Kg Packed dimension: 3.15*1.8*1.9(L*W*H) speed: 180-250strokes/min PLC (Mitsubishi, Japan) Transducer (Mitsubishi, Japan) Servo motor (Mitsubishi, Japan)