The primary impact crushers make the less abrasive materials of medium hardness smaller with a high ratio. The materials from the quarry are processed with the primary impact crushers firstly. They have the ability to crush the materials up to 1 meter x 1 meter size to a size of 25 mm. There are 2 pieces of manganese coated adjustable crushing chamber. All surfaces that come into contact with broken stone covered with manganese undercoats. Crushing process is done with the 4 palettes of high-alloy manganese in a rotor weighing 8500 kg and rotating with 450 revolutions per minute.
Generally, these types of crusher are applicable to obtain the aggregate at the sizes suitable for production of asphalt and concrete. For these purposes cubic aggregate is preferred since the angular and rough surface has high binding properties. Impact crushers have an ability to reduce aggregate by 9 times and obtain cubic aggregate without weak or crack points. Generally, these types of crusher are applicable to obtain the aggregate at the sizes suitable for production of asphalt and concrete. For these purposes cubic aggregate is preferred since the angular and rough surface has high binding properties. Impact crushers have an ability to reduce aggregate by 9 times and obtain cubic aggregate without weak or crack points. Advantages: - Even at the condition of outworn of parts, continuously cubic material production; - High size reduction capacity; - Firm body; - High productivity with low energy consumption; - Easy maintenance and operation; - Low operating cost.
The Crushing and Screening Plant is 200-250 t/h and contains: Jaw Crusher 110 t/h Secondary Impact Crusher Vibrating Screen Conveyors Cabin and control panel and their cables TURNKEY!
PRIMARY IMPACT CRUSHERS ......... ........ ........ High percentage of cubical shape and close grain distribution Primary impact crushers are preferred for their high performance and high reduction ratios in crushing soft-character substances like gypsum and limestone. Due to the different principle of crushing these materials, the reduction ratio is higher than in jaw crushers. CRUSHER BODY Increased capacity with new crushing chamber design. Security sensor stops the system when the door is opened during maintenance. Lock systems prevent the machine body from closing down hazardously. Crusher body is manufactured with high-quality steel plate. WEAR PARTS Enhanced solid wear parts and liners. BREAKER PLATES Two independent upper and lower breaker plates allow the required size of the end product to be easily obtained, with protection system against blocking. BEARINGS Upper-class heavy-duty SKF bearings, with bearing temperature sensors. EASY MAINTENANCE FOR HIGH PERFORMANCE Crusher productivity is directly related to maintenance and safety. Primary impact crushers are equipped with modern solutions to make the maintenance process more efficient and to reduce maintenance duration. Primary impact crushers are equipped with a hydraulic lifter, which allows the user to open the crushers superior body for easy maintenance and easy access to the rotor, blow bars and wear parts. REDUCED OVERALL OPERATIONAL COSTS The liners of the crusher do not wear out at the same pace, so some of the liners may need to be replaced earlier than others. Primary impact crusher liners are designed to be interchangeable, meaning less inventory space is needed and reduced inventory cost for our customers. The blow bars are also designed to be reversible for the same reasons.
PRIMARY IMPACT CRUSHERS ......... ........ ........ High percentage of cubical shape and close grain distribution Primary impact crushers are preferred for their high performance and high reduction ratios in crushing soft-character substances like gypsum and limestone. Due to the different principle of crushing these materials, the reduction ratio is higher than in jaw crushers. CRUSHER BODY Increased capacity with new crushing chamber design. Security sensor stops the system when the door is opened during maintenance. Lock systems prevent the machine body from closing down hazardously. Crusher body is manufactured with high-quality steel plate. WEAR PARTS Enhanced solid wear parts and liners. BREAKER PLATES Two independent upper and lower breaker plates allow the required size of the end product to be easily obtained, with protection system against blocking. BEARINGS Upper-class heavy-duty SKF bearings, with bearing temperature sensors. EASY MAINTENANCE FOR HIGH PERFORMANCE Crusher productivity is directly related to maintenance and safety. Primary impact crushers are equipped with modern solutions to make the maintenance process more efficient and to reduce maintenance duration. Primary impact crushers are equipped with a hydraulic lifter, which allows the user to open the crushers superior body for easy maintenance and easy access to the rotor, blow bars and wear parts. REDUCED OVERALL OPERATIONAL COSTS The liners of the crusher do not wear out at the same pace, so some of the liners may need to be replaced earlier than others. Primary impact crusher liners are designed to be interchangeable, meaning less inventory space is needed and reduced inventory cost for our customers. The blow bars are also designed to be reversible for the same reasons.
Thanks to excellent engineering and quality production, TTC ENGINEERING jaw crushers are among the most important machine types that make our customers lives easier. Jaw crushers reduce large rocks or ore by means of compression. Mechanical pressure is applied using the crushers two jaws; one is fixed while the other reciprocates. There are also primary and secondary types of these crushers. Jaw crushers are one of the most commonly preferred crushers due to their ability to crush all kinds of materials of any hardness, as well as their lowcost operation and easy maintenance.
We provide installation work and operational training for all of our equipment! Primary Impact Crusher is a first stage crusher with high production capacity and large input size ability. Being mostly used for soft and middle hard stone types, this crusher type can give final ready fraction product alone. Working principle of the crusher with upper and lower adjusted pendulums, allows the user to regulate output product size by opening or closing the distance between pendulums and rotor hammers. Primary Impact Crusher which is manufactured by SERMADEN under SPI equipment code can be of different models, depending on total production capacity and input size of the product. SPI 1410 /150-200 tph capacity / 1400*1000 mm rotor size / 185 kW motor power / 1000 mm feeding / 20.000 kg weight SPI 1412 /200-250 tph capacity / 1400*1200 mm rotor size / 200 kW motor power / 1000 mm feeding / 23.000 kg weight SPI 1415 /350-400 tph capacity / 1400 x 1500 mm rotor size / 250 kW motor power / 1000 mm feeding / 27.600 kg weight
---------Description--------- ! We provide installation work and operational training for all of our equipment! SMJC series Mobile Jaw Crushing Plant is one of the most preferred types of equipment acquired in modern day stone quarry manufacture works. Primary Jaw Crusher on mobile construction is a time-efficient, high capacity primary stage crushing plant with large input size and enduring for all abrasive stone types. Nowadays, this equipment is mostly used for continuously changing mountain quarries and construction sites, where products are crushed and used directly at the extraction site. Models of this mobile equipment type differs depending on input size of the stone and total capacity of the equipment: SMJC 60 (10m3 bunker, 500x2500mm feeder, 380x610mm jaw) 60-80 tph SMJC 90 (20m3 bunker, 950x3800mm feeder, 650x900mm jaw) 100-150 tph SMJC 110 (30m3 bunker, 1100x4650mm feeder, 850x1100mm jaw) 200-300 tph
---------Description--------- ! We provide installation work and operational training for all of our equipment! Mobile impact crushing-screening plant is a new generation solution for quickly changing stone quarries, which is capable to reach up to 400 tph production capacity on a single chassis. Intended specially for soft and middle hard stone types, this equipment gives final gravel and dust product with only single primary impact crusher. By means of feedback conveyor belt, the product that will stay above all product sizes on the uppermost screen layer, will be sent back to the initial stone feeding bunker and crushed again until the desired size is obtained. All parts of the equipment are installed on a same single chassis, giving the ability to transport the equipment with only single truck head. Models of this mobile equipment type differs depending on input size of the stone and total capacity of the equipment: SMPI 1410 (15 m3, 1000 x 1400 mm, 1600 x 5000 x 4 deck screen) 150-200 T/H SMPI 1412 (20 m3, 1200 x 1400 mm, 2000 x 6000 x 4 deck screen) 250-350 T/H SMPI 1415 (30 m3, 1500 X 1400 mm, 2200 x 6000 x 4 deck screen) 350-500 T/H
---------Description--------- ! We provide installation work and operational training for all of our equipment! Vertical Shaft Impact Crushing-Screening Line is a tertiary stage plant, which is used to finalize crushing process to receive much amount of sand size product, which is mostly used in concrete and asphalt batching plants. This line consists of primary loading hopper, which receives and sends the product to the crusher, where crushed product is sent to the vibrating screen, sorted into fractions, and the oversize product sent back to the hopper via feedback conveyor. Feeding bunker 10 m3 Vertical Shaft Impact Crusher 800 mm Vibrating screen 2000x6000 mm (3 deck) Feel Free To Contact Us For Any Additional Information!
---------Description--------- ! We provide installation work and operational training for all of our equipment! Fixed Crushing-Screening & Sand Washing plant is another type of mining equipment solution that is targeted for hard stone types with sandy physical composition like Riverstone, where sand separates from the stone after the crushing process and neeeded to be washed away. After completion of crushing process, the product is sorted into necessary fractions and the smallest size product is sent to the helix/screw sand washer and after to the final stockpile conveyor belt. The process of washing that begins at the vibrating screen with the use of water pump tubes at each layer, continues at the sand washer, therefore sending both sandy water and sorted product to the helix washer. Depending of initial stone size, jaw crusher can be added at the primary stage. In our case, the stone is smaller than 400 mm, therefore we use secondary impact crusher and vertical shaft impact crusher. Crushing-Screening Line consists of: Secondary Impact Crusher 1120 x 1500 mm Vertical Shaft Impact Crusher 900 mm Inclined Vibrating Screen 2000 x 6000 mm (2 pcs) 600 x 6000 mm helix sand washer (2 pcs) Main, stockpile, feedback conveyor belts All intersystem electrical cables Control panel with control system Feel Free To Contact Us For Any Additional Information!
---------Description--------- ! We provide installation work and operational training for all of our equipment! 500 tph Jaw Crushing Plant is a fixed type primary stage crushing-screening line. Being the largest jaw crusher model in our manufacture, this crusher has a capacity up to 500 tons per hour and input feeding size ability up to 1-meter stone pieces. Being a special project for our customer, primary stage jaw crusher output conveyor goes 40 meters long with a special holding suspension bridge, making a necessary height for the product to be stocked underneath. Later, this gathered product is sent to the secondary stage by tunnel system vibrating feeder. Crushing line consists of: SJC 130 jaw crusher - 1000 x 1300 mm Suspension bridge conveyor belt 1200 x 40.000 mm Stockpile system underneath vibrating feeders 1200 x 5000 mm (3 pcs) Feel Free To Contact Us For Any Additional Information!
---------DESCRIPTION--------- ! We provide installation work and operational training for all of our equipment! Fixed Impact Crushing & Screening Plant dedicated for big capacity manufacture quarries with middle and soft stone type, especially with less abrasiveness. Crushing-Screening line consists of: Main Feeding Hopper with Vibro feeder -- 35 m3 Primary Impact Crusher -- 1400 x 1500 mm Secondary Impact Crusher -- 1120 x 1250 mm Preliminary Vibrating Screen -- 2000 x 6000 mm (2 decks) Inclined Vibrating Screen -- 2200 x 6000 mm (4 decks) Ready product stock hoppers -- 7 m3 (3 pcs) Control cabin and control panel All internal connections power cables.
--------Description--------- ! We provide installation work and operational training for all of our equipment! 250-300 t/h Fixed Impact Crushing-Screening Plant is the type of line, which has many different stage models, which differ by capacity, input product size, output product size proportion and shaft position. Impact crushers perform shredding by fast rotation of hammers, that are fixed to the shaft, where product is bounced between wall and hammers at an enormous pressure. This process at the end results with some amount of spare parts wear, which include rotor hammers, side liners, adjustable wall pendulums etc. Accordingly, impact crushers are mostly preferred for soft and middle hard stone types like limestone, gypsum, marble, slate, talc, soapstone etc. Equipment consists of: 25 m3 primary feeding bunker 1250x1400 mm primary impact crusher 1120x1250 mm secondary impact crusher 1200x4000 mm preliminary vibrating screen 2000x6000 mm main vibrating screen Feel Free To Contact Us For Any Additional Information!
---------Description--------- ! We provide installation work and operational training for all of our equipment! Fixed Jaw Crusher & Fixed Secondary-Tertiary Impact Crushing-Screening line, required for middle hard and abrasive stone types. Composed of primary jaw, secondary impact and tertiary impact crushers, this equipment is targeted to receive completely ready aggregate product used in concrete batching plants and other construction areas. Using secondary impact crusher gives cubic shape gravel size product at the output and tertiary impact crusher fine dust product, both of which are demanded aggregate types of concrete batching plants. Depending on usage area, tertiary impact crusher can be disables, receiving only output product of secondary impact crusher. Crushing-Screening Line consists of: Primary Jaw Crusher SJC 110 - 850 x 1100 mm Secondary Impact Crusher SSI 1112 - 1120 x 1250 mm Tertiary Impact Crusher STI 1210 -1200 x 1000 mm By-pass Vibrating Screen SVS 1240 - 1200 x 4000 mm Conveyor belts Product Vibrating Screen SVS 2260 - 2200 x 6000 mm Control cabin and control panel All internal connections power cables. Feel Free To Contact Us For Any Additional Information!
Crushing plant.
Ugur Makina UMA-110 series Mobile Primary Jaw Crusher Unit has been designed to meet the needs of our customers with compact solutions such as hydraulic feet, foldable conveyor and bunker chamber options that provide the advantage of easier installation in a shorter time. With its high capacity and performance, it ensures that all needs are met. The Mobile Primary Jaw Crusher Unit is shipped in accordance with international shipping standards. Technicial Specifications Model: Uur Makina UMA-110 Capacity: 100-300 t/h Feeder type : UMG03 - 2x8kw Bunker Volume: 1 unit - 30 m Crusher Type: 1 unit UMK110 - 132kw Crusher Output Band: 1200x8000 - 11kw Uur Makina UMA-110 Mobile Primary Jaw Crusher Equipment: Primary Jaw Crusher (UMK110) Vibrating Feeder UMG03 Mobile Chassis with axle and tires Hydraulic Feet Folding Type Belt Conveyor Please CALL us for our other Crushing plants and customer-specific solutions
Stone crusher, ball mill, belt conveyor, seperator, grinding plant, grinding equipment, dryer.
Concrete bathing plant, concrete pump, rock crushers.
Mining machinery manufactures, cone crusher, impact crusher, tertiary crusher, vertical shaft impact crusher, voluble crusher.
