Stock bunkers are collecting elements which do stock the crashed and then produced material through the pneumatic controlled covers without letting them fall down to the ground and load them to the truck. In addition to standard stock bunkers we produce bunkers in desired volume and sizes.
These breakers, which are used as primary and secondary, are ideal crushers to break the materials with high mohs hardness (materials of river and basalt). They break the materials by compressing them with two fixed and movable jaws. If the materials into the machine are hard to be broken, then the jaw crushers do not harm themselves through the safety plates which will be broken in a certain load. The main body is manufactured from tension and high-pressure resistant sheets/materials. Material crusher jaws and side liners are produced from the 16% - 18% manganese, 1.5% molybdenum alloy steel castings.
PSK series crushers, which are jaw-adjusted impact crushers, are crushers that break medium and high hardness materials (such as limestone, dolomite, granite and basalt) in the size of asphalt and concrete aggregate. Coarse material feeding, cubic product, high reduction ratio, high capacity, low investment and operating cost have made this type of crusher the ideal secondary crusher in crushing and screening plants. The stone entering the crusher hits the crushing elements in the first region with the swing of the rotor hammers and the first crushing stage takes place. In this region, high pressure and breaking power are created to break even very hard materials. If the crushed material is in the desired dimensions, it passes to the second zone. The material passing to the second zone passes through another crushing stage and is reduced to smaller sizes. Then the material passes to the third and last zone and the final crushing process takes place. Now the material is reduced to the smallest dimensions. ADVANTAGES Wear-resistant crushing elements High crushing capacity High reduction rate Hydraulic body opening Possibility to use both sides of the pallets
Elastomeric bearings consisting of a solid block of vulcanised elastomer without internal cavities are called plain pads. Plain pads are economical efficient support for precast and pre-stressed concrete or steel beams in bridges and buildings. These pads are designed according to required standards and shear modulus of the manufactured elastomer may vary between 0.6-1.35 MPa to meet the customers need.
Colour: White Size: R=2,5cm x 3cm H=2cm Purity: 97% Package terms: 25kg /50kg /Big Bag HS-Code:2501.00 Source: Turkey Production Stages: Refined/Washed/Dried/Pressed
Colour: White Size: R=2.5cm H=2.5cm Purity: 99.8% Package Terms: 25Kg/50Kg/Big Bag HS-Code: 2501.00 Source: Turkey Sector: Water Softening Production Stages: Refined/Washed/Dried/Pressed
- FULLY-AUTOMATIC SPREADING Specific to the automatic models with precise flow adjustment and specially designed spray-bar, perfect spreading can be made. The system works by reading the data such as vehicle speed and spread width by providing instantaneous pump flow for the desired amount of spreading. Spreading width can be increased or decreased during operation, the operator can accelerate or slow down according to the condition of the road, while the operator is focused on the driving system can start, maintain, and finish spreading. - COMPLETE CONTROL FROM CABIN Thanks to the specially designed control panel located in the operator's cab, the operator can get all functions such as circulation, automatic/manual spreading, intermediate pump feature, system cleaning, as well as controls such as pneumatic spray-bar locks, positions, paving width and spray bar movement of the spray bars. - ASPHALT PUMP The body of the asphalt pump is designed to remain in the tank so that freezing in the pump is prevented. Thanks to the internal valves on the pump, the system performs all functions without the need for a complicated piping system. Maintenance and cleaning are provided much more quickly and easily. - PUMP FUNCTION With a dedicated Asphalt Distributor Pump, critical functions can be performed with valves that are located both inside the pump and at the piping. Pneumatic actuators can be controlled directly from the cabin. Re-Suction TankFilling Tank Circulation Automatic / Manual Spraying Tank Discharge Intermediate pump (allows the transfer of the material from one source to another without mixing with the material in the tank using the Distributor) â?¢ System Cleaning - SAFE & FAST HEATING 8 diameter 2 flame tubes are placed along with the tank in U format. With 2 units of the electric burner, the material is heated quickly and efficiently. - SOLID MECHANICAL JOINTS The mechanical joints are important for the sealing and long-life use of the spray bar. Connectors used in the VAD Series asphalt Distributor allow the entire spray bar to be raised, lowered, or moved sideways. - OPTIONAL THERMAL OIL SPRAY-BAR HEATING SYSTEM The oil is heated by using the burners in the bitumen tank and transmitted to the spray bar. This eliminates the risk of material cooling during and after the spreading. - WORLDWIDE DELIVERY AND ONSITE INSTALLATION VAD Series Asphalt Distributors are designed according to the request of our customers to be suitable for their own countriesâ?? new or second-hand trucks. So, the high truck import expenses will be reduced. VAD Series can be put pre-montaged into a 40ft container thanks to this design transportation costs are reduced significantly and it took only 5-7 days for the installation and training.
Tertiary impact crushers are high-speed machines that are used to obtain sand. The material entered into the machine exits the machine after that it is hit against the walls and crushed by a high-speed (800 r / min) rotor. The material generally left over the screen is broken in these crushers, which usually are used to obtain 0-5 mm sand.
VSI crushers are the tertiary type of crushers used to crash the hard and abrasive materials between 0-45 mm, bring them into cubic shape and obtain sand. VSI crushers are produced in two types as closed rotor and open rotor. The vertical shaft types of crushers with closed rotor are fed with stones maximum size of 0-45 mm. because some large material in return of the crashed material can leave on the screen; these types of crushers are not suitable for crashing the returned material. VSI crushers shoot and crush the material, which entered into the rotor, by throwing them to the lining of stones "stone box" which formed in the stator naturally and to the materials which entered in the system from the outside of the rotor with a speed of 67 - 80 m / s approximately (crushing stones by hitting stones). VSI crushers are used to crush the materials having hardness lower than the grade 9 with a moisture content of less than 9%. Non-flammable and non-explosive mining materials have to be used.
Vibrating feeders are with each other synchronized two pieces of feeders which built solidly, supported with heavy duty suspension springs, driven/actuated by vibromotor, these feeders enable the transmission of the tuvenane materials, brought from the quarry, into the primer crushers in an orderly manner. They throw the mixed soil part of the tuvenian material outside of the system through the intermediate size adjustable grids on the front part of the feeders which coated with mangan. By demand, the loss of materials can be included in the system again after screening them with a suitable screen it is possible. The feeding capacity adjustment of vibromotor vibrating feeders, produced by us, can be made. Thus, the primary machine is fed regularly, and again there is no need to stop and run the machine continuously.
Concrete Batching Plant And Spare Parts Concrete Pump Spare Parts Truck-mixer Spare Parts Tower Crane Spare Parts Used Concrete Machinery And Tower Cranes
Panel type made of 304 grade stainless steel Flexible production in different designes and dimensions, It has been produced for the purpose of preserving the integrity of the body for a temporary period of time until the body of the Ex (deceased) burial process is done. Thickness boards 60mm. Polyurethane foam insulation between two 80 mm thick stainless steel plates, the density of polyurethane is 38-42Kg / m3 Front doors with locking system, doorsâ?? dimensions: 610mmx650mm The interior lighting which switches on when the door is opened, â?¢ Digital heat indicator and control system, â?¢ Temperature Range : 0 to +5 degree Celsius â?¢ R 404A gas Completely manufactured from 304 grade stainless steel trays with 1.2mm thickness, easy loading and unloading facility by rollers. Fully automatic defrost, internal cooler with fan-controlled that has 1400kcal capacity, drain hose forcondensate, Convenient displacement and cleaning with 4 wheels in diameter of 125mm
Bearing Housings In our company, many kind of bearing housings are manufactured. We are manufacturing bearing housings with our experience of being in the sector for many years and our knowledge of steel sheet deep drowning. Bearing housings are produced by metal sheets and they are also suitable for bearing bore. Labyrinthed housings protect bearing from moisture, dust and other hard conditions. It causes long life service. We have also polyamide tight fitted bearing housings. You can find our housing table below.
In Turkey/Hatay
hydraulic adapters
hydraulic fittings
hydraulic fittings
Elastomeric bearings reinforced internally with one or more steel plates, chemically bonded during vulcanisation are called laminatid elastomeric bearings. Elastomeric bearings permit a smooth and uniform transfer of loads from beams to substructure and also allow beam rotations at the point of support due to deflection of beam under loading. They further allow lateral and longitudinal movement of beams caused by thermal forces. Elastomeric bearings have no moving parts and thermal expansion and contractions are supported by shear capacity of elastomers. There is no sliding motion between bearing and beam or between bearing and abutment.
These isolators are similar to the previous but with the exception that the dissipation of energy is obtained also through the use of one or more lead cores. Lead (used here at a level of gg.go% purity) has the property of undergoing plastic deformation as it dissipate energy and then re-crystallizing after a cycle of plastic deformation. Because of this, it is able to sustain an unlimited number of hysteresis loops.
The bearings we have defined so far are the basic types, which constant feature is the fact that they allow all-ways movements and rotation. However, movements can be limited in one or all ways, thus obtaining guided or fixed bearings, respectively. In the first case -guided bearings- the restriction is obtained by means of guides parallel to the supporting axe that allows movement. To make friction as low as possible, PTFE and stainless steel sheets are welded to the guides.
