Lithium Battery Separator/ Electric Vehicle Air Permeability Tester Gurley Method Product Detail Application: Based on the differential pressure method, and is professionally applicable to the determination of gas transmission rate as well as solubility coefficient, diffusion coefficient and permeability coefficient of plastic films, laminated films, high barrier materials, sheeting, metal foils, rubber, tires and permeable membranes. Lithium Battery Separator/ Electric Vehicle Air Permeability Tester Gurley Method Features: Vacuum differential pressure method Own technology 3 specimens test simultaneously and independently Computer control One-button test, test automatically through whole process High accuracy vacuum sensors embedded in 3 Chambers with independent temperature sensor Test under various RH conditions with Humidity generator (optional) Environment temperature and humidity sensor inside Permeability coefficient ,solubility coefficient and diffusion coefficient test Chambers with water bath temperature control technology Unit based on embedded system,24bit AD Multiple test modes optional Data curves display Traceable reference film calibration Supports DSM system (DSM, lab data management system)
API 7k Casing Manual tong Product information 1. Structure of Casing Mannual Tongs Description The casing tongs are designed and manufactured in accordance with the API Spec 7K Specification for Drilling and Well Servicing Equipment and the National Standard for the Petroleum Gas Industry SY/T 5035 Elevator Links Elevators and Tongs which is a useful tool applied to make up and break out drill pipes, coupling hoop of the drill pipe joint casings casing hoops etc. When raise drill tool up and fall it down. Changing hinge jaws and handling shoulders of latch lug jaws can adjust the handling size of the tongs. 2. Main Features 1) API standard; 2) Very Good Quality; 3) After-sale Service.
The lightweight Lubricators enable the wireline tool string to be introduced or retrieved from a well bore under pressure. The lubricator can be used singly also can use multiply according to the requirement of the oilfield operation, but the seal control head always be assembled on the top of the lubricator. Single Lubricator is 0.8-3m, the number of lubricator and total length could be decided by operation. Titanium alloy Lubricator is much better quality and lightweight than normal steel materials. The lightweight Lubricators usually consists of four basic parts: a quick union collar, a male quick union, a lubricator tube, and a female quick union.
The lightweight Lubricators enable the wireline tool string to be introduced or retrieved from a well bore under pressure. The lubricator can be used singly also can use multiply according to the requirement of the oilfield operation, but the seal control head always be assembled on the top of the lubricator. Single Lubricator is 0.8-3m, the number of lubricator and total length could be decided by operation. Titanium alloy Lubricator is much better quality and lightweight than normal steel materials. The lightweight Lubricators usually consists of four basic parts: a quick union collar, a male quick union, a lubricator tube, and a female quick union.
CMS-XL Casing Slips are made up of body segments of the same sizes linked up by Hinge Pins.Adding or reducing body segments and changing button inserts according to the specification can suit different sizes of casings pipes.The buttion inserts can be used in both Casing Slips and Drilling Collar Slips.Eight different kinds of button inserts will satisify all needs. 1.Casing Slips can accommodate casing from 65/8 to 30 inch (168.3-762mm) O.D. 2.Full range of Replacement Part
Factory best price XQ28 sucker rod tong hydraulic power tong 1. Summary Model XQ28/2.6 hydraulic power tong is an improved type of XYQ1.8 which is used to make up and break out sucker rod thread in Well Service. This product has the following features: A. The structure is compact ,concise and light.Master tong is driven by low speed large torque hydraulic motor which matching with manual control valve. The backup tong just like a spanner. Total weight is approximately equal to XYQ1.8. B. The operating is briefness and convenience with high efficiency. Put the respondence size jaw set into master tong and the respondence size glutting into backup tong , turning the reset knob in correct direction then can make up and break out sucker rod by operating manual control valve. Two speed,snapping at low speed, spinning at high speed . C. Large low gear torque,especially suitable for the instance that is difficult to break out sucker rod thread.
Safety Glass Testing Method Impact Testing Equipment Testing Machine for Mechanical Properties of Tempered Glass Mechanical Testing Equipmentï¼? Shot Bag and Impact Device, Hardware Steel Ball and Ball Drop Device, Headform and Test Stand, Pneumatic Tyres Impactor, Pendulum Shock Device for Electric lifts, Impactor for building Glass and Metal Guardrail, Hard and Soft Impactors for Opaque Wall Components, Whole Soft Heavy Body Impactor for Doorsets. PV module Static Load Test Equipment Pummel Machine, PVB Boiling Device, Dew Point Meter, Glass Flatness Measuring Instrument.
CNDIP Full Set 40 Pieces Common Rail Injector Dismounting Tools Box DIP (Diesel INJECTION PARTS) PLANTS is a manufacturer specialized in diesel fuel injection parts & components. The product line includes Injection Nozzles, Pump-elements (Plunger Barrel), Delivery Valve, Head Rotor,VE Pump Parts and many other related products. Our Advantages 1. High quality,Best price. 2. Timely delivery; Within 7 days after confirmation. 3. Stable performance, Safety and stability,Long-standing durability. 4. Warranty: 6 months. 5. Packing customization: Accepted
Steel Ball Drop Impact Tester Function: Determination of whether the safety glazing material has a certain minimum strength and cohesion under impact from a small hard object Suitable for impact test of safety glass and tempered glass. Related Standard: ISO 3537 Road vehicles Safety glazing materials Mechanical tests Clause 6: 227 g ball test, Clause 7:2260 g ball test GB 15763.3 Safety glazing materials in building Part 3:Laminated glass Appendix B Drop ball impact specimen support Apparatus: 1) 1m/3m/5m Ball Drop Impact Testing Device 2) Adsorption and release device of steel ball 3) Steel ball 4) Supporting fixture size: 350 mm*350 mm or 660 mm*660 mm Technical Data: Hardened steel ball: 2260g ± 20g, diameter of approximately 82mm 1040g ± 10g, diameter of approximately 63 mm 227g ± 2g, diameter of approximately 38 mm Steel ball adsorption mode: Electrocircuit controlled electromagnet suction cup Lifting and lowering mode of control lever: manual or automatic Drop height of steel ball: 1m /3m/5m/12m, customizable Supporting fixture: Support size: 350 mm*350 mm and 660 mm*660 mm (Customized) Frame width: 15 mm Steel box height: 150 mm Rubber gasket: thickness 3 mm, width 15 mm, hardness shore A50 Interposed sheet of rubber: thickness 3 mm, hardness shore A50 Applied Test Pieces Size: 300 mm*300 mm and 610 mm* 610 mm
LAKE Reverse Circulation Junk Basket (RCJB) is designed to remove all types of small junk objects from the hole. The tool�¢??s main feature eliminates pulling a wet string. Even when the tool is fitted with a magnet insert, reverse circulation is maintained. Operation: LAKE Reverse Circulation Junk Basket is made up to the bottom of the fishing string and lowered to a point within several feet from the bottom of the hole. Begin circulation to wash the hole. Stop circulation and drop the steel ball. (When the steel ball is dropped into the valve seat, circulation fluid travels outward and downward through the inner passage of the barrel and out through the vents in the lower end. The fluid is then deflected to the center of the tool and up through the return holes in the upper end of the barrel. This reverse fluid circulation carries the junk into the barrel above the junk catcher.) Begin circulation again, slowly rotating while lowering the tool until a 10�¢?? core has been cut. Stop rotation and circulation and pull the tool from the hole.
Air winch is a kind of manual operated single drum type air winch. It adopts compressed air as its power to drive air motor to drive air motor, driving drum via two grades gears ( to reduce transmitting speed and enlarge torque) so as to lift and drag heavy cargo. Considering security, this winch is specially designed with hand brake and foot brake. This winch is widely used for drilling, marines, minings, engineering sites, etc to pull heavy cargo. Features: 1. Small in size, light in weight, high in mobility. 2. Variable speed control, flexible to perform clockwise and anti-clockwise rotation. 3. High practicability with anti-explosive function, especially stable and reliable in inflammable, explosive, wet, damp, and other extremely working environments. 4. High starting torque enables start with load. 5. Anti-overload function. Technical Parameters Technical Parameters for JQHSA15 Air Winch (1.5T): Items Parameters Model JQHSA15 Working Air Pressure (Mpa) 0.7-0.9 Capacity at the First Layer (kN) 15 Rope Speed (m/min) 0-8 Piston Air Motor Rated Power (kW) 4 Air Consumption (L/s) 130 Drum Diameter (mm) 175 Width (mm) 200 Wheel Rim Diameter (mm) 350 Rope Diameter (mm) 11 Rope Storage (m) 80 Air Inlet Diameter (inch) 1 Brake Type Auto Disc Brake Dimension Length (mm) 930 Width (mm) 350 Height (mm) 600 Net Weight (kg) Approx. 190 (Not Including the rope) Filter, Lubricator, Silencer Yes
Product Description Detailed Product Description: Automatic Trip Hammer is produced as per BS1377: Part9:1990 for carrying out the Standard Penetration Test (SPT). The Automatic Trip Hammer comprises following parts: a) A weight made of steel and provided with an axial hole with a diameter which is 3 mm to 4 mm larger than that of the guide rod. It is of 63.5 kg. b) A pick-up and release mechanism to ensure that the weight has a free fall of 760 mm and shall not influence the acceleration and deceleration of the weight or the rods. c) An inner guide shaft to permit the weight to drop with minimal resistance, and to ensure the weight strikes the anvil squarely. d) An anvil made of steel with an integral threaded portion to connect squarely and rigidly on to the top of the uppermost extension rod. In order to carry out the Standard Penetration Test (SPT) to BS 1377:Part 9:1990. The Auto Trip Hammer, SPT Drive Rods and a Split Tube Sampler are worked together. Technical Parameters The basic operation of the complete set Standard Penetration Equipment are like the following sketch shows. Description of goods: SPT Split Tube Sampler is for doing the Standard Penetration Test (SPT). We manufacture it according to BS 1377: Part 9: 1990. A Top ball valve Adaptor, a pair of Split Spoons, and an open SPT Shoe compose a complete set of SPT Sampler. Both plastic type and steel type basket retainers are available. The ball valve adaptor prevents sample from being washed out of the sampler when the sampler is withdrawn from the borehole. A 60 degree nose cone and long solid rod with 60 degree point are available as well. The screw connection on the top adaptor depends on the type of drill rods being used to drive the sampler, but is most frequently 1.1/2" B.S. Whitworth, NWY Rod, BW or AW Rod. Split Spoon compose of Sample Spoon Head, Split Tube, SPT Adaptor, SPT Shoe. The standard Split Tube Sampler is 2" (50.8 mm) OD x 1.3/8" (34.9 mm )ID x 18" (457mm)/ 24" (610 mm) long. For heavy driving conditions, the Heavy-duty "Tuflok" design is available. Components: 1. Ball Valve Adaptor 2. SPT Solid Rod 3. SPT Nose Cone (2). Split Tubes (3). Basket Retainer (4). SPT shoe
Diagnostic Instruments. Buck Percussion Hammer. Size: 18.5 cm 7 1/4" with needle and brush.
Amar Instruments manufacturing and export all kind of Ophthalmic blades / knives and miniature blades / knives at very reasonable price , for more details please log on or email us at ( info (AT) amarinstruments.com ).
Function: Measurement of arcuate form and wave form of tempered glass Related Standard: 1) GB 15763.2 Safety glazing materials in building Part 2: Tempered glass Clause 5.4 Camber measuring 2) AS NZS 2208 Safety glazing materials in buildings Clause 2.5 Flatness requirements Technical Data: Resolution: 0.01 mm Measuring Span: 30 mm-1000 mm ( Customizable) Working Temperature: 0~+40C Working Humidity: 80% We provide exquisite packaging customized for customers. Instruction: Adjust the measurement and set up to track the maximum data. Adjust the span of the support block according to request. Adjust the position of measuring head, to ensure that the measuring head is beyond 2mm-3mm of the plane of three support feet. Gently stick the surface of the glass to ensure that three supporting feet are able to touch the glass. Slide the measure location and read the data. Product Features: Continuous measurement and monitoring of the flatness of the glass, data display and recorded. Simple operation, fast measurement, low cost, widely used in the flatness measurement of glass. The specifications of the equipment are various; the measuring span (300 mm, 500 mm, 800 mm, 1000 mm) can be customized according to customers requirements.
Safety Glass Impact Test Device - Headform Impact Test Device Related Standard: ISO 3537 Road vehicles â??Safety glazing materials â?? Mechanical tests â?? Clause 10 Head-form test Principle: Assessment of the minimum strength and cohesion of the safety glazing material under impact from a blunt, bulky object. If required, tests can be performed on whole windscreens. Application: The purpose of this test is to verify the compliance of glazing with the asking relating to the limitation of injury in the event of impact of the head against the windscreen, laminated glass and glazing of glass-plastic and rigid plastic other than windscreens, together with The double-glazed units used in the side windows. Technical Data: Head-form Weight: 10kg Head-form Size: 500mm*932mm Impact height: < 1.5m Samples size: 1100mm*500mmw Felt hat: 90g/89mm Thickness:5mm Frame size: 1376mm*670mm*320mm Apparatus: Head-form weight, with a spherical or semi-spherical head made of laminated hard wood covered with replaceable felt and without a cross-beam made of wood. Between the spherical part and the cross-beam, there is a neck-shaped intermediate piece and on the other side of the cross-beam, a mouning rod. The total mass of the apparatus shall be 10 kg�±0.2 kg Supporting fixture: for testing flat test piece, the fixture is composed of two steel frames, with machined edges, 50mm wide, fitting one over the other and faced with rubber gaskets 3mm�±0,5mm thick and 15mm�±1mm wide, of hardness 70 IRHD. The upper frame is pressed against the lower frame by at least eight bolts. The support shall rest on a rigid stand with a sheet of rubber, of hardness 70 IRHD and 3mm±0,5mm thick, placed in between.
Amar Instruments AN ISO 9001-20016 Certified and CE Product Company, manufacturing and exporting our wide rang of Ophthalmic Blades / Knives and Miniature Blades / knives entire world, more details please log on
VCF series MECHANICAL Vernier calipers available from 0-130mm to 0-980mm with fine adjustment. Measures OD, ID, Step and Depth. Robust, hardened and ground SS jaws & beam.
Digital Internal Micrometer Features : Measuring range: 300-500 mm, New constant force digital readout, Single 300 mm setting ring covers full range And Radius anvils of tool steel for optimum centering.
The model is hydraulic design and chain driven. The main parts are imported from USA with global warranty. It is powerful to carry bricks, sand, stones, wood, crops, fruits in various sites.
