1. High power and super suction, more thorough dust absorption, can be washed and filtered haipa, dry and wet dual use, car charge power supply, 3 meters above long line, where to suck, large capacity dust bucket, more garbage, office, car, home can be used. 2. High-power super suction, more thorough dust absorption, equipped with efficient and strong DC motor, the strongest suction can be up to 7000Pa, unique motorTurbocharged aluminum blade design, can prevent overheating, deformation, abnormal sound smell, can easily absorb melon seeds, potato chip residue, hair, dust,scraps, coins, etc 3.2 Layer filter system + washable hypa. The primary filter can intercept large particles of dust and residue, while the second layer HEPA filter can pass through Filter dust as small as 0.3 micron, effectively prevent secondary pollution, dust cup and two layers of filter can be washed, can avoid excessive dust adhesion cause congestion. 4. Large capacity, translucent visual dust bucket, one key split design, convenient and easy to use, the dust and garbage inside can be poured out. 5. The body is only about 1kg, equivalent to a two-month-old baby cat. Even with all kinds of vacuuming tubes, it won't weigh much, girl It is also easy to use. 6. Air vents on both sides, ingenious design, effective noise reduction, there are children asleep in the car, also not affected.
Electric drill toolbox, hardware tool set, household power tool set
Cable Harness Probe Pogo Pin CHL165-HQ(8.3) for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHL165-HQ(8.3) harness probe we will introduce here is 1.65 mm in diameter and 35.8 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 100 milliohms. It is suggested the plunger be pressed at a distance of 3.5 mm at most when this probe works, although the plunger can move as far as 5.3 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 3.5 mm, its loaded force is about 113 gf, namely 4 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 100 milliohms Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 113�±35 gf (4 oz) at load 3.5 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Pogo Pin Semiconductor Test Probe SCPC028 Applied to IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC028 we will introduce is 0.28 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottom plunger is made from beryllium copper plated with nickel and gold. The top plunger is made from SK4 plated with nickel and gold. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1.05 mm. But it is better to be pressed at a distance of 0.7 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.7 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Phosphor Bronze/Gold Clad Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 150 milliohms max Bandwidth: 8.5 GHz at -1dB Inductive Reactance: 1MHZ at -0.0788 uH Capacitive Reactance: 1MHZ at 0.3165 uF Specifications: Full Stroke: 1.05 mm Rated Stroke: 0.7 mm Spring Force: 25�±7 gf at load 0.7 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
EP800 Series Electro-Pneumatic Positioner All model is including:EPA800 Single action,EPC800 Double action,EPB800 for 5200LA actuator Which is used with pneumatic actuator, input 4ï½?20 mA DC The signal is converted into the output air pressure to control the action of the actuator. At the same time, according to the behavior of the executive agency Feedback from the stroke, so that the stroke of the actuator can be accurately positioned according to the control signal. EP800 Series electro-pneumatic positioners can be used for single-action and double-action pneumatic actuators. FEATURES USABLE WITH LOW TO HIGH CAPACITY ACTUATORS By adjusting the built-in capacity control spring, the positioner can be made optimum to the given actuator. A LOW AIR CONSUMPTION The pilot valve is low in air consumption and high in capacity. OUTPUT CHARACTERISTICS SELECTABLE Having a cam within the feedback construction, choices other than the standard linear characteristic are available. COMPATIBLE WITH VARIOUS FEEDBACK TYPES Applicable to the following types by simply exchanging the cam block. * For Linear type actuator : Feedback for Standard lever type EP 8 1 * For Rotary type actuator : Feedback for lever type EP 8 2 * For Rotary type actuator : Feedback for direct connection to driving shaft EP 8 4 REVERSE ACTION PILOT VALVE EASILY AVAILABLE The positioner for double acting actuators can be used as a reverse action pilot valve when combined with a spring return actuator that requires a reverse action pilot. ANTI-PRESSURE AND EXPLOSION PROOF STRUCTURE MARKING ON-SITE ADJUSTMENT POSSIBLE The anti-pressure and explosion proof construction, with the terminal and coil blocks enclosed together in one package, makes it possible to remove the positioner cover for inside inspection or span adjustment even in an explosive ambient. INTRINSICALLY SAFE CONSTRUCTION FOR A WIDE SCOPE OF APPLICATIONS The intrinsically safe construction (torque-coil type: EP82) cover terminals and coil as one package. This, combined with The adoption of the specified zener barrier, makes the unit applicable in all hazardous gas location ( including Class 0 area) ranging from low ( 40 ) to high ( 60 ) temperature environment.
Interface Probe Test Pin IFP-001 Used for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-001, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-001 interface probe is 14.22 mm in total length. If customers wish to change its length or diameter, we could do as required. This probe is unique in shape. It is straight whereas others, for example 002, 003, 004, 005, 006, 007, have an extra base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information was founded in 1980. Â Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
In-circuit Test Probe Pogo Pin PE50 for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits.
Double-ended Pogo Pin Test Probe SCPA100 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA100 Â we will introduce is 1 Â mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Â Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production.
The automotive power system trainer integrates the working principle and structural composition of the new energy electric vehicle power system, and demonstrates the working process of each working condition of the power system. It is beneficial to students to learn the basic principles and structural components of the new energy electric vehicle power car power system....
The automotive power system training equipment based on the real components of the new energy vehicle battery pack assembly, including the power battery, battery management system, etc. the composition structure and working principle of the lithium battery of the electric vehicle can be truly displayed....
Circular Saw Blades Cold Saw Blade Hot Saw Blade TCT Circular Saw Blade HSS Circular Saw Blade Segmental Saw Blade Band Saw Blade Carbide Tipped Band Saw Bimetal Band Saw Shear Blades Shear Knives Peeling Knives
Test Equipment A340E Automatic Transmission training bench Product introduction Based on the electrically controlled automatic transmission of Toyota A340E, and with the speed-regulating three-phase motor as the power source, the training platform can perform the actual operation of various test
Semiconductor Test Probe Pogo Pin SCPB038 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFB038 we will introduce is 0.38 mm in barrel diameter and 6 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 100 milliohms max Bandwidth: 5.3 GHz at -1dB Propagation Delay: 27 ps Inductance: 1MHZ at -0.02809 uH Captance: 1MHZ at 0.876347 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.6 mm Spring Force: 25 7 gf at load 0.6 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
hand shoe tacks used in making furniture, shoes and for farstening things
ANTI-LOCK BRAKING SYSTEM TRAINER SIMULATOR Autotronics Fundamental and Advance Autotronics Simulator. 1. This trainer provides a realistic simulation of automotive anti-lock braking (ABS) electrical systems with real time results and modular panel layout. 2. The system...
The training bench is based on the Toyota A340 electronically control automatic transmission assembly and fully display the internal structure and working process of the electronically control automatic transmission. comprehensive function system, operating normally, and also...
Auto Trainers Electrical Teaching Board Engineering Educational Equipment - Buy Automotive Electrical Training Stands,Automotive Electrical Education Bench,Automotive Airbag Teaching Board Product on ZHONGCAI
Auto Trainers Electrical Teaching Board Engineering Educational Equipment - Buy Automotive Electrical Training Stands,Automotive Electrical Education Bench,Automotive Airbag Teaching Board Product on ZHONGCAI
Battery Contact Pin Test Probe BIP80 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP80 series of battery contact probes. The outside diameter is usually 0.8 mm and total length is 11 mm. There are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 1 mm Rated Stroke: 0.9 mm Spring Force: 60 gf (2.4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated
The device has an open design, is equipped with refrigeration pipeline equipment, and is equipped with various circuit schematic training boards. The electrical components required by the circuit are installed on the training board. Students can perform the refrigeration...
