DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CA-055 is an emulsion primer of water-based acrylic resin with excellent properties such as water resistance, pull-off strength and pore-filling ability etc. , especially used to improve the physical properties of cement. It can be mixed with water at any ratio. FEATURES Excellent penetration into the concrete substrate to increase pore-filling ability and adhesion. Reduced transport paths of concrete structure to enhance durability. Excellent water resistance. AREA OF APPLICATIONS Repair mortar for concrete areas. Industrial flooring. Bonding agent for new to old concrete. As cement grout additive. As water-based primer. For making two component tile adhesives. As adhesion aid for skim coat materials. PACKAGING 5 gallon Plastic Pails FLAMMABILITY Being water-base, it is non-flammable.
Description CP-121W(14) is suitable for new and old concrete floor with resistance and waterproofing ability. It has ability to penetrate in concrete, plaster or the surface of the stone for the building and to reach waterproofing. * Able to apply on the damp surface * Odourless and eco-friendly * Excellent resistance ability of negative water pressure (Comply with CNS1232. CNS10460. ASTM E96-12 B) * Enhance adhesion strength Properties * Leaking stoppage from basement inner wall * Waterproofing on negative water pressure * Anti-seepage for underpass, tunnel and water tank Application 1. Clean the surface to be free from loose particle, dirt and oil. 2. 3 options for application
Your own branded cordless brushless power tools, hand tools, automotive tools, garage tools, tarps, pliers, wrenches, torque wrenches, sockets, impact sockets, hex keys, screwdrivers, toolboxes, tool cabinets, hydraulic jacks, bottle jacks, wheel positioning jacks, wheel dollies, hand truck trolleys, shop press, engine crane, engine stands, parts washer, creeper, tie downs, straps, shackles and more.......
Tools.
Chemicals.
Nuts, screw.
Phycobiliprotein, recombinant protein.
Used circuit breakers and scrap used inverters used magnetic contactors used motors and scrap used scooters used cars engines used and new auto parts.
Cold forging, hot forging, stamping & assembly unit, investment casting (wax lost parts), injection molding plastic and rubber parts, fine blanking parts.
Ball valves/ butterfly valves/ Solenoid valves Fluid: water/ steam/ oil/ gas/ air/ vacuum OEM/ ODM available
Iron Anchor chain hanger 75cm 3 x S Hooks x 33mm/2.0mm dia 1 x S Hooks x 25mm / 2.0mm dia
Iron Anchor chain hanger 45cm 3 x S Hooks x 33mm/2.0mm dia 1 x S Hooks x 25mm / 2.0mm dia
Two sizes are available: 12mm/14mm. (Pediatric/Adult) High, Medium, Low pressure are available Features 1.Flexible silicone elastomer eliminating valve sticking and deformation. 2.Connector included. 3.Internal flow path is uncomplicated. 4.Two-way flushing eliminates separate reservoirs or antechambers. 5.Non-metallic design will neo interfere with CT scans or MRI. 6.Polypropylene needle guard prevents complete penetration of the valve by needles. 7.Slicone elastomer dome is injectable.
1. Patients position When patient lying down at horizontal position, pressure(high, medium or low) will be controlled via pressure membrane of the valve. 2. Function of slit valve When patients position is changing uplifting to vertical position(sitting or standing position), theres negative pressure caused by changing the posture. The fluid drainage will be controlled efficiently by the slit valve at the distal end of the Peritoneal Catheter. 3. Anti-siphon effect There are double pressure membranes to control the flow in only one direction and avoid over drainage by preventing siphoning effect.
Material: SUJ2 || Ball: G10 || C3/C5 Industrial: Semiconductor, Medical, Micro Movement Brand: Taiwan (Wei Tai Transmission Company) Inquiry data sheets: service (a) weitaitransmission.com
Measurement Equipment.
Dyes.Manufacturing
PP, PE, POE, TAFMER, PS, PC, ABS, PA, SBS, SEBS.
PVC, PP.
