Gas turbine.
Switching AC / DC adapter, switching power supply, battery charger.
No-load speed:13000r/min. Two-step Lock button; Handle Use Panasonic 3AH BATTERY Body diameter: 90*20*14cm(Short type)ã??126*20*14cm(Long type) Weight: 0.9kgs Blade material: S45C Blade Operating time:30~40 minutes
1. Varied battery management styles 2. 24 hours automatically monitoring 3. Wi-fi and hotspot connect method 4. High extensibility of hardware allows user to manage big amount of battery 5. B-TEK special forecast scatter chart 6. E-mail alarm notification 7. Monitoring item includes battery volt., temperature, DCR, micro-discharging volt. and EMF 8. B-TEK unique AI forecast function 9. Support Modbus TCP/IP, RTU and LAN method UPS system as the important equipment to the stable power supply needs a great amount of battery as a back-up power source. Due to the enormous amount of the batteries, it makes it hard to carry out the manual maintenance. To maintain the discharge ability during the outage, regularly manual detection is needed. However traditional battery discharge test needs battery offline. It's time-consuming and increasing the cost. BMS system can improve the risk of manual measurement, battery deterioration, and power failure, changing battery according to the actual condition of batteries. Besides, the automatic battery equalization function can extend battery life. Not only can it raise the reliability, lower the cost of battery failure, decreasing manual labor also increasing the stuff safety by avoiding direct contact with the electric device. BMU is installed to the individual battery, collecting the data and send it to the UMW to analyze. BMU is powered by the detected battery, therefore the extra power is not needed, This unit applies to a lead-acid battery, nickel-cadmium battery, lithium battery. BMU analyzes 5 parameters: terminal voltage, temperature, dc resistance, micro-discharging voltage, and electromotive force. Bu analysis, the system finds the deteriorated reasons for the battery and do the predictive maintenance. The groove on the back of BMU allows it to attach on the mounting rail. Dimension is 75*57*31mm. Reverse connection protection function will keep the internal circuit of BMU intact from a reverse connection. CMU connects to the charger and UMW. The main purpose is to monitor the current of the charger and the total voltage of the battery bank. The groove on the back of the CMU allows it to attach on the mounting rail. Dimension is 75*57*31mm.UMW provides the website browsing function, the user can access the real-time data, historical data, forecast scatter chart, line or curve graph through it. We can utilize a computer, mobile phone or tablet to remotely access the system through ethernet and hotspot function. Besides that, we can also use the FTP and VNC software to remotely access the data or control the system. When the system detects the abnormal parameter, it will automatically send the email notification and inform the users. Another AI function can provide a maximum of three years predicted data of the battery by analyzing the historical data. Efficiently manage the energy system Website: http://www.b-tek.com.tw/en/web/
EDAM-8530 ISO USB to RS-232 / RS-422 / RS-485 converter * Automatically switch USB signal to RS-232/RS-422 or RS-485 * Driver support for Windows 95/98/ME/2000/XP/Vista/7 * Power and activity indicator for troubleshooting * Auto switching baud rate up to 115.2 Kbps * Reserved space for termination resistors * Minimum 3000 VDC isolation protection * Mounts easily on DIN-rail or panel * Full-duplex RS-232/RS-422 support * RS-232 RTS & CTS signals support
EDAM-8531 ISO USB to RS-422 / RS-485(TX,RX,RTS,CTS) convert * Automatically switch USB signal to RS-422 or RS-485 * Driver Support For Windows 98/ME/2000/XP/Vista/W7 * Power And Activity Indicator For Troubleshooting * Auto Switching Baud Rate Up To 115.2 or 921.6 Kbps * Reserved space for termination resistors * Minimum 3000 VDC Isolation Protection * Mounts Easily On Din-Rail Or Panel * Supports RS-485 full(4-wire) / half(2-wire) duplex * RS-422 RTS & CTS Signals Support
7.4v 2300mah li ion battery pack with plastic housing; Integrated with protection circuit module; Integrated with gas gauge ic; Output: positive, negative, 10k ntc
12v 10s1p 3.6ah nimh battery pack; Low-self discharge rate type Integrated with ntc, thermal protector, pptc Lead out 3 wires with connector
3.7v 200mah li polymer battery pack Integrated with protection circuit module Lead out 3 wires with connector
Built-in shuttle knop to adjust output frequency easily Built-in rs-485 communication interface Support modbus and shihlin communication protocol Built-in proportion linkage control function to support multi inverters connection Maximum 650hz frequency output enable to support special and high-speed motors. Support din rail mount The resolution of frequency setting: digital 0.01hz ; analog 1/1000 The accuracy of output frequency: 0.01% Multi-function input/output terminals Support 2 analog setting types. 0-10v and 4-20ma
a. 7 months guarantee. b. All made in Taiwan. MOQ=50 pcs General specifications: ITEMS SPECIFICATIONS Battery cell Lithium Capacity 4400 mAh Output Voltage DC 5V Output Current 1.2A Charge time Approx. 5hr (Input Current 1A) Life cycle Over 500 times Operation temp. 0-50 Celsius Degree Dimension ( L) 76mm x (W) 67mm x (D) 26mm Weight 132g Accessory USB cable / connectors
Compatible with origin CANON, NIKON, OLYMPUS, FUJI, PENTAX, PANSONIC, SONY, NOKIA, SAMSUNG, MOTOROLA, SONY ERICSSION.....
Battery pack
Rm5g series Specification: 200~240v, 3 phase, 0.5hp~150hp (0.4kw~110kw) 1 phase, 0.5hp~5hp (0.4kw~3.7kw) 380~480v, 3 phase, 1hp~500 hp (0.75kw~375kw) Feature: Energy saving High torque Automatic voltage regulation User friendly Restart after instantaneous power interruption 9 levels for speed setting 6 digits display Programmable inputs and outputs Store and copy settings by using kp-201c digital keypad Rm5g series apply to the constant torque loaded;rm5p series apply to the variable torque loaded
Model No. : GNB 008-1 Specification: Dimension: 250(L) x 295(W) x 45(H) mm Fan Dimensions: 60 x 60 x 15 mm Fans Speed: 1500 R.P.M. í+ 10 % Fan Airflow: 30.5 CFM í+ 10 % Fan Noies Level: 26 dBA Bearing Type: Sleeve Rated Voltage: DC 5V All Crystal Design. Two Blue or Color Light Fans Directly Connect Power from USB Port of N/B
Models No. : GX-120NF Input Voltage: DC 12 V / 24 V Output Voltage: AC 100 ~ 115 / 220 ~ 230 V Continuous Power: 120 W Frequency: 50 / 60 Hz Low Battery-Voltage Alarm: 10.5 V í+ 0.5 V Low Battery-Voltage Shutdown: 10 V í+ 0.5 V Output Waveform: Analogue Sine Wave Efficiency: 85 ~ 90 % Cooling Fan: Yes Temperature Protect: 65 óXC í+ 5 óXC Protect Functions: Over load , Over heat , Low voltage Reverse connection , Short circuit Size: 65.5 x 129 mm Electrical Wire Extent: 0.8 m Weight: 370g Output Connection: Universal Outlets and USB Charge port Accessories: Portable flannel bag 1 PCS/Retail Box
Battery pack Li-ion 100pcs pre/carton 0.0444cbm pre/carton 5.0kg~18.3kg pre/carton
Expendable battery AA;AAA;D;C;VA9A;12V;NI-MAA(2000mAh);2CR5 100PCS/Carton 0.02371CBM 2000pcs/carton 0.0323CBM
AC/DC Switching Power Adaptors Input voltage:AC90-240V/47-63Hz Output voltage:DC3-24V/0.3-2.3A U.S European, U.K wall plug in type. With UL, CUL, CSA, TUV, CE, GS, PSE, approved For Chargers, PDA, MP3, Digital camera, Notebook, ADSL modem, MO-ROM, CD-ROM ,etc
AC/DC Switching Power Adaptors Input voltage:AC90-240V/47-63Hz Output voltage:DC3-24V/0.3-2.3A U.S European, U.K wall plug in type. With UL, CUL, CSA, TUV, CE, GS, PSE, approved For Chargers, PDA, MP3, Digital camera, Notebook, ADSL modem, MO-ROM, CD-ROM ,etc
