Tact Lever Switches is applied to low current circuit push switch for electronic equipment. Appearance of the Switch shall have good finishing, and no rust, crack or plating failures. Operating force of a static load shall be applied to the tip of actuator in operating direction. Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal in a desired direction for 1min. the test shall be done once per terminal.
Micro Switch action is PUSH-ON TYPE S.P.D.T Contact resistance measurements shall be made with a 1KHz ± 200Hz max DC 5V 1A contact resistance meter. Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute. The travel distance for the plunger to come to a stop shall be measured
Hook Switch is applied to low current circuit hook switch for electronic equipment. The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar. Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature. 45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure. Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment. Storage temperature range 96 hours maximum for continuous storage over a range The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switch MT 1101 V Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100V potential across terminals and frame for one minute.
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100 V Potential across terminals and frame for one minute
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment. Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Supplying many different types of string,draw cord for outdoor sportswear. Many sizes(outside dia meter) of Stretch and Non stretch, solid color or multi color mixed draw cord and Flat draw cord with tip for shoe and for other purpose.
1. Introduction Designed for coverage expansion of conventional macro cell base station for rural area with low popularity. To minimize the influence in ul path by higher power from dl, both paths are fully separated by electrical and mechanical. High-precision power control by zero error attenuator technology. Adaptive pwm fan control protects residents from loud noise. It has following key features : - supports 1.8ghz wcdma band, 3fa - gsm 900/1800/1900, cdma 800/1900, lte 900/1800 band also available - consists of two unit by dl and ul - dl : 50dbm, ul : 0dbm output - high input range : 30 ~ 46dbm - high precision output control by hybrid analog and digital attenuator - auto limit control , auto shut down, auto fan control - high ingress protection for harsh field environment
1. Introduction The LMPRF3030DS On-Frequency Repeater has been designed for indoor operation that is used to enhance 4G LTE signal strength in small and medium sized shadow areas such as building or a parking lot. 2. Key Performance and Features Supports 850MHz & 2.1GHz or 2.1GHz LTE Only GSM900/1800, CDMA 800/2100, LTE 1800/2100 Band also Available Consists of Two Unit by DL and ULSupports WCDMA Standards Easy Set Up by Auto Gain Control Function Auto Isolation Check between Donor & Remote Antenna Reverse Auto Sleep to Reduce BTS Noise Floor High Gain of 95dB Gain & 30dBm Output Single Housing for 2.1GHz and Extension Housing for 850MHz High Reliability & Quality proven by LG U+ Telecom in Korea Optional Remote Monitoring and Control via Wireless Data Modem 3. Application Medium Sized Office Buildings Shopping Center Parking Lot
CISCO IP Phone 7960G 31 units CISCO IP Phone 7962G 24 units Total 55 units @US$10 each FOB Korea
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate, by Improving the Electric Energy Environment. IRIS Power Saving Device ( 8 Models ) Due to constant exhaustion of the Energy Sources, it is necessary to Reduce Energy Consumption Rate by Improving the Electric Energy Environment. Combines State-of-the-Art Technology Carbon Nano Tube (CNT) an Excellent Effect in Noise Removal for inductive loads Three Phases Type : 6 Models
