Performs ultra-high efficiency Winglet shaped blades Innovative blade with Styrofoam material New technology to store and re-use wind Performs higher efficiency with extended blades From 3Kw to 15Kw Integrated with Solar Module as per requirement
Load power : 3kw Solar Module : Mono crystalline Installation : Ground or Rooftop Output wave : Pure sine wave Solar System Battery : Li-ion or Lead Acid 12V 200Ah X 2 On-grid : Option
Solar Panel Type: Mono crystalline Load Power : 1 MW Output Voltage : 120v/220v/380v Inverter : Pure Sine Wave Inverter Protection : Short Circuit, Over Load, Lightning Type : On-grid System AC ESS : Li-Ion Battery (Option) Monitoring : On-line Warranty : PV 25 Years
LED Solar Street Light, Built-in Intelligent MPPT charging controller with Bluetooth smartphone control, Microwave motion sensor with dimming circuit, Lithium-ion or Lithium_ion battery pack with smart BMS, Mono Crystalline Photovoltaic solar module
By using a brush that moves up and down, it removes the fine dust and dust that accumulates continuously, keeping the solar module clean at all times, maintaining the charging efficiency at the time of initial install. Depending on the saved program, the brush is operated four times a day to remove fine dust. The power produced by the high-efficiency solar panel is stored in a lithium-ion battery using an MPPT controller. The all-in-one lithium-ion battery has a long life and high charging and cooling efficiency compared to conventional lead-axis batteries. Led light sources with a light efficiency of 150 lumen/w are designed for maximum efficiency with low power.
LED Street Light, Built-in Intelligent MPPT charging controller, Microwave motion sensor with dimming circuit, Lithium-ion or LiFePO4 battery pack with BMS, Mono Crystalline Photovoltaic solar module , Wind turbine generator with vertical blade (Option)
N95 niosh, ff2, kf94 mask korea origin, covid 19 rapid test kit, solar streetlight, wind turbine, hybrid street light solar farm, electric leakage current prevention device, electromagnetic wave prevention device, other high technology electronic device.
"Luxfine LCP leakage current prevention device" is a power supply device that prevents leakage current, and electrical devices used by receiving power through this device are safe from leakage current. Leakage current is the current generated by an electrical device outside the normal track, i) the current flowing between the applied live line and the ground, ii) the current flowing between the live line and the neutral line (N), e.g., between the two terminals of the outlet. When a person encounters a conductor of an electrical device, the leakage current flows through the human body and poses a serious threat to the body and life. "Luxfine LCP" allows the human body to safely use electricity by preventing current from flowing even when it encounters the conductor of an electrical device. It allows safe use of electricity even in humid places or when flooded. Existing short circuit breakers are designed to protect the system by operating at leakage currents above 30mA, but the risk of electric shock is always present in sections below 30mA where the short circuit breakers operate normally. In other words, the current between 6 and 30mA also has a significant effect on the body's muscular control and nervous system, leading to secondary accidents or death. Leakage current causes failure, malfunction, life span reduction, fire, etc. of not only the human body but also the electrical equipment used. To prepare for electrical hazards that may occur in the event of a malfunction of a short circuit breaker or in a section below 30mA that is not protected by a short circuit breaker, equipment that can fundamentally block leakage current was developed. The current between the conductor and the ground of the electrical device using this equipment is almost "Zero" amperes. "Luxfine LCP" has built-in functions to drastically reduce the generation of electromagnetic waves that are fatal to the human body and to pre-detect the risk of fire due to aging power lines or de-insulation. In addition, to single-phase 220V, three-phase 380V, products ranging from 300VA to 10kVA are developed as standard models. Commercial and industrial applications with much larger capacity, as well as products with a step-down function of input 220VAC and output 110VAC can be also customized. Applications Places that require a lot of moisture and water, sewage treatment plants, water purification plants, fish farms The expensive old equipment that needs to be overhauled due to leakage current Streetlight pole, signal light pole in areas vulnerable to electric shock or habitually flooded
The electric shock hazard always exists at the section of below 30mA or 100mA where the leakage current breakers operate under normal conditions without any faults. It is believed that the current between 6 to 30mA is also dangerous because the sufferer loses muscular control, and it leads to a secondary accident. It will affect a serious problem of the nervous system also. To prepare for these electric shock risks originated from the malfunction of the equipment and the blow section of 30mA, we have developed the leakage current removal device. This is the world's first product that we can use electricity safely in humid workplaces or even in the water by preventing leakage currents so that we could touch the exposed conductors or case. Not only for the single-phase of 220VCA but the three-phases of 380VAC are developed from 300w to 10kVA, and Industrial application with even greater power consumption products and 110VAC input with 220VAC output products are customized.
Highly Efficient Products of 170lm/W (Separate Converter type) with elegant design. It looks great anywhere. (120~130lm/W Driverless type) With Max 20kV Power Surge protection device preventing the damage originated from the indirect surge and the inductive switching surge. Thermally stable aluminum stamping and diecasting structure and ultralight design to minimize the risk of falling loads. Adopting RF wireless dimming controller for remote on/off and the predetermined dimming with LTE communication (Option) By adopting the AC drive IC, a simplified and reliable circuit system has been ensured. (Driverless type) Not using the transformer and the electrolytic capacitors, the necessity of using the other components for modification of the PF, THD, and EMI has been fundamentally excluded. (Driverless type) With the perfect waterproof design and the AC drive IC, it can be applied for the refrigeration warehouse less than -30C as well as hazardous area lightings. (Option) By the internal PWM control, PIR sensing and dimming is also possible. (Option)
