Tape measure, pruning saw.
Measuring equipment for factory automation, temp. Controllers, counters, timers, limit switches, push button switches, relays, terminal blocks, sockets, magnetic contactors/switches.
.We provide 3d measuring service, however it should be paid.
Weight Measurement Function: By Hours, minutes and seconds unit, Display the status of the usage of liquid gas and it can be used being installed on storage tank or tank lorry and can be carried as a portable measuring instrument. PC Monitoring Function: As the remained liquid goes below 10% of its capacity, it automatically alarms to supplement liquid gas. Thus, the appropriate time for supplement of liquid gas can be decided on time. Alarm Function: the liquid remaining of the storage tank is less than 10%, The alarm sound provides information that you can setting the a liquid supply time. Diversity Of Power Supply: Use the usual 220volt electric, in case of power outage, the built-in battery will supply the charged electricity, in addition built-in battery is operated and available for tank lorry using the car battery. Option (Printer : additional purchase): Receipt Output Function; Portable thermal transfer printer can use the output value measuring of storage tank and tank lorry without visiting a long measuring place directly by the output as a receipt.
TECHNICAL DATA - Tensile Strength : 28 ~ 35 MPa - Elongation : 200 ~ 400% - Temperature : up to 500°F (260 C) - Hardness : R25 (Rockwell) Application - Control valves, Rod, piston FEATURES - Elimination of costly seal failure or blowouts - Reduced installation costs - Reduced equipment downtime with exact seal specifications - Reduced inventory costs - Lower friction / Friction a measurement of the resistance to sliding between a seal and hardware surfaces, is directly related to seal material coefficient of friction and the total load. - Longer Life / Individual sealing rings expand under bolt loading to maintain a tight, virtually leak proof set with up to 50% longer services over braided styles.
Detail Information Bilge alarm indicates an alarm signal when the concentration of drainage from Oily Water Separator/Filter Unit is higher or equal to 15ppm. As the solenoid valve will automatically shut off for 20 seconds after the response, so discharging process of bilge water could be operated without any attention of operator. Structure The bilge alarm case is constructed as a steel box in accordance with IP56 and sensing unit is sealed for water-proved. Electric parts and warning circuit are located in the main board. The front side of bilge alarm has digital ppm displayer and 2 LED (Normal : green, Alarm : red). Sensing unit and case is connected with flexible cable to avoid any damages. Principle of measurement The oil-contents in bilge water is measured by scattering action of the light induced by oil particles. By measuring scattering light and calculating the scattering rate, it factors in the influences of varying light sources. Scattering light can be detected by exposing the high intensity infrared rays to the sampling water passing through the cylindrical Sample -Tube(cell). =ª Specification Range : 0-25PPM Set Point : 15PPM Response Time : Within 20 Seconds(Adjust possible by user) Alarm Contacts/Rating : Single Pole c/o/2.5A at 250VAC Alarm Indication : Red LED on front panel Digital Display : 2digit 7-segment Output Signal : 0 ~ 5VDC, 4 ~ 20mA(option) Power / Consumption : 110/220VAC, 60Hz / 20VA Dimensions : Case:300mm(H) x 200 mm(W) x 120mm(D) Sensing Unit : 190mm(H) x 220mm(W) x 90mm(D) Enclosure Rating : IP56
Note ** Product Property - A precise thermometer controlling the temperature in accordance with a user's setting by detecting the precise temperature within by ±0.5 F error of measure measurement - It can be also used Temperature Controller when you put in heat pump under the main body - Product that is currently exported to American Aquarium company. - It can be used every countries handling sea water tank ** Precaution - When you use this, you have to connect a stabilizer. like earth leakage breaker - When blackout comes or installing product, you have to check set-up temperature - only for cooling, Operating time of compressor is about 3 minutes. Wait a minute please until it operates. - Main body of product should be installed at dry area - Main body of product should be avoided from water - Do not use close to magnetic field - LO on Display : Short at temperature sensor - Temperature is under 0 C - HI on Display : - Short at temperature sensor - Temperature is under 50 C Data - Length of Sensor : 4M - Usable Power : AC 220V / 60Hz , AC 110V / 50,60Hz - Range of temperature : 0C - 50C (Cooling ; 0 C - 20 C . Heating ; 14 C - 34 C) - Accuracy : Within ± 0.5C - Maximum Current Capacity : For Cooling : 20A. For Heating : 10A
NAME: High Density Polyethylene Material:reprocessed HDPE PELLETS RAW MATERIAL: 100% coated fabric Pellets from remanants APPLICATION: HDPE Pipe Grade HDPE pipe grade can be used in the production of pressure pipes, such as pressurized water pipes, fuel gas pipelines and other industrial pipes. It can also be used for making non-pressure pipes such as double-wall corrugated pipes, hollow-wall winding pipes, silicon-core pipes, agricultural irrigation pipes and aluminumplastics compound pipes. Density 0.987 Measure the Specific Gravity, according to ASTM D792 and Converted Melt Flow Index > 50 ASTM D1238
