Detail Information
Bilge alarm indicates an alarm signal when the concentration of drainage from Oily Water Separator/Filter Unit is higher or equal to 15ppm. As the solenoid valve will automatically shut off for 20 seconds after the response, so discharging process of bilge water could be operated without any attention of operator.
Structure
The bilge alarm case is constructed as a steel box in accordance with IP56 and sensing unit is sealed for water-proved. Electric parts and warning circuit are located in the main board. The front side of bilge alarm has digital ppm displayer and 2 LED (Normal : green, Alarm : red). Sensing unit and case is connected with flexible cable to avoid any damages.
Principle of measurement
The oil-contents in bilge water is measured by scattering action of the light induced by oil particles. By measuring scattering light and calculating the scattering rate, it factors in the influences of varying light sources. Scattering light can be detected by exposing the high intensity infrared rays to the sampling water passing through the cylindrical Sample -Tube(cell).
=ª Specification
Range : 0-25PPM
Set Point : 15PPM
Response Time : Within 20 Seconds(Adjust possible by user)
Alarm Contacts/Rating : Single Pole c/o/2.5A at 250VAC
Alarm Indication : Red LED on front panel
Digital Display : 2digit 7-segment
Output Signal : 0 ~ 5VDC, 4 ~ 20mA(option)
Power / Consumption : 110/220VAC, 60Hz / 20VA
Dimensions : Case:300mm(H) x 200 mm(W) x 120mm(D)
Sensing Unit : 190mm(H) x 220mm(W) x 90mm(D) Enclosure Rating : IP56
Measuring range: 0-30ppm Alarm 1: 1-15 ppm adjustable Alarm2: General alarm to control room Supply voltage: 110/220vac or 24vac Cleaning: Relay output for solenold valve sane as supply voltage Protection: IP65 Printour capacity: RS 232 adapter Overall dimensions: 210*200*100mm(L*W*D) Net weight: power module 1.2kg / measuring cell 1.1kg
BVZ, RWO, JOWA, POSEIDON WITH CAPACITIES OF 0.5 TO 10 TONS. 15 PPM BILGE ALARM MONITORS INCLUDE OPM 1, OCD 1M, OCD CM, OMD 11, OMD 21 & OMD 2005 & FOCAS 1500 A, B, C & FOCAS 1800.
15 ppm Bilge Alarm Monitor Type OCM-07 INTRODUCTION The OCM-07 type oil-in- water monitor has been designed specifically for use in continuous monitoring of oil-in-condensate or oil-in-boiler feed water without specific environment condition, it is applicable to high water temperature. The unit is supplied with 2 works-adjusted alarms. The set point (15mg/l) could be adjusted at any moment through the front panel. If an alarm set point is exceed, the alarms are visible at the front panel and the appropriate relays are switched. Features Compact and robust construction Low maintenance Small dimensions Easy installation Continuous on-line work Works adjustment Easy zero adjustment via push buttons (5mg/l)
Supplier: Lifeboat, liferafts, 15 PPM bilge alarm, oil water seperator, sewage treatment plant, fire fighting, SCBA
Supplier: Ship machinery & spares, marine main engines & spares, D.G. Set & spares, turbochargers & spares, oil purifier & spares, air compressor & spares, oily water separators and bilge alarm monitors, life saving appliances, navigation & marine electronics, pneumatic equipments, deck & engine stores, tanker specifics, hydraulic equipment
Content Monitor 15ppm Type OCM-09GB INTRODUCTION The OCM-09GB type oil-in- water monitor has been designed specifically for use in continuous monitoring of oil-in-condensate or oil-in-boiler feed water without specific environment condition, it is applicable to high water temperature. Features Compact and robust construction Low maintenance Small dimensions Easy installation Continuous on-line work Works adjustment Easy zero adjustment via push buttons (5mg/l) SPECIFICATION Type: OCM-09GB Range: 0 â??199mg/l Accuracy 0-50 mg/l Better than 2mg/l 50-199 mg/l Better than 5mg/l Linearity better than 2 % Display 3 digits 7 segment LED's Power Supply: 220VAC 24 Volt AC/DC ± 10% Consumption: 5 VA Alarm Points: Adjustable between 1- 199 mg/l Alarm Points works set: 10mg/l Alarm Indication: Red LED's Output Signal: 0 - 20 mA or 4 - 20 mA, reversible Ri < 500 â?¦ Sample Water Pressure: 0,1 - 8bar Sample Flow: approx. 0,5 - 4 l/min depend. to pressure Ambient Temperature: - 20 to + 55° C Sample Water Temperature: + 1 to + 80° C Size (over all): 394mmWÃ?280mmHÃ?135mD Degree of Protection: IP 65 Weight: 10 kg Pipe Connections: R 1/4" Female
Oil Contamination Monitor OCM- 15 The OCM-15 type bilge water alarm device has been designed specifically for use in continuous monitoring of oil-in-bilge water, 15 ppm alarm and control of discharge, detection, memory and enquiry of alarm status. It is applicable to detect boiler condensate water. And it applies to oil and chemical industries as well. Features Compact and robust construction Low maintenance Small dimensions Easy installation Continuous on-line work Works adjustment Easy zero adjustment via push buttons (+-5ppm) IMO-Resolution MEPC.107 (49). CCS approved
Applications: This device can be used to treat oil bilge water in order to make it reach the requirements of IMO.MEPC.107(49) resolution, which is also called 15ppm bilge separator. It contains type approved 15ppm bilge water separator, 15ppm bilge alarm and automatic shut down device. Features: ABS, CCS, BV, EC Approved England Mono Pump Germany Schneider Electric control box Germany DECKMA 15ppm bilge alarm Used for seaport, dock, industry, petroleum, various vessels
: HAMWORTHY, YANMAR, TANABE, ATLAS COPCO, DAIKIN, MITSUBISHI, SPERRE, HATLAPA ETC.
