Genuine auto parts.
Level control valve with high and low different level control.
Double extrusion structure with environment-friendly elastic material, grasp design for bass method.
Double extrusion structure with environment-friendly elastic material, grasp design for bass method.
Processing manufacture of faucet, gas and firefighting equipment, heavy equipment and machine, elbow for pipe connection, gasket, coupling, bolt, screw, flange, fitting, etc. 1:Elbow To switch directions of pipe 2:Reducer To reduce pipe sizes 3:Tee To divide one pipe to two or more pipes 4:Union To extend pipe 5:Cap To cover the end of pipe 6:Nut Manufacture of circular nut for faucets, common nut, cartridge nut, lock nut, and other nuts able to be processed on CNC or shelf
Model 137-010 consists of Robocon Valve (BALEM 130) and Two Flow Control Valve. This valve is installed at outline of pump to prevent back flow caused by Back Pressure. This valve is slowly opening to prevent sudden opening surges, When a pressure reversal occurs the higher downstream pressure is applied to the cover chamber through the control tube line, and the valve closes drip tight.
Capacity ------------------------------------ up to 4000 cmm Pressure ------------------------------------- up to 200 mmaq Inlet size --------------------------------- 300 up to 2000 mm Casing thickness -------------------------- 1, 5 up to 16 mm Impeller types ------------------ ac, as (adjustable pitch) Motor frame size ------------------------------- 63 up to 315 - electricity supply ; single or three-phase to suit a wide range of voltages and frequencies - motors maker ; korea & overseas ex e, ex d Drive type ----------------- coupling-, belt- or direct drive Casing form? combined casing, swing out shot casing Surface treatment --- primer, finish, hot-dip galvanized Material -impeller --------- cast aluminium, engineering plastic -casing -------------- steel , aluminium, stainlesssteel Thermal & ip protection
Model 138-010 consists of Robocon Valve (BALEM130) and Solenoid On-Off Pilot Valve. It opens or closes upon receiving an electrical signal to the solenoid pilot control. This valve, as a solenoid pilot valve, can be provided two different types. The standard basic valve which normally closed (basic valve opens as solenoid operates), and valve made to order which normally opened (Basic valve closes as solenoid operates). Optional control features are available, such as timer, relay, probe, etc for remote control by electrical signal depends on user's site conditions.
* Ultra Thin Filter and High-Tech Fabric Face Mask (Stay Cooler in Summer Season) * Brand Name: BoBo Face Mask * Cool Mask, Summer Mask, Thinner Mask, Highly Breathable Mask, High-Tech Fabric Mask, Filtering Mask, Sun Protective Mask, Less Skin problems Mask, Water-Resistance Mask, Reusable Mask * Feature A. Cool Fabric Face Mask in Summer season B. Anti-Bacterial Effect: 99 % C. Water resistance: Water did not permeated D. Quick Dry cooling prevents facial skin problems E. Sun Protection, deodorizing effect (Outdoor activities) F. High Performance Fiber performs 98 % of dust collection fiber G. Certified to filter out at least 80% of the pollutant H. With the Thickness of 0.06 mm, it maximize air ventilation I. 99.9% of performance maintenance after 70 times washing * Length: Large size - 180 x 135 (mm), Medium size - 150 x 110 (mm), vertical*horizontal * Material: PP non-woven fabric, antimicrobial deodorant high density fiber * Size: Large, Medium (Including two Strap Length Adjusting Clip) * Country of Origin: Republic of Korea * Color: Black & White * Payment: T/T or L/C * Lead Time: Within 7 Days after Purchase Order or payment * INCOTERMS 2020 FOB BUSAN (South Korea)
Describe the idea and what it actually does: The role of the shaft accounts for about 70% of the performance of a golf club, and the weight, strength, torque and kick point of the shaft vary according to the type and intended use of the golf club. To solve problems afflicting a general cylindrical shaft and improve the performance thereof, the present shaft has been developed to have a composite design system. That is, to improve the distance and direction by evaluating the roles of various parts of the shaft, fabric having strength and weight appropriate to the functions of respective parts of the shaft is selected and molded with connecting parts thereof overlapping each other according to the process. At this time, joints are formed on the outer circumference according to the number of parts connecting the fabric. The joint of the present shaft is formed to have a structure similar to that of bamboo. Further, the shaft specifications, according to which the number of joints and spaces therebetween differ, is decided according to a golferí»s ability and tendencies. Thus, when the golfer swings the golf club, each joint performs a function similar to that of an artificial joint. As a result, the head speed achieved by the golfer is increased; the distance is increased by about 20-30 yards by the stabilization of impact (head spot); and the direction is improved by controllingthe torsion of the joint located in the middle of the shaft in the case of an impact. 2. Explain in detail how the idea would be operated used The inner layer of the shaft is formed of a reinforcement, folded in a single fold or two or more folds,that determines the flex and weight of the shaft so that the direction of the texture of the material repeats in an X arrangement. The middle layer is formed on the outer circumferential surface of the inner layer. To form the first middle layer, 5 divided middle layers are arranged and folded along the axial direction of the shaft so that 4 overlapping joints are formed. A second middle layer is also formed in the same manner as the first middle layer. The outer layer is formed to have a straight angle and be parallel to the axial direction of the shaft on the outer circumferentialsurface of the middle layer and is formed of one cut piece of material folded once, or twice or more, having appropriate strength, elasticity and tensile elastic modulus so that the overlapping joints of the middle layers are not separated by the impact of a swing, and are durable. Then, the shaft is finished by heat-treating it after rolling heat-shrink tape on the outer circumferential surface of the outer layer, 3. What features do you believe your idea has that makes it unique and appealing? The shaft is manufactured by folding a plurality of divided middle layers, which are different from each other with respect to strength, elasticity and tensile elastic modulus. Meanwhile, when the following factors are considered in combination with each other, it is possible to manufacture a shaft having various characteristics. 1) Number of Joints for Each Shaft - In the case where the number of joints is large, a sensation of impact is increased somewhat. - The case where the number of joints is small is appropriate for golfers with weak swings. - In the case wherethe number of joints is large, the directionality becomes very good and the feeling of impact is close to that of a steel shaft.- In the case where the number of joints is small, the trajectory becomes high. 2) Space between Joints - Even though the number of joints is the same, a soft feeling is provided to users in the case where the space between the joints in the tip part is long. -The kick point goes down toward the tip when the space between the joints in the butt part is long. - A high kick is appropriate for users in the intermediate class or above, and generates a low trajectory, and the rolling distance of the golf ball is increased. 3) Structure of Fabric - Fabric having high elasticity and strength is used, thereby resulting in distinctive performance 4.What need does the idea fulfill? This product has been manufactured and sold in Korea, and it is necessary to expose this product to U.S. consumers for access to the U.S. market. Meanwhile, this product acquired certification according to the USGA standard in the U.S.A. and the R&A standard in the United Kingdom. 5. Descripbe possible variations of your idea: The middle layers may be manufactured after the divided middle layers are cut at an incline rather than at a straight angle, and the durability can be improved by setting the cut inclinations of the first middle layer and the second middle layer in opposite directions relative to each other.
Golf shaft The role of the shaft accounts for about 70% of the performance of a golf club, and the weight, strength, torque and kick point of the shaft vary according to the type and intended use of the golf club. To solve problems afflicting a general cylindrical shaft and improve the performance thereof, the present shaft has been developed to have a composite design system. That is, to improve the distance and direction by evaluating the roles of various parts of the shaft, fabric having strength and weight appropriate to the functions of respective parts of the shaft is selected and molded with connecting parts thereof overlapping each other according to the process. At this time, joints are formed on the outer circumference according to the number of parts connecting the fabric. The joint of the present shaft is formed to have a structure similar to that of bamboo. Further, the shaft specifications, according to which the number of joints and spaces therebetween differ, is decided according to a golferí»s ability and tendencies. Thus, when the golfer swings the golf club, each joint performs a function similar to that of an artificial joint. As a result, the head speed achieved by the golfer is increased; the distance is increased by about 20-30 yards by the stabilization of impact (head spot); and the direction is improved by controllingthe torsion of the joint located in the middle of the shaft in the case of an impact. 2. Explain in detail how the idea would be operated used The inner layer of the shaft is formed of a reinforcement, folded in a single fold or two or more folds,that determines the flex and weight of the shaft so that the direction of the texture of the material repeats in an X arrangement. The middle layer is formed on the outer circumferential surface of the inner layer. To form the first middle layer, 5 divided middle layers are arranged and folded along the axial direction of the shaft so that 4 overlapping joints are formed. A second middle layer is also formed in the same manner as the first middle layer. The outer layer is formed to have a straight angle and be parallel to the axial direction of the shaft on the outer circumferentialsurface of the middle layer and is formed of one cut piece of material folded once, or twice or more, having appropriate strength, elasticity and tensile elastic modulus so that the overlapping joints of the middle layers are not separated by the impact of a swing, and are durable. Then, the shaft is finished by heat-treating it after rolling heat-shrink tape on the outer circumferential surface of the outer layer, 3. What features do you believe your idea has that makes it unique and appealing? The shaft is manufactured by folding a plurality of divided middle layers, which are different from each other with respect to strength, elasticity and tensile elastic modulus. Meanwhile, when the following factors are considered in combination with each other, it is possible to manufacture a shaft having various characteristics. 1) Number of Joints for Each Shaft - In the case where the number of joints is large, a sensation of impact is increased somewhat. - The case where the number of joints is small is appropriate for golfers with weak swings. - In the case wherethe number of joints is large, the directionality becomes very good and the feeling of impact is close to that of a steel shaft.- In the case where the number of joints is small, the trajectory becomes high. 2) Space between Joints - Even though the number of joints is the same, a soft feeling is provided to users in the case where the space between the joints in the tip part is long. -The kick point goes down toward the tip when the space between the joints in the butt part is long. - A high kick is appropriate for users in the intermediate class or above, and generates a low trajectory, and the rolling distance of the golf ball is increased. 3) Structure of Fabric - Fabric having high elasticity and strength is used, thereby resulting in distinctive performance 4.What need does the idea fulfill? This product has been manufactured and sold in Korea, and it is necessary to expose this product to U.S. consumers for access to the U.S. market. Meanwhile, this product acquired certification according to the USGA standard in the U.S.A. and the R&A standard in the United Kingdom. 5. Descripbe possible variations of your idea: The middle layers may be manufactured after the divided middle layers are cut at an incline rather than at a straight angle, and the durability can be improved by setting the cut inclinations of the first middle layer and the second middle layer in opposite directions relative to each other.
High quality 4 Layer filters including high efficiency Melt-Blown filter. The three-dimensional structure perfectly covers the mouth and nose, makes it easy to breathe, and frees up enough space to speak. Approved FDA,CE certification. The lowest Price and High quality than similar production like N95,KN95
