Addition cure Electronic Potting Silicone Rubber 1. Product Feature of Addition cure Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)ã?�PPã?�ABSã?�PVC, etc. and metal materials. 2. Typical Application of Addition cure Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Addition cure Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. 4.Notes of Addition cure Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance. PACKAGE 40Kg/pail as a set (Part A 20Kg + Part B 20Kg) SHELF LIFE AND TRANSPORTATION 1. Twelve(12) months when stored at 24C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals. 3. Storage beyond the expired date doesnot necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons. -
Platinum Cure Silicone Foamsfor filling Description of Platinum Cure Silicone Foams for filling Platinum Cure Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. HY-F663 Platinum Silicone Foams expands 3.5 times its original volume and develops a uniform 20 lb./cu. ft. cell structure (320 kg/m3). Vibrant colors can be achieved by adding Silc-Pigsilicone color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation. Typical Applications for Platinum Cure Silicone Foams for filling Platinum cure Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening. Technical Parameters Product HY-F663 Appearance white Mix ratio(A:B) 1:1/10:1 Mixed Viscocity ï¼?mPa.sï¼? 15000±2000 Pot life/working time (mins) 5-8 Curing time/setting time (mins) 40 Shrinkage rate ï¼?%ï¼? 0.1 Approx. volumetric expansion 3.5 times Lbs./Cu. Foot=Kgs./Cu.meter 20 lb/ft3 = 320 kg/m3 PROCESSING RECOMMENDATIONS of Platinum Cure Silicone Foams for filling silicone products Store and use at room temperature (73°F/23°C). These products have a limited shelf life and should be used as soon as possible. Good room size ventilation is essential. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Cure Inhibition - Addition cured silicones may be inhibited by certain contaminants such as sulfur, polyesters,certain wood surfaces, epoxies, urethane rubber and tin catalyzed silicones resulting in tackiness at the pattern interface or a total lack of cure throughout the mold. If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of foam onto a non-critical area of the pattern.Inhibition has occurred if the matrerial is gummy or uncured after the recommended cure time has passed. This product will not cure against tin-based silicone rubbers. Applying A Release Agent - Silicone Foams will stick to some surfaces and a release agent may be necessary to facilitate demolding. When casting Silicone Foams into or over other platinum silicones, apply Ease Release 200 prior to applying foam. SHELF LIFE: 8-10 months when stored under 24â?? in original unopened packages. PACKAGE: Packed in 20kg/pail + 20kg/pail and 200kg/pail + 200kg/pail. -
Quick Details Table Decoration & Accessories Type: Mats & Pads Material: Silicone Feature: Eco-Friendly Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: felt glass coaster Item: felt glass coaster Color: any color in pantone Packaging: poly bag or customized Logo: customized MOQ: 1000 pcs Certification: FDA LFGB Sample: available weight: 15g size: Dia80mm material: silicone
Quick Details Use: Credit Card Material: PVC Brand Name: lifetop Model Number: card holder rfid Item: card holder rfid Color: any color in pantone Packaging: poly bag or customized Logo: customized MOQ: 500 pcs Certification: FDA LFGB Sample: available weight: 30g size: 95*58*6mm material: silicone
Quick Details Type: Baking & Pastry Tools Baking & Pastry Tools Type: Baking & Pastry Spatulas Material: Metal Certification: FDA, LFGB, FDA LFGB Feature: Eco-Friendly Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: icing spatula Item: icing spatula Color: dark red and silver Packaging: poly bag Logo: customized MOQ: 100sets Sample: available weight: 18g,58g,61g,91g size: 4inch,6inch,8inch,10inch material: wood and stainless steel
Quick Details Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: Exercise Hand-muscle Developer Item: Exercise Hand-muscle Developer Color: yellow,blue,geen,orange Packaging: poly bag or customized Logo: customized MOQ: 500 pcs Certification: FDA LFGB Sample: available weight: L:97G, S:45G,mini:40g color-poundage: yellow-40LB,blue-50LB,green-60LB,orange-70LB Material: silicone Item Name Personalized Heat Resistant Anti-slip silicone felt glass coaster Material 100%food grade silicone Color any color in pantone Feature 1.Eco-friendly,harmless,non-toxic 2.Working temperature:-40-230 C 3.Easy to clean and suitable to use 4.Logo can be printed,embossed,debossed MOQ1000 pcs Package 1.Inner packaging:1pc/opp bag 2.Outer packaging:carton Custom package acceptable CertificateFDA;LFGB;ROHS, Payment\T/T;L/C;Western Union Delivery15 to 20 days
Quick Details Type: Baking & Pastry Tools Baking & Pastry Tools Type: Baking & Pastry Spatulas Material: Metal Certification: FDA, LFGB, FDA LFGB Feature: Eco-Friendly Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: icing spatula Item: icing spatula Color: dark red and silver Packaging: poly bag Logo: customized MOQ: 100sets Sample: available weight: 18g,58g,61g,91g size: 4inch,6inch,8inch,10inch material: wood and stainless steel
Ferro Silicon is a universal heatblocker used to produce carbon and stainless steel This additive is used with other ferro alloys in the deoxidising process of steel and in the production of silicon itself It is also used in the production of cast iron as it can accelerate graphitisation Ferro Silicon replaces the need for ferro manganese spiegeleisen and calcium silicides in the manufacturing process
Introduction Our electronic-grade silicon Sol is a high-purity solution specifically developed for the demands of the electronics industry. Engineered to meet strict purity standards, this silicon sol is ideal for use in sensitive electronic applications, including integrated circuits, precision polishing, and high-purity coatings. Product Specifications Our electronic-grade silicon Sol is formulated with rigorous standards, making it an ideal choice for sensitive electronic applications. Key specifications include: Purity Level: Ultra-high purity at 99.99%, reducing impurities to ensure contamination-free application, critical for semiconductor manufacturing and integrated circuits. Particle Size: Uniform particle size averaging 20-30 nanometers, optimized for even application and superior polishing in high-precision processes. Concentration Range: Available in 20% and 30% silicon dioxide concentrations, catering to varying manufacturing needs for different coating and polishing requirements. pH Stability: Engineered with a stable pH (7�±0.5), maintaining chemical balance during application to prevent material degradation and ensure consistency across production batches. Storage and Shelf Life: With an extended shelf life of up to 12 months under standard conditions, ensuring long-term quality and usability in manufacturing environments. Application Scenarios Electronic Grade Silicon Sol is primarily used in: Integrated Circuit Manufacturing: Essential for wafer and circuit board polishing, improving surface uniformity and quality. High-Purity Coatings: Provides a smooth, contamination-free layer on electronic components, enhancing durability and function. Precision Polishing: Suitable for fine polishing of delicate electronic parts, reducing defects and maintaining high performance in final products. Product Advantages Purity and Quality Assurance: Consistent ultra-high purity ensures reliable performance in critical electronics applications. Enhanced Precision: Fine particle size and stable concentration make it perfect for high-precision tasks, reducing defects and material loss. Customization: Available in custom concentrations and grades to meet specific needs in electronics manufacturing.
Food Grade Silicone Rubber Food safe silicone rubber material is a kind of inorganic polymer colloidal material formed by the condensation of silicic acid, which is a kind of environmental protection silica gel. In the normal state, it does not react with other acids and alkalis except caustic soda and hydrofluoric acid. And it belongs to a colloidal structure, so it has many micropores and a large specific surface area. Food-grade silica gel is mainly used in food-related appliances, which is different from solid glue and liquid glue. Solid food silica gel is a kind of translucent silicone rubber, which uses platinum-rhodium complex as a curing agent, and is suitable for the processing and production of food-grade molded products, such as china silicone spatulas and electric rice cookers; liquid food silica gel is a two-component, translucent addition liquid silicone rubber material, which has superior mechanical properties and is especially suitable for food silicone rubber products, such as baby pacifiers and bottles. Types of Silicone Rubber Food Safe Food Grade Liquid Silicone Rubber For Baby Nipple/Bottles Food Grade One Component Solid Silicone Food Grade Two-component Low Temperature Curing Solid Silicone For Kitchenware What is the difference between silicone and food grade silicone? Silicone is a synthetic material made from silica, and is widely used in many industries such as healthcare, automotive, and industrial. Silicone is also used in many consumer products such as cookware, bakeware, and children's toys. It's important to understand the differences between silicone and food grade silicone when purchasing items for use in food preparation and storage. Food grade silicone is a specific type of silicone that has been approved for use in contact with food. It is made from a special type of silicone that does not release toxic chemicals into food when it is heated or in contact with acidic or alkaline ingredients. Food grade silicone is also non-porous and will not absorb odors or flavors from food. This makes it an ideal material for creating food storage containers, bakeware, and other items that come into contact with food. The biggest difference between regular silicone and food grade silicone is the purity of the material. Food grade silicone is made with a higher level of purity than regular silicone, which helps to reduce the risk of contamination. Additionally, this silicone rubber wholesale is designed to withstand higher temperatures than regular silicone and can be used in the oven and microwave.
Silicone Flame Retardant The product is a heat-resistant peroxide-curing solid silicone rubber compound for forming. Our flame resistant silicone is a high-quality product designed to meet the rigorous requirements of a wide range of industries. This product is ideal for applications that require superior fire resistance and superior physical properties. Its superior flame retardancy is obtained from a combination of flame retardant additives and our unique compounding processes. The product provides excellent physical properties such as tensile strength, elongation, tear resistance, and compression set resistance. Our flame retardant solid silicone is suitable for a wide variety of applications such as automotive, electrical, industrial, and medical applications. Betely, a sophisticated flame retardant silicone rubber factory, is confident that our flame retardant solid silicone can meet your needs and exceed your expectations. We invite you to explore our product category further and contact us with any questions. Types of Flame Retardant Solid Silicone Flame Retardant Solid Silicone Rubber SH-8660 Is silicone flame resistant? Silicone is a popular material that is used in many everyday items and products. It is renowned for its versatility, as it can be used to construct items ranging from cooking utensils to medical equipment. As such, it is important to understand the characteristics of silicone and its potential uses. One important aspect of silicone is its flame resistance. In order to understand if silicone is flame resistant, it is important to look at its properties and how it responds when exposed to flames.
Embossing Silicone Rubber For Fabric/Garment/Textile The silicone ink embossing is a two-component, semi-transparent addition liquid silicone rubber system. The material has excellent vulcanization. It is especially suitable for cloth logos which need excellent 3D effect. Product Features Of Embossing Silicone Ink Rubber For Fabric/Garment/Textile Fast curing speed Strong adhesion Good fluidity Good bubble removing property Easy to dye Poisonless and tasteless Good heat and weather resistance Application Field Of Embossing Silicone Rubber For Fabric/Garment/Textile Clothing labels, Silicone decorations/crafts, logo scutcheon, and accessories. The Performance Parameters Of Embossing Silicone Rubber For Fabric/Garment/Textile Properties BQ-1070-1A/B Appearance Semi-transparent Viscosity (pa.s) A: 13 million mPa.s B: 500-2000 mPa.s Density (g/cm3) 1.10-1.13 Hardness (Shore A) 57-62 Tensile strength (MPa) 6 Elongation (%) 300% Tear strength (kN/m) 25 As a silicone factory china, we will do our best to meet all the needs of customers.
Silicone Fluid/Silicone Oil Bulk Silicon Fluids are a type of synthetic lubricant made from polydimethylsiloxane (PDMS) and other silicone-based compounds. They are designed to provide superior lubrication, thermal stability, and protection against corrosion and wear due to their low surface tension and high viscosity. Silicon Fluids are often used in the automotive and aerospace industries, as well as in medical devices, because they can withstand extreme temperatures and pressures, and they are non-toxic and non-flammable. Additionally, they provide excellent lubricity and wetting, making them ideal for use in a variety of applications. Types of Silicone Oil/Silicone Fluid for Sale Vinyl Silicone Oil Hydrogen Silicone Oil Hydroxyl Silicone Oil Polydimethylsiloxane (PDMS) Polydimethylsiloxane [(trimethoxysilyl)oxy]-terminated CAS NO.: 142982-20-5 Uses of Medical Silicone Oil/Silicone Fluid BTL silicone fluids are a range of specialty fluids that provide a wide variety of benefits to industrial and consumer applications. These fluids are composed of polydimethylsiloxane, a synthetic form of silicone that is known for its low volatility, low toxicity, and high thermal stability. BTL china silicone fluids including methyl hydrogen silicone oil and hydroxyl silicone oil can be used in a variety of applications, from lubrication to insulation. They are often used as lubricants in machinery and equipment in order to reduce friction and wear. They can also be used as a dielectric medium in electrical and electronic components, providing insulation and preventing electrical shock. In the medical sector, BTL silicone fluids are often used as a carrier for medications and medical ointments. They are also used as a therapeutic aid in the treatment of chronic wounds and burns. BTL silicone fluids can also be used in the food and beverage industry, where they are used as defoamers in beer and soft drink production. They are also used to coat paper and cardboard products, providing water repellency and preventing spoilage.
Silicone FDA Soft Touch Coating Silicone soft touch coating is made from special silicone oil, silicone resin, special powder and environment-friendly odorless solvent. It adopts advanced technology to be a two or multi-components protective coating with smooth, anti-static effect and section sensitivity. Product Features Of Silicone FDA Soft Touch Coating Smooth and fine hand feeling fine appearance Excellent adhesion, it has excellent adhesion on 0-80�° silicone Stain resistance Resistance to various kinds of strong acids and alkalis and other chemicals Excellent rubber resistance and alcohol resistance FDA qualified, no smell after spraying with the FDA soft-touch coating Application Field Of Silicone FDA Soft Touch Coating Soft touch silicone coating has passed Biocompatibility and FDA test. The silicone FDA soft-touch coating is suitable for baby bottles, tableware, and other products which closed contact human body. The function of the silicone FDA soft-touch coating is protection, decoration, soft touch feeling, etc. It can also improve the additional value. Process Condition Of China Silicone FDA Soft Touch Coating Temperature Time High temperature (180-220â??) 6-10min Middle-low temperature (20-30â??) 20-30min Low temperature (90-100) 30-60 min Representative Models Of Silicone FDA Soft Touch Coating Good applicability models: HSL-F0601, HSL-F0605A/B
This series is made of silver&carbon powder, resin, additives, and solvents with excellent conductivity, and has excellent conductivity. It has excellent adhesion on pet, PI, TPU, and other materials. BTL conductive paste is a kind of paste with certain conductivity after curing or drying. It can connect a variety of conductive materials together so that the connected materials form an electrical path. In the electronic industry, BTL conductive paste has become an indispensable new material. There are many kinds of conductive pastes, which can be divided into general conductive pastes and special conductive pastes from the perspective of application.
Silicon metal 97 is a type of silicon metal alloy that is composed of approximately 97% silicon, with small amounts of iron, aluminum, and other trace elements. Silicon metal 97 is often used in industries where lower purity silicon is acceptable, such as the production of silicones, silanes, and other chemicals. It may also be used as a deoxidizing agent in the steel making industry or as an additive in the aluminum industry.
Silicon metal 553 is a high-grade silicon metal alloy that is commonly used in the production of aluminum-silicon alloys, which are widely used in the automotive industry for engine blocks, cylinder heads, and other parts. It is also used in the production of silicones and other specialty chemicals, as well as in the production of high-tech products such as semiconductors and solar panels.
Using high-purity silicon carbide powder, formed through isostatic pressing, fired to create high-density structural components. Long lifespan, good heat dissipation performance, low friction coefficient, enhancing grinding efficiency. Lightweight, minimal centrifugal force, high grinding speed, no pollution, high product purity, improving grinding efficiency, saving costs. We adopt isostatic pressing forming method. The outer diameter of silicon carbide wear-resistant barrels can reach up to 1000mm. Large-diameter silicon carbide barrels are formed by reaction sintering, while small-diameter barrels are formed by pressureless sintering, which is more wear-resistant than reaction sintering.
Silicon Ore is an ore that drops Raw Silicon which can be used in the Circuit Fabricator to craft Basic Wafers, Advanced Wafers, or Blue Solar Wafers. It can be destroyed using any type of pickaxe, but it will only drop Raw Silicon if you use an Iron Pickaxe, Heavy Duty Pickaxe, Diamond Pickaxe, or Desh Pickaxe.
Product Description Food grade liquid silicone is used to .candy, cake and cholocate and soap mold and making artificial stone,cement and gypsum. Food grade quality silicone with nontoxic,Excellent fluidity, high tear and tensile strength, High duplication times repeated use, easy to demould,High temperature resistance and cure can be accelerated by heat Model 6210 6215 6220 6225 6230 Mixing ratio (A:B) 1:1 1:1 1:1 1:1 1:1 Hardness (Shore A)â?¥ 10 15 20 25 30 Tear-strength (kgf/c m�²)â?¥ 16 18 20 21 22 Viscosity (A/B mixed 25�°C mpa.S) 8000�±2000 8000�±2000 10000�±2000 10000�±2000 10000�±2000 Shrinkagerate (%)â?¤ 0.1 0.1 0.2 0.1 0.1 Elongation(%) 500 480 450 450 400 How to use: 1.A and B must be mixed evenly into a clean plastic or metal container, The bottom and walls of the container must be scraped well to ensure that the silicone is mixed with the curing agent. 2.The pre-operation time of the mixed is 30-40 minutes at room temperature, and the product prototype is poured by vacuum defrosting.The product can be cured completely at room temperature of 3-4 hours and heated at 80-120�ºC for 30 minutes. 3. When pouring or brushing mold for medium or large products, it is recommended to pour or brush 2-3mm thick silica gel on the surface of the product to fully and completely contact with the prototype. Package: 10KG, 20KG, 200KG or according to customer requirements.
