LCG is a kind of thermal interface material which coating thermal conductive polymer on a layer of fiberglass. The stickiness of the material is slightly weakness for easy procession. And insulation and tear resistance are also better. Its stickiness and flexibility, even in extremely rough and very uneven surface, also can bring a good thermal filling effect. Features & Benefits: Fiberglass substrate, anti-puncture, shear and tear resistance Only the bottom with a sticky, slightly faint on the front, easy to install High-load, low-hardness gap filling material Strong electrical insulation Typical Applications: AC / DC power supply Car equipment / charger Between the motherboard and the chassis Drive control any heating element Uninterruptible power supply (UPS) Power semiconductor-TO packaging products
Floating pneumatic rubber fenders have been in use for around 50 years. It is the leading device for marine application in the world. This compressed air filled rubber fender is used as a protective medium for ship-to-ship operation(STS), ship-to-quay(STQ) and ship-to-berthing(STB). Florescence Pneumatic Rubber Fender Construction: Outer rubber: rubber layer that covers the outside of the fender to protect the cord layers and the inner liner rubber from abrasion and other external forces. Inner rubber: liner of a rubber membrane that seals the pressurized air inside the fender. Synthetic-tyre-cord layer for reinforcement: layer made of synthetic-tyre-cord fabric, which maintains the internal air pressure of the fender. Bead ring: steel ring which is placed at one end (or both ends) of the fender and holds the end of cord layers Flange opening: steel flange, which is mounted on the fender, to which an air valve or safety valve can be adapted. Florescence Pneumatic Rubber Fender Advantages: 1. High energy absorption and with a low reaction force 2. Light weight, portable and floatable, can be installed and replaced easily 3. Heavy duty and long service life-over 10 years 4. Supplied as sling type (body only) or with chain and tire net for protection of the fender body 5. Sizes from 0.5m diameter Ã? 1.0m length up to 4.5m diameter Ã? 12m length 6. Suitable for locations with large and small tidal differences Classification of floating pneumatic fender: Fender types: 1.Net-type fender: fenders which are covered by a tire chain net, each end shall be linked together with one to two ring(s). 2.Sling-type fender: fenders which are designed to be used without a protection net. Initial internal pressure: 1.Pneumatic fender 50 (initial internal pressure 50 KPa) 2.Pneumatic fender 80 (initial internal pressure 80 KPa)
Floating pneumatic rubber fenders have been in use for around 50 years. It is the leading device for marine application in the world. This compressed air filled rubber fender is used as a protective medium for ship-to-ship operation(STS), ship-to-quay(STQ) and ship-to-berthing(STB). Florescence Pneumatic Rubber Fender Construction: Outer rubber: rubber layer that covers the outside of the fender to protect the cord layers and the inner liner rubber from abrasion and other external forces. Inner rubber: liner of a rubber membrane that seals the pressurized air inside the fender. Synthetic-tyre-cord layer for reinforcement: layer made of synthetic-tyre-cord fabric, which maintains the internal air pressure of the fender. Bead ring: steel ring which is placed at one end (or both ends) of the fender and holds the end of cord layers Flange opening: steel flange, which is mounted on the fender, to which an air valve or safety valve can be adapted. Florescence Pneumatic Rubber Fender Advantages: 1. High energy absorption and with a low reaction force 2. Light weight, portable and floatable, can be installed and replaced easily 3. Heavy duty and long service life-over 10 years 4. Supplied as sling type (body only) or with chain and tire net for protection of the fender body 5. Sizes from 0.5m diameter Ã? 1.0m length up to 4.5m diameter Ã? 12m length 6. Suitable for locations with large and small tidal differences Classification of floating pneumatic fender: Fender types: 1.Net-type fender: fenders which are covered by a tire chain net, each end shall be linked together with one to two ring(s). 2.Sling-type fender: fenders which are designed to be used without a protection net. Initial internal pressure: 1.Pneumatic fender 50 (initial internal pressure 50 KPa) 2.Pneumatic fender 80 (initial internal pressure 80 KPa)
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
Pourable, addition-curing, two-component silicone rubber that vulcanizes at room temperature. Non-toxic, odorless, two-component liquid silicone rubber, are two-component materials.Resistance high temperature of 250, shrinkage rate lower than 0.1%.
Applications of liquid pad printing silicone rubber Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface. Features of liquid pad printing silicone rubber a. resistance to deformation, high-temperature b. high printing times c. good aging resistance d. exceptional elasticity e. great printing effect
HAIR RUBBER BAND
ZIG ZAG HAIR RUBBER BAND
30 PCS BOX WOMENS RUBBER HAIR BAND IN MANY MULTI COLORS
Rubber band from vietnam good quality
DESCRIPTION: Commercial rubber sheet used for gasket & packing purpose in industrial applications. These sheets / rolls are made from Prime polymer blended with reclaim rubber. As it is cured using compression moulding & rotary drum curing system available in smooth & cloth impression finish with or without choice of insertion. APPLICATIONS: This commercial rubber sheets / rolls are mainly used for flange gasket packing to avoid leakages from air, water & inorganic chemicals, machinery packing pads, anti vibration pads & flooring purpose. PROPERTY: Good resistance to inorganic chemicals, water, air & heat up to 70°C. Poor resistance to Ozone, UV, Sunlight, oil & solvents & organic chemicals. Boron Rubbers India has custom designed this rubber to meet many applications on several different levels while maintaining a very economical basis for a rubber sheets / rolls. COLOR: Black No GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Elongation (%) 1 BRZ – 1560 1.50 70 25 200 2 BRZ – 1665 1.60 65 20 175 3 BRZ – 1870 1.80 60 15 150 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 STORAGE OF PRODUCTS Do not expose rubber sheet to direct sunlight, sheets away from heat source, preferably in dark, air ventilated room will help give longer life & optimum properties Do not remove polythene packing before use to prevent it from exposure of atmospheric oxygen, ozone & polluted air. Do not store rubber sheet rolls in open, even after covering it with tarpaulin to protect from air & rain. Always keep rolls in vertical position ONLY Keep rolls away from solvent, oil & fuel storage. Do not use hooks while loading/unloading the rolls. Inspect sheet for smooth surface & hardness (with rubber hardness tester).
DESCRIPTION: NR / SBR blend rubber sheets / rolls are used in the commercial and industrial applications. This specifically designed rubber material is long-¬lasting that is suitable for operational use which provides excellent mechanical properties like high resilience, low compression set, high resistance to cut, tear & abrasion & also offers resistance to many acids, alkalis & salts. The operation temperature range is (-¬20°C to +80°C). It is available in wide range of hardness from 40 Shore A to 80 Shore A. It has very good physical properties like Tensile strength, wear & tears properties, Abrasion resistance. APPLICATIONS: NR / SBR Rubber sheets / rolls are used for wide range of applications like skirt board, bridge bearing, gasket for high pressure packing, heavy weight machinery packing, Para-¬quality for sand/shot blasting machinery & used as shock absorber. NR / SBR Rubber sheets/rolls can be used as shelf liner; workstation table liner and work area rubber lining that can with and moderate chemicals & alkaline solutions. These sheets can also be used for anti-abrasion lining for material handling machinery in mines alike industries PROPERTY: Excellent resistance to inorganic chemicals, water, air & heat up to 80°C. Poor resistance to Ozone, UV, Sunlight, oil & solvents & organic chemicals. NO. GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Elongation (%) 1 BNS-1240 1.20 40 80 600 2 BNS-1345 1.30 45 90 500 3 BNS-1450 1.40 50 70 450 4 BNS-1565 1.50 65 60 400 5 BNS-1670 1.60 70 50 300 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 STORAGE OF PRODUCTS Do not expose rubber sheet to direct sunlight, sheets away from heat source, preferably in dark, air ventilated room will help give longer life & optimum properties Do not remove polythene packing before use to prevent it from exposure of atmospheric oxygen, ozone & polluted air. Do not store rubber sheet rolls in open, even after covering it with tarpaulin to protect from air & rain. Always keep rolls in vertical position ONLY Keep rolls away from solvent, oil & fuel storage. Do not use hooks while loading/unloading the rolls. Inspect sheet for smooth surface & hardness (with rubber hardness tester)
DESCRIPTION: Commercial Grade Neoprene rubber blended with natural rubber is a general-purpose sheet for most commercial applications. This grade of rubber is used as a barrier or gasket material and can also be used inside rooms for sandblasting and impact resistance for industrial needs. Commercial Grade Neoprene rubber sheet / roll are moderately resistance to oil, sunlight, ozone and oxidation material providing abrasion resistance, repeated flexing applications, wide temperature range (excellent cold temperature flexibility) and has a physical toughness. APPLICATIONS: Wear resistant pads, vibration pads, isolation mounts, buffers, diaphragms, industrial matting, water retaining structures and in industrial applications such as gaskets, corrosion-¬resistant coatings. For more information click here. COMMERCIAL GRADE NEOPRENE RUBBER SHEET NO GRADES NEOPRENE (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNPNR-15 15 1.65 65 20 150 2 BNPNR-30 30 1.60 65 30 200 3 BNPNR-50 50 1.55 65 40 200 4 BNPNR-70 70 1.50 65 50 250 PROPERTY: General purpose sheets / rolls resist moderate oil & heat resistance, fungus resistance, flame retardancy, acid & alkali resistance, sunlight aging & heat resistance up to 100°C. Best quality for sealing gasket, packing, mounting pad, machinery packing, manhole packing, as a mechanical applications without confect any fuel & also useful in marine parts due to good ozone resistance. PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with hydrocarbons, solvents, acids & alkalies. To maintain the sheet/roll in optimum condition they should be stored in cool and dark place. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Neoprene rubber is a chloroprene rubber, which has excellent mechanical property & good abrasion resistance. It gives good resistance to oil & heat, ozone, sunlight & weather and also gives good adhesion to metal surface. Neoprene rubber sheets / rolls are available for a range of applications in the industries. Many grades of neoprene are available depending on the application. These rolls will handle most tough industrial environments and moderate to heavy alkaline and chemical resistive situations. It is manufactured in pure neoprene rolls, commercial, medium strength, High Strength, Cloth Inserted, Antistatic, Fire Retardant, and Textured & in Strips. The temperature ranges from (-30°C to +100°C) in operation condition. APPLICATIONS: Neoprene rubber sheets / rolls are mainly used in sealing applications in construction sites & sound studios, general & industrial applications like sealing, gasket & packing to avoid leakages of oil, heat, steam, water, air, acid & alkali. It is also used in marine applications. It has flame retardant properties & good resistance to inorganic chemical products. 100% NEOPRENE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNP-1445 1.4 45 60 350 2 BNP-1555 1.5 55 70 300 3 BNP-1665 1.6 65 70 250
DESCRIPTION: Nitrile Rubber is a copolymer of butadiene and acrylonitrile. Nitrile rubber sheets are mainly used as oil & solvent resistance as it has good tensile strength, low compression set, flexibility & impermeability to gases. These sheets are very good resistance to petroleum based products having recommended for operating temperature from (-20°C to +110°C). APPLICATIONS: These sheets / rolls are mainly used for sealing, gasket & packing to avoid leakages from oil, solvent, petroleum based fluids, lubricating oil, transformer fluid & sealing against gases. PROPERTY: Very good resistance to petroleum based fluid goods & high temperature resistance up to 110°C. Very low-level permeability to gases. Poor ozone resistance. 100% NITRILE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNT-1240 1.2 40 60 500 2 BNT-1350 1.3 50 70 450 3 BNT-1460 1.4 60 80 400 4 BNT-1570 1.5 70 80 300 COMMERCIAL GRADE NITRILE RUBBER SHEET NO GRADES NEOPRENE (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNTNR-50 50 1.6 65 20 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 Store according to DIN 7716 standards. Products must be stored in cool, dry places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: EPDM rubber sheet / roll is very good weather-proof quality that makes highly recommended for the outdoor use, These sheets resist to oxidation, UV rays, Ozone, weathering & low temperature flexibility. The operating temperature range is from (-40°C to +130°C). EPDM rubber sheets / rolls are stable for long time due to its inert structure APPLICATIONS: EPDM rubber sheets are highly used for industrial & outdoor application like weather strips, drinking water applications, rain water sealing, protection against sunlight & heat gaining as a roofing membrane & acid resistance applications. Also useful as a liner in pulverizing system. PROPERTY: Very good resistance to water & water-based chemicals withstand temperature up to 130°C. Very good weathering resistance. Good resistance to mild acids, liquid fertilizer & break fluids. No resistance to oil & oil based products. 100% EPDM RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEP-1155 1.1 55 70 500 2 BEP-1260 1.2 60 80 400 3 BEP-1365 1.3 65 100 300 4 BEP-1470 1.4 70 70 250 COMMERCIAL GRADE EPDM RUBBER SHEET NO GRADES EPDM (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEPNR-50 50 1.5 65 50 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places Avoid contact with hydrocarbons, solvents, acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Butyl Rubber sheet / roll are a very low permeability to air & other gases. These sheets have excellent resistance to sunlight, ozone & oxidation. The operating temperature resistivity ranges from (-30°C to +110°C). It is resistant to most inorganic products and best resistance to mineral acids & alkaline. APPLICATIONS: These sheets / rolls are used for Chemical tank lining, Pharmaceutical stoppers, Acid protective clothing & many more applications. PROPERTY: Very good resistance to acids & alkalis. Very good for low resilience applications like shock absorber & vibration dampers. Not recommended its use in applications where resistance to oils & hydrocarbons is required. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BIIR-12560 1.2 55 80 350 2 BIIR-13065 1.3 60 60 300 3 BINR-60 (IIR: NR = 60:40) 1.3 65 70 350 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with hydrocarbons, solvents. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Diaphragm Rubber sheets are manufactured by inserting 1 ply & 2 ply Nylon Fabric used as Diaphragms for wide variety of applications specifically for Oil, LPG & solvent resistant applications. Recommended use for control valves, regulators, pumps etc. Diaphragm sheet is manufactured with high quality Nitrile rubber compound designed for long service. This rubber sheet is reinforced with multi-ply fabric to provide desired strength. The purpose of providing insertion is to provide additional strength to material in order to make it more pressure proof. Selection of fabric is available on request. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BDR-1370 1.3 70 80 300 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
Rubber Stocks
Since 2018 year, we are completely carried out the whole production line from mold, Refining ,trimming, Assembly with the most professional rubber vulcanizing equipment, the innovative R&D sprite, strong production capacity, strict quality control that make us well to produce the material of NR,NBR, EPDM,SIR,LSR,CR,,SBR,FKM,PU,PP,PVC,PE,PC,ABS etc, Now the capacity more than 20000000pcs/day to ensure the lead time on time! We are cooperate well with domestic and abroad, such as USA Germany, France, UK, Italy, with famous brand, such as Kohler, Dollar General, B&Q and so on. We are ISO9001,IATF16949, Reach and ROHS ,FDA approvals. All kinds of business cooperation are welcomed,
