High quality, good performance, reliable and cost-effective. Without packing
The straight side can be groud to be flat and vertical to the surface of the glass. And it can bevel the arris of the straight edge to angle of 45 degree. The rough grinding, fine grinding, polishing for flat edge and arris bevelling can be finished at one travelling. Continuous processing can be taken for glass of the same thickness. The shineness of the glass edge surface after being processed will be almost the same as the glass flat surface.
Pneumatic clamping of the glass sheet during the drilling operation of Opposite drilling head.BZ0213 glass drilling machine is equipped with a glass supporting table. Major Technical Specification Drilling Hole Diameter 4-130(mm) Glass Thickness 2-20(mm) Space Between Drilled Hole Center And Vertical Post 1050(mm) Total Power 1.7(kw)/2.2(kw) Dimension 1.65x2.6(M) Weight 900(kg)
It can grind and polish flat edge with arrises. It adopts mechanical stepless speed adjustment and can be adjusted to suit different thickness glass. Major Technical Specification Speed 0.5-5(m/min) Max. Grinding Amount 3(mm) Glass Thickness 3-25(mm) Min. Glass 80x80(mm) Total Power 22.8(Kw) Dimension 6.6x1.1(M) Weight 2850(kg) Max. Glass 3000x3000(mm)
BQ2500 Glass horizontal washing & drying machine is working for various flat glass and specially working for LOW-E glass. The structure of machine is made of painted steel; All parts in contact with water are waterproof materials made. The machine equipped with 4 pair of brushes and air-knife so that generate a perfect washing and drying, All driven-rolls are steel made, suitably coated with vulcanized and rectified rubber, soundproof blower, is placed on the top of drying section, to ensure a strong force air for drying. The washing section is well controlled by PLC, and it is able to be completed lift up or low-down for the purpose of different thickness of glass. W26 horizontal washing machine is an particular design for Low-E glass and other coated glass, it is also can perfectly perform washing and drying for all kind of flat glass. Min. Size 300*350mm Max.Size (Width) 2600mm Glass Thickness 3-60mm Processing Speed 1.2-6m/min Intalled Power 39KW No. of Burshes 4pairs Dimension 8500*4500*3500mm Weight 4500kg
KV9 Glass Flat Edger & Variable Miter Machine 1. Brief Introduction: 1.1. This glass edger and variable miter machine is able to grind and polish the miter angles of the glass, with bottom edge polishing and rear seaming all at the same time. 1.2. The control system of this glass miter machine uses a Mitsubishi PLC control unit. 1.3. The input and output conveyor adopt timing belt which can improve the transmission precision. 1.4. The processed glass surface is very bright and smooth, approaching the original glass surface. 1.5. The mitering angle of the glass machine ranges from 0 to 60 degree. 2. Technical Parameters 1. Processing glass thickness: 3~~25mm 2. Miter angle: 0íp~~60íp 3. Min size processing glass: 80mmí-80mm 4. Processing speed: 0.75~~3.75m/min 5. Installation power: 20.3KW 6. Size: 7800 x 1400 x 2500mm
KV11a Glass Flat Edger & Variable Miter Machine 1. Brief Introduction: 1.1 This glass mitering edging machine is able to process and polish all miter edge, bottom edge and arris on glass at one time. There are 3 wheels for each arris. 1.2. The control system of the glass mitering edging machine uses a Mitsubishi PLC control unit. 1.3. The input and output conveyor of the machine adopt timing belt which can improve the transmission precision. 1.4. The mitering angle ranges from 0 to 60 degree. 1.5. Different options: Digital display, PLC. 2. Technical Parameters: 1. Processing glass thickness: 3~~28mm 2. Miter angle: 0íp~~60íp 3. Min size processing glass: 80mmí-80mm 4. Processing speed: 0.75~~3.75m/min 5. Installation power: 23.3KW 6. Size: 7920 X 1400 X 2500mm
Technical data of water jet cutting machine The machine has three parts: cutting table, intensifier pump, controller 1) We have two kinds of cutting table: bridge style and flying arms style, their technical data is as follows: Z-axis journey is 150mm Three-axis control, Auto zero positioning Way of drive : Servo ( drives and motors are FUJI brand from Japan ) All screw and linear guide are ABBA brand from Taiwan Control accuracy: í+0.01mm Cutting accuracy: í+0.2mm 2) The intensifier pump we introduce you to use is made in China, its technical data and components are as follows: Type of pressurization is hydraulic. (The water is pressurized by using the fluid pressure intensification principle) Max. oil discharge is 90 L/min Max. water discharge is 3.7L/min Max. diameter of orifice is 0.3mm Max. operating pressure is 380MPa Continuous operating pressure is 330MPa Power requirement : 37KW,380V/50HZ Type of shift is electronic maintenance free accumulator whose capability is 1.3L using American technology intensifier is from America 3) For the controller,we research and develop our own professional software, components are as follows: EVOC brand Industrial Personal Computer and 17BENQ LCD specialised waterjet cutting software Omron brand PLC instead of relay Windows XP based. Soft packing.
Compact, robust Safe, ex-proof Power source:compressed air Max.Output pressure:100mpa Medium:oil, water, corrosive liquids Hydraulic power packs include lbs130wl model are complete hydraulic units ready for connection which are provided for generating operating pressures up to 100mpa.It is suitable for powering a variety of medium, such as oil, water or corrosive liquids. As the pressure will be generated by means of a pneumatically operated pump.The electric connection will not be necessary. To operate this system, the air driven liquid pump have to be equipped with the air control unit combined filter and water seperator, pressure-regulating valve, pressure control gauge as well as manual relieve valve.In this operation, the pump will be mounted to the stainless steel tank in the closed cabinet in a compact and space saving manner.Pressure gauges, valves and pressure regulators will be fitted on panel. The desired operating pressure can be attained by adjusting the driving air pressure.When the driving air pressure and the output pressure reach the balance, the pump stops filling pressure and the output pressure stays at the preset value. This hydraulic unit can be used for all kinds of pressure testing and test tools for research and test institutes or for other functions requiring a determined pressure As per buyer's requiement
Air driven gas booster Rugged, efficient Pressure range:1.6~80mpa Seven pressure ratios available Best price, high quality Air driven gas boosters are high pressure reciprocating pumps used for gases boosting, driven of compressed shop air. Sta series boosters are single acting, single air head driven type.(except model sta02 and sta05.They are double acting models).They have to be prepressurized at the inlet port so as to meet with the outlet pressure requirements, which value will be variable based on the permitted maximum outlet pressure. Sta series gas boosters are suitable for the oil free compression of air and industrial gases like nitrogen, helium as well as flammable and risk gases like hydrogen , oxygen and natural gas.Air drive pressure from 1bar(14.5psi.) to 8bar(116psi.). Provide for operating pressures up to 80mpa. As per buyer's requirment
Major technical specificationsíg Speedíg0.5-6m/min Min.Processed sizeíg100í±100mm Max.Processed widthíg3000mm Glass thicknessíg3-25mm Max.Arris grindingíg2.5mm Max.Hemline grindingíg3mm Angle rangeíg45óx Total poweríg 19.5kw Weightíg3200kg Overall sizeíg 6700í±1000í±2500mm
Major technical specificationsíg Speedíg 0.5-6.5m/min Min.Processed sizeíg 230í±230mm Max.Processed widthíg 2500mm Glass thicknessíg 3-30mm Max.Hemline grindingíg 5mm Max.Arris grindingíg 3mm Total poweríg 52kw Weightíg 7600kg Overall sizeíg 4850í±4600í±1900mm Working heightíg 880mm
Glass loading and breaking Station Cut size of Jumbo Glass : 3210 x 6000 mm Machine functions are CNC Controlled Data transfer with a 3.5disk CNC controlled optimisation and a unit for printing on paper Movement transfer and measuring with gear system Adjustable cutting speed Table movement to vertical position for onlading glass plates Easy movement of glass plates by air cushion Able to separate cut glass with pneumatic controlled breaker bars Electrical system compliant with general safety rules.
Automatic or manual control pf machine function Adjustable working pressure Adjustable material flow rate High pressure safety system, Timer system for switching on / off Low temparature safety system Able to work with different profile thicknesses Temperature control system Electrical system compliant with general safety rules.
Washing with 4 or 6 special spiral brushes and thermostatically controlled hot water and rinsing. Washing speed adjustable. Possibility to wash coated glasses. Siemens electrical components. Inspection lights for quality control. Noise isolated body. Stainless steel water tanks valve system for controlling water level in tank. Working direction from right to left. Manual Assembling and pressing for double or triple IG s. Panel press system.
Adjustable Mixing Ratio Adjustable Hydraulic Operation Pressure High pressure safety system Heating system for base component Base and Catalyaer Component pumps with hydraulic feeding Mixer unit for homogen mixing of two componenets Adjustable material flow rate Warning system for starting the curing of mixed material Warning System foe low material level Electrical System Compliant with general safety rules .
Stainless steel nois isolated closed (open) top washing cabin 4 or 6 units of balanced brush rollers in the washing unit revolving at high speed Adjustable glass transport speed High sensetive brushes that can wash coated glass Homogeneous brush contact fof different glass thicknesses Draying fan equipped with a heater placed in a noise-isolated housing Stainless steel water tank equipped with a heater Float-valve system for controlling the water level in the water tank Standard working direction from left to right Electrical system compliant with general safety rules.
Feature: this machine is suitable for grinding and polishing peripheral edge and bevel of different shape flat glass. It can process semi-automatic procession for circular glass. Five-star suction tray adopts vacuum clamping. Its rolling speed can be adjusted at random during working. Install and adjust easily while processing different size glass. Technical specifications: 1. Thickness: 3 ~ 25mm 2. Bevel edge angle range: 0 ~ 20 degrees 3. Maximum width of bevel edge: 32mm 4. Maximum diameter: 2000 mm 5. Minimum diameter: 120 mm 6. Power: 3.2 kw 7. Weight: 800 kg Packed by plastic film or wooden case.
Glass sandblasting machine Hsp330b (manual) This machine is suitable for sandblasting the surface of glass, metal and ceramics etc and different designs and characters. It makes processed articles form stereo designs or become colorful carved craftworks with color and paint. This machine is highly efficient, easy to operate and repair. Technical specifications: 1. Max processing depth: 3mm 2. Working pressure: 0.4 - 1mpa 3. Compressor power: 0.6 - 0.9m3/min 4. Wind machine power: 220v/50hz, 450w Technical specifications: 1. Processing dimensions: min: 200 x 500mm max: 1500 x 2000mm 2. Processing thickness: 3 - 25mm 3. Spray gun traveling speed: 0.5 - 12 m/min 4. Sand spraying speed: 10 - 15 m2/h 5. Working pressure: 0.8mpa 6. Air compressor power: >12kw (>1.5m3/min) 7. Total power: 3.6kw 8. Size: 6100(l) x 2000(w) x 2500(h) mm
Hxm series glass straight-line beveling machine which processed with three diamond wheels for coarse grinding, one wheel for base modification, three wheels for refine grinding and two wheels for pneumatic polishing. The grinding speed is regulated by a stepless regulator. It specialty adopt beveling wheel which can whole progress and also can lifting integrally. It compare to traditional front beam or back beam's lifting, it more pithiness structure, more stability, higher grinding precision. Hxm261pt/hxm9320t straight-line beveling machine has adjustable front beam, can process glass size from 50-3000mm. Hxm261p/hxm9320b straight-line beveling machine is designed for beveling glass size from 150-3000mm. Hxm261pt & hxm261pt adopt plc control system and displays the thickness and length of processed glass by lcd screen. Hxm9320t & hxm9320b are for manual operation. Technical specifications: Hxm261pt 1. The number of grinders: 9 2. Grinding speed: 500 - 2500mm/min 3. Maximum beveling width: 35mm 4. Range of bevel angle: 3 - 20 degrees 5. Glass thickness: 4 - 20mm 6. Size of processed glass: max: 3000 x 3000mm min: 50 x 50mm 7. Power: 18.5kw 8. Weight: 4800 kg 9. Size: 7760 x 1400 x 2450mm Hxm9320t 1. The number of grinders: 9 2. Grinding speed: 500 - 2500mm/min 3. Maximum beveling width: 35mm 4. Range of bevel angle: 3 - 20 degrees 5. Glass thickness: 4 - 20mm 6. Size of processed glass: max: 3000 x 3000mm min: 50 x 50mm 7. Power: 17.8kw 8. Weight: 4800 kg 9. Size: 7760 x 1400 x 2450mm Packed by plastic film or wooden case.