Parameters Finish: Clear Gloss: 70% Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: White Gloss: N/A Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: White Gloss: N/A Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: White Gloss: 80% Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: Clear Gloss: N/A Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: Clear Gloss: 30% Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: Clear Gloss: 70%Application Methods: Roller / Brush Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: Milky White Gloss: N/A Application Methods: Patch Substrate: Rubber, Mango Exposure: Formulation
Parameters Finish: Clear Gloss: N/A Application Methods: Wipe Substrate: Rubber, Mango Exposure: Formulation
Printing Parameters Squeege: 60-65 SHORE Mesh: 120/inch Tension:� 25 N/cm2 Clean Up: Water Strokes:  3 Rounds:  2 Printing Application 1. Blow dry print in between rounds using hairdyer or other methods. 2. Allow for 2 â?? 4 hours ambient drying. 3. Heat cure at 130 â?? 160oC for 2 minutes. 4. Allow for 24 hours after heat cure before any physical testing of prints. Formulation White Print White: 97% Fixer: 3% Colour Print White: 15-20% Clear: 70-75% Colour Pigment: 5-7% Fixer: 3%
Heat transfer coating for photo or image transfer on wood. Acrylic-polyester nature, ready for use .....
Sublimation coating with acrylic-polyester nature ( in concentrate form ) for sublimation to wood and plywood. Other adhesives with 2 or more components, the mixture of they must be used within 4-5 hours. Unlike these, this concentrate does not mix with other components and is ready for use, can be used whenever needed even in small uses. This makes it economical. This is very easy to use it, with paint brush or paint roller . Sublimation coating with acrylic-polyester nature in paste form (concentrate). The concentrate is ready for use. For the decoration of different wood materials, such as wood board and plywood, through sublimation
Screen printing coating for sublimation on cotton. Recommended mesh number: 90 mesh - 110 mesh Drying with air (ventilated) kiln at 120-140 degrees Celsius (or hair dryer at medium temperature). The process is sample: 1. Print the coating 2. Dry (recommended ventilated kiln) 120 - 140 degrees Celsius for 2-3 minutes (or hair dryer in medium heat, or room temperature for 24 hours) 3. Sublimation at 180 - 182 degrees Celsius ( 355-360 F ) for 30-40 sec.
Description Two-component, air drying polyurethane based clear. Recommended Use :- This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system. Physical Data :- COLOUR : Clear FINISH : Smooth & Glossy SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 16 sq.mt / ltr at a DFT of 25 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Indefinite COMPATIBILITY : Can be applied on Epoxy primers and oleo-resinous primer and coated / over coated by two component paints like Epoxy, PU, etc.
Features and Function Can replace varnish and paint and other coatings, directly used for machine maintenance, indoor wood flooring, wooden ceiling, sauna board, wooden balcony handrails, etc. Outdoor wooden floors, flower shelves, wooden houses, pavilions, fences, wooden Bridges, boats, chairs, wooden farm tools, etc.
AFFIX 1K  PU COATING water proofing  is a single component liquid applied, highly permanent elastomeric polyurethane based coating. It is designed to give long lasting, cold curing, maintenance free and superior waterproofing protection for concrete and steel substrates. It is UV stable coating and specially formulated for external applications.
Electrophoretic Coating Cathodic Electro Coating used in Metal and Jewelry Coating
Tung oil or China Wood Oil is a drying oil obtained by pressing the seed from the nut of tung tree (Vernicia fordii), widely used in laminate industry, printing ink, oil paint and wood finishing.
Description CP-358 Multi-purposes Paint is based on specific polymer resin and a variety of materials with water resistance ,abrasion resistance, weather resistance characters. This refined dry fast paint can be used in cement ,metal ,wood ,asphalt surface to meet your particular requirement and very economy. Owing to excellent materials , strict QC and production process , Carmine Paint can offer the advantages of time- saving , easy usage . Application * used in multi-kind materials, such as metal, wood, cement and asphalt. * Indoor, outdoor paint. * Line Marking. Characteristics Durable hard and tough film. Excellent adhesion. Excellent abrasion and corrosion resistance. Package 25KG / Iron durm Color : white / yellow / red / green Cover ability : 8 ~ 10 m�²
Description CC-610N is a 2k topcoat which cured by non-yellowing isocyanate. Feature â?¦ Solvent-free, friendly to human. â?¦ Compression and impact resistant. â?¦ Chemical resistant as its special structure. â?¦ Suitable for critical area (0~80â??). â?¦ Suitable for food factory, freezer, medicine plant, chemical plant, laboratory..etc Usage Used as a topcoat on surface of concrete and metal, bridges and steel structures. Package 5 gal per set
