TI UNIT compact roof top chiller units are manufactured in type of air cooled in capacities of 5 to 360T.R. in one to four circuited configurations. In all TI UNIT compact roof-top chiller units the frames and body are from galvanized steel & stainless steel (316l) (option) the chassis made steel channel in appropriate thicknesses and all of units are completely painted in the proper thickness. Evaporators are high efficiency shell and tube heat exchangers, designed based on TEMA. Condenser of compact rooftop chiller unit made of plated coil, designed based on TEMA. Chillers with plate type heat exchangers are available upon request. TI UNIT compact roof top chillers can be designed to operate with R-22, R-407C and R-134a refrigerants. Safety controls installed on all units include high, oil and low pressure cut-outs, compressor safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Automatic condensing temperature control: A controller, factory installed on each unit automatically stages the condenser fans allowing the unit to start. With this controller the condenser fans start stage by stage. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufacturers. Electrical safety measures such as three phase controller and circuit breakers are, available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed. Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
TI UNIT screw chillers are manufactured in two types of air cooled and water cooled in capacities from 50 to 560 T.R. in one to four circuited configurations. Evaporators and condenser Chillers with plate type heat exchangers are available upon request. For further related technical information, please send your inquiries to TI UNIT mfg. group. TI UNIT screw chillers can be designed to operate with R-22 and R-134a refrigerants. Bitzer screw compressors suitable for use with R-134a refrigerant are available in two versions (m.vr.1 & m.vr.2) which can be used in the chillers as required. Safety controls installed on all units include high and low pressure cut-outs, compressor oil level control safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Compressors are by Bitzer which happens to be one of the best and most reliable brands. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufactures. Electrical safety measures such as three phase controller and circuit breakers, are available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed. TI UNIT screw chillers are also available upon request for industrial applications in both Air Cooled and Water Cooled types; Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
TI UNITS Reciprocating Water Chillers are available in two types of air cooled and water cooled in capacity range of 5 to 240 tons of refrigeration and compressor configurations of one to four. Evaporators and condensers are high efficiency shell and tube heat exchangers designed based on TEMA (Tubular Exchanger Manufacturers Association) standards. Safety controls installed on all units include high and low pressure cut-outs, compressor oil pressure safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat. Whatever mentioned above, are all chosen from the most recognized controls manufacturers in the air conditioning industry. Compressors are by DWM COPELAND and BITZER which happens to be one of the best and the most reliable brands. Raw materials such as copper tubes, fittings and valves are supplied by well respected manufactures. Electrical safety measures such as three phase controller and circuit breakers are available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed.
In all TI UNIT air handling units the frames are from aluminum profiles while the chassis and body panels are made from galvanized steel sheets in appropriate thicknesses. All units are completely painted in the proper thickness. Blower(S): Double width-double inlet centrifugal fans with forward curved blades are normally used for low pressure drop requirements as opposed to fans with backward curved blades which are for high pressure drop applications. Fans and housings are made of galvanized steel each set off a plus other related components such as shafts are statically and dynamically balanced, shafts are selected from proper material and size. Other power transmission components such as pulleys and belts are also suit ably chosen depending on the required fan speed and electric motor power. Fan(s) and the corresponding electric motor(s) are installed on an independent chassis which is itself installed on the main chassis using vibration dampers in order to eliminate transfer of vibrations to the structure. To further reduce the effects of vibrations, fan outlet (s) are also connected to the structure via flexible material such as canvous. All 380V/3/50Hz electric motors are selected with insulation class of (f) and ingress protection of (IP- 54). Electric motors with ingress protection of (IP- 55) are also available upon request. Coil (S): Cooling and heating coils or either one of the two depending on the Requirement May be installed. Cooling coils are available in two, types of chilled water and direct expansion (D.X.) as per clients requirements. The chilled water coils are constructed of 5/8 O.D copper tubes plate finned (8, 10, 12 or 14 FPI) in aluminum or copper upon request. The D.X. Coils are constructed of 3/8 OD copper tubes also plate finned (10, 12 or 14 FPI) in aluminum or copper as required. The chilled water for cooling coils in to be supplied by a water chiller and in the D.X. coils cooling is provided through the use of refrigerant such as R-22, R-407c or R-134a. Chilled water coils may be requested in 4 or 6 rows and as to the D.X. coils, they are available in 4 or 6 row configurations. Heating coils are available in two types of hot water and steam. The hot water coil similar to chilled water coil is offered in 1 or 2 row configurations. Steam heating coils are constructed of 1/2 seamless steel pipe spiral finned in aluminum or copper. Coils in 1 & 2 -row configurations are available upon request. Mixing box: Fresh and return air streams are mixed in the mixing box .An independent air damper is included for each air stream. Air Dampers are manufactured from aluminum in opposed blade configuration and are air sealed through the use of rubber strip gasket. Damper actuators ma y be easily installed when required. Washable aluminum filter modules 2 inches in thickness are arranged in (V) type configuration inside these boxes. Housing for
Hvac units.
Rubber Process Oil (RPO) Tailored to enhance your rubber products, our RPO is the choice for those who demand flexibility, durability, and performance. It integrates seamlessly with various rubber compounds, delivering exceptional results in tires, automotive parts, and industrial rubber goods.
Superior Quality Functional Bitumen, sourced from the best refineries, our bitumen meets international standards for quality consistency. This bitumen is obtained by blowing hot air at a temperature of 200 to 300 degrees into pure bitumen. with a strong logistic network, we gaurantee timely and secure delivery to your projected port.
Electrical, transformers, under floor boxes, inner consent box, cable trays, solar power products, cables, lugs, glands, cable protection covers, earthing, lightening materials, overhead line accessories, towers, termination kit, HVAC, mep equipments, electrical lights, cement, steel pipes, conduits, sockets, cable laying equipments, all electromechanical equipments, building materials, sanitary wares, transformers, ups inverters.Construction, consultancy services, trading tourism, ticketing
We are Official Representatives for MTC and another spare part companies, we can supply you all welding materials and parts for your car, we are in several country supplying already 10 year.
Oil and gas equipment, hydraulic equipment, safety equipment, safety equipment, valves, pump equipment, smoke detector, electrical equipment, fire equipment, honey wall, hvac equipment, building material.
Sand blasting indian garnet, steel grit & steel shots, aluminium oxide, glass beads, sand blasting pot, blasting accessories, copper slag grit, welding electrode, wire nail, binding wire, green shade net, industrial air coolers.
This sedimentary rock which is composed primarily of Calcium Carbonate is integrally a multi-functional mineral used in industries for centuries. Limestone as one of the oldest minerals due to its very enduring geological evolution possesses different forms in nature and exhibits different colors. Its properties such as hardness, compactness, imperviousness, and durability have a significant role to play when it comes to its uses which are vast and versatile. This oldest component of ancient landmarks in the world is still practically an inseparable part of industries today. Middle East is amongst the top commodity traders of this mineral. And Arij is honored for having supplied the highest quality of Limestone and specifically the highest purity of 99% at a cost-effective price to different countries. This mineral has enormous diversity of industrial applications and what follows are some key uses of Limestone: Steel industry Construction Materials Refractory Sugar Refining Agriculture Paper manufacturing Glass Manufacturing Leather Tanning Pharmaceutics Food Industry
HDPE is widely used to produce pressure pipes, gas distribution pipes, bottles, drums, barrels, white goods, and machine parts, insulators, toys, electrical and electronic goods. Grades: The most important commercial grades of HDPE polyethylene materials are EX5 / HI500 / EX3 / BL3 / PE100 and 6040. Here at Arij global trading, we have established long-lasting and close partnerships with manufacturers and petrochemical companies from the area, which brings us valuable complements of supplying all grades of HDPE. We are able to provide any considerable quantity of various grades of HDPE in granule or powder form. The granules or powders can be shipped using jumbo bags or smaller packages, based on our dear customers' requirements.
Car, bus and truck spare parts.
Tomato ketchup, paste, hot sauce, non food products like dish wash liquid, hand liquid soap, glass cleaner, aerosol products like insect killers, air fresheners.
Car & truck parts.
Electronics & home appliances, IT products.Distributor
Kia / Hyundai genuine spare parts.
Genuine spare parts for Nissan, Tata, Tata Daewoo, Nissan Diesel, Proton, Tadano.
Auto parts, oil filters.
