Elevator Access Control systems allow users to access to designated floors. Elevator access can depend on the user’s classification, the time zone, which elevator is being approached, and the armed state of a floor. In addition, changes to the status of a zone can either cause elevator to grant access to a floor, or cause the elevator to deny access. By using one or more of these attributes, you can create elevator access control policies that are extremely flexible and secure. By using an elevator access control system, you can separate the general public and unauthorized users from the authorized users. Features: • One Controller per elevator car: Per elevator car one Elevator Access Controller (EAC) is must. There is no communication between two distinct elevator cars and only one card reader can be interfaced, which will be inside the elevator. • Supports up to 52 Floors: An EAC supports 12 floors including ground floor and a basement floor. It can be attached to Elevator Access Control Expansion Board (EACEB) using FRC connector which supports additional 10 floors. Each EAC can be attached to maximum 4 EACEB to control a total of 52 floors using 1 EAC and 4 EACEB with the option of floor control relay from the EAC being directly interface with the elevators floor control buttons. • Supports elevator car floor selection button for programming: The elevator floor buttons are used for programming the user cards in standalone mode. The programming mode is protected by a master card. On showing it one can add, edit or delete a user card. While adding or editing, one can select floors where the user is allowed. • Supports Fail safe mode: On power failure of EAC elevator car works in normal mode in which anyone can move to any floor. • Inbuilt RJ45 Network Interface: Leveraging on the merits of IP based system; it can easily be hooked up on the existing TCP/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. • Field Upgradable Firmware: Facility to onsite upgrade the firmware over Ethernet interface so that any customization or new version can be easily upgraded without any need of removing the device Advantages: • Easy to install and configure • Embedded network interface for easy connectivity • Industry standard weigand input facilitates to connect with any readers. • Cost saving For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
TwinXs2c is one of the most successful controller presently available in the market. Client includes large corporates like firstsource, Ranbaxy, Myntra and many more. This is one of the most flexible hard ware with 4 completely configurable outputs and 8 General purpose inputs. Further integration with fire is possible very smoothly. It supports weigand / HID based readers Features: 2 door / 4 reader Controller Supports access control of up to 2 doors in all respect including 2 entry readers, 2 exit readers, 2 locks, 2 exit switches etc. Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Network interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCR/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware Facility to onsite upgrade the firmware over Ethernet interlace so that any customisation or new version can be easily upgraded without any need of removing the device or physical presence of the engineer near the device Protected Enclosures Both controller & power supply unit are protected with suitable housing so electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking Facility of door interlocking is available. The system allows creating a group of doors such that access to a door .thin the group is allowed only when all the other doors are in closed condition. Excellent Price Performance Ratio With a lower price to performance ratio ROI is automatically enhanced, the factor contributing to higher ROI is not only very competitive pricing but also higher accuracy rate offered by the product Fully configurable GPI and GPO Optically Isolated inputs for 4 Door Sensor, 4 Exit Switch & 8 General purpose digital inputs along with 4 General purpose relay outputs. These are fully configurable. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
BioStamp 3S is a standalone finger print recognition based access control and attendance recording system. It is a field proven product incorporating industry’s most advanced and powerful finger print reader. It boasts of a robust metal enclosure for rugged industrial usages. It comes up with various options to suit varied requirements. It has been seamlessly integrated with Mifare & RFID technologies. Standalone Biometric Access Controller Get distinct advantage of field proven fingerprint authentication technology and rugged optical sensor for allowing access to any restricted area. Supports inbuilt multiple options of RFID card technologies for 1:1 match. Ultra Sleek Design BioStamp series of product boasts of high aesthetics with ultra modern design, sleek form factor helps in even installing the product directly on the door panels. Color TFT display (1.77”) makes it a unique device of this size. Data Communication This device also supports IPv6 protocol making it future ready. Optional Wifi enables the device to hook up with Wifi network for instant data transfer. In addition it supports host of protocols such as SNMP, SMPT, HTTP, FTP, SSL & NTP Inbuilt Camera The device has an inbuilt VGA camera to capture the images. It can be configured to capture the image on certain pre-defined events e.g. an invalid attempt to access the restricted area can be captured and used for verification. IP65 Weatherproof Housing Product enclosure is designed to meet IP65 standard of protection. This gives complete protection from dust particles, rainwater, airborne pollutants and such other environmental threats. Field Upgradable Software Facility to onsite update device software through Ethernet interface. The product updates can easily be applied without the need of removing device and sending it back to the service center. Rugged Optical Fingerprint Sensor Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verifications results. Auto finger update helps in keeping track of finger changes over the period thus takes care of dry, wet and swollen fingers. Tamper Proof Device offers security and generates alarms in case someone tries to fiddle with it. The alarm can be in soft mode e.g. on computer screen or alert on a predefined email. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Complete Visitor Management System with dual interface of client server application and web-browser support and with Multiuser environment. It has been seamlessly integrated with NetXsControl(Access Control Software) for visitor access management. It can also be customized as per specific requirement of customer. Features: Client/Server Architecture with Web Client Support Easy Installation and deployment Reduces the total cost of deployment Integrates with Spectra's Attendance & Access Control Software Windows 200/XP/ VISTA compatible. Visitors Photo Capture Visitor Pass with Visitor's Credentials and printing User customizable Visitor Pass format Track Entry and Exit of visitors Visitor Pre-registration Frequent visitor declaration (Registered Visitor) Record movements of visitor on premises Entry of Assets being carried Restrict visitor access to specific zones on your premises. Visitor scheduling by employees for prior intimation to security staff Appointment Scheduling and reporting User Password Authentication Software User Rights Administration User Friendly GUI and Entry screens Email/SMS sending to visitors prior to appointment Extensive reports to tract visit details and excess Export reports to various formats. Excel Advantages: Improves efficiency of the visitor Check IN Process Monitors visitor traffic and waiting times Effective Verification of visitors Helps in Prior Planning for Resource booking Visitor Categorization Better control over visitor movements Restricted accessibility to visitors For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
The door interlocking system is used to control the entry of a person to a secure area such as a clean room, research lab, etc. where dust or small particles may be a problem or security is of high concern. In its simplest form, the door interlocking is composed of 2 doors that are electrically interlocked in such a way that the doors cannot be opened simultaneously. Another example of Door Interlocking is Man trap The 8 Door Interlocking Terminal can handle up to 8 doors ( 16 IN/OUT switches ).Thus logic can be built up around the number maximum number of doors ( 8 ) i.e. the manner in which they need to open or close. The Pass-through authorization is validated by a switch or the DIT can operate in a switch-less mode. Spectra’s DIT800 from the Enclava series caters to this requirement of 8 Door Interlocking. Features: • Door Interlocking with Buzzer and Led indicator: Door Interlocking Terminal (DIT) controls interlocking of doors 8 doors using DOTL signals. For user interface there is one switch at entry and EXIT side of a door. Buzzer and LED indicators are used to provide users with visual feedback as to when a door may be accessed. For user convenience, a green light is typically used to signify that a door is ready for access and a red light to indicate that a door is un-accessible. (Additional capability providing Digital outputs which may be utilized for up to 4 more relays controlled by the DIT) • Operations: Only one door may be unlocked or open at one time. Unlocking or opening one door automatically secures all other doors within the designated area. Lock relay contacts will allow low voltage red and green LEDs to be utilized for user feedback. • Programmable: Door interlocking groups can be programmed for 8 doors. User can program interlocking groups through serial communication. • Supports switch less operation: DIT can be used without switch in which led will indicates that user can open the door or not. Switch less operation is same as with switch except that all locks will remain open initially and will get closed if one of the doors of interlocking group is open. Advantages: • Easy to install and configure • Switchless operation • Cost saving For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Metrial:HDPE&PET.1.8*6m,2.0*6m also as your requairement iso9001 sgs ,4kg
Material ... PP (Polypropylene) Thickess ... 0.15~2.0mm Printing ... offset printing, Silk screen printing Special ... Glitter, foil, Hologram, Twinkle glue, spot UV
- Fresh and plentiful design, suitable for pupils and students. - Thin and regular writing lines. - The barrel is decorated by transfer film. 12 pcs/box, 50 boxes/carton
- Fresh design, suitable for pupils, students, office workers. - Reliable tip with Nickel Silver housing and durable Tungsten Carbide ball. - German high quality ink conforms to ASTM D-4236 and EN 71/3 standards. 12 pcs/box, 50 boxes/carton
The Air Max is for intercepting all kinds of dirt coming into indoor from outside. By using HEPA filter.
Please contact us for further information Please contact us for further information
Please contact us for further information Please contact us for further information
Automatic Optical Turnstile Factory Optical turnstile Main Functions: (1) Optical turnstile Easy to install, use and maintain. (2) When power off, the barrier arms will keep open (for safety). (3) Infrared sensor function. (4) Optical turnstile can be integrated with magnetic card, barcode scanner, counter, swallow machine, token accepter, and fingerprint machine and so on by standard electrical interface. Optical turnstile Specifications Sheet: Automatic Optical Turnstile Factory Item: Description: Material: 304 S/S, Arm- Plexiglas Thickness of Ply: 1.2mm (Standard) Dimensions: (L)1200* (W)280 *(H)990 (mm) Finishing: Brushed (Standard) / Fingerprint processing Pass width: 550mm Weight: 80Kg Operation direction: Single direction / Bi-direction Power Voltage: AC220V +/- 10V 50Hz AC110V +/- 10V 60Hz Optical turnstile Specific Function: (1) Optical turnstile alarms automatically if someone passed illegally. (2) The whole system runs smoothly, low noise, no mechanical impact. (3) If someone stands in the lane, the optical turnstile will not pen even the card reader gives relay signal to the barrier. (4) Anti-trailing function, the barrier will lock if someone wants to burst in without swiping the card. (5) When power off, Optical turnstile arms will open automatically, to meet the special needs of users and fire safety requirements. (6) Infrared sense to prevent pinch pedestrians. (7) Standard communication interface, can connect with most of access control parts, also can control and manage wireless by computer. (8) When connect the access control system, you can know how many person through the machine by computer directly. (9) Passing direction will be shown by LED and passengers will know which direction is allowed to pass. (10) By software, the people who can pass through or not can be set to meet special request. (11) Automatic reset function. When the Optical turnstile receives an open single, but passenger do not pass through the Optical turnstile hallway within a specific time (Default 5s), machine arm will lock again. Limit passing time can be set. (12) ISO 9001 Quality Assurance and CE certification. Automatic Optical Turnstile Factory Infrared sensor Function: (1) Anti-pinch function: When people stand in the middle lane, Flap Arm will not close. (2) Illegal intrusion alarm function: When people illegal to pass, Flap will alarm automatically (3) Reverse intrusion closing function: When you swiped card if another people pass from the reverse side, Flap Arm will automatically close. (4)Anti-Trailing function: If someone wants to trail with you without swiped the card, Flap Arm will be locked automatically. Optical turnstile Applications: Amusement Park Airport Buildings offices Enterprises Exhibition centers Entertainment centers Industrial Living garden Museums Railways Stadium Seaports Ski resorts Schools Shops Supermarkets Subway Public Park Water Park And so on Contact info: Company Name: Daosafe Technology Co., Ltd. Export Standard Wooden Package
Access Control System Tripod Turnstile Gate Tripod Turnstile Main Functions: (1) Tripod Turnstile Easy to install, use and maintain. (2) Tripod Turnstile direction can be set as single-direction or bi-direction. (3) Arms auto drop when power off, complying with fire safety requirements. (4) Tripod Turnstile can be integrated with magnetic card, barcode scanner, counter, swallow machine, token accepter, and fingerprint machine and so on by standard electrical interface. Tripod Turnstile Specifications Sheet: Item: Description: Framework: 304 (Standard). Thickness of Ply: 1.2mm (Standard). Dimensions: (L)1200* (W)280 *(H)990 (mm) Finishing: Brushed (Standard) / Fingerprint processing Pass width: ¡¡¡ì1500mm (Can be customized)) Weight: 55Kg Operation direction: Single direction / Bi-direction Power Voltage: AC220V +/- 10V 50Hz AC110V +/- 10V 60Hz Work Environment: Indoor / Outdoor Pass rate: 35person/ minute Power Consumption: 20W/24V Operating Temp.: -15oC ~ 60oC Operating Humidity: 0 ~ 95% without concretion Emergency: Automatic arm drop down Input: 12v dry contact Access Control System Tripod Turnstile Gate Tripod Turnstile Specific Function: (1) Electromagnet lock, photoelectric unlock, long service life, High operation dependability and fast response. (2) The whole system runs smoothly, low noise, no mechanical impact. (3) Tripod Turnstile Self-test function, when power on, system restoration automatic. (4) Tripod Turnstile working modes selectable: bi-direction card reading; One direction cards reading and another no reading; one direction card reading and another freely. Working modes can be set in the control panel. (5) When power off, Tripod Turnstile arms will drop automatically, to meet the special needs of users and fire safety requirements. While power on later, arm should be lift by hand. (6) Tripod Turnstile easy integrate with computer to control and manage hallway access. (7) When connect the access control system, you can know how many person through the machine by computer directly. (8) Tripod Turnstile passing direction will be shown by LED and passengers will know which direction is allowed to pass. (9) Card reading memory or card reading without memory function can be set in the control panel menu according to your request. (10) By software, the people who can pass through or not can be set to meet special request. (11) Automatic reset function. When the Tripod Turnstile receives an open single, but passenger do not pass through the Tripod Turnstile hallway within a specific time (Default 5s), machine arm will lock again. Limit passing time can be set. (12) ISO 9001 Quality Assurance and CE certification. Access Control System Tripod Turnstile Gate Tripod Turnstile Applications Amusement Park Airport Buildings offices Enterprises Exhibition centers Entertainment centers Industrial Living garden Museums Railways Stadium Seaports Ski resorts Schools Shops Supermarkets Public Park Water Park And so on Contact info: Company Name: Daosafe Technology Co., Ltd. Export Standard Wooden Package
This unit features a deep-bed activated carbon filter that uses a special carbon blend to remove voc's (volatile organic compounds) which are the most common airborne chemicals in the home. The unit also includes a medical-grade hepa to remove 99.97% of airborne particles (pollen, dust, mold, bacteria, viruses, pet dander) down to 0.3 microns in size Activated carbon filter, 2.5" depth, medical-grade hepa, pre-filter. 18 lbs. Or activated carbon. 50lbs
ron pipe burner used as a commercial equipment in restaurant and big hotels, coated with black color and widely used item in united kingdom
We have sizzler base available in various categories like with handle and without handle, they also come with wooden stand available as per the sizzler base.
we offer the commercial hotel equipment brass jet burner that is can be used in high temperatures,available in different sizes
Nothing technical for the specification No particular sizes, packing are in boxes
8 antennas high power gps/ wifi/ 315/ 433 jammer Cdma800: 850-960mhz, gsm1800: 1805-1880mhz (dcs), gsm1900: 1920-1990mhz (pcs), 3g: 2110-2170mhz, gps: 1570-1580mhz, wifi 2.4g: 2400-2500mhz, 315: 315mhz, 433: 433mhz Total output power: 20w power supply: 50-60hz, 100-240v ac Jamming range: up to 70m, the jamming radius still depends on the strength signal in given area Dimension: 370x 140 x 51mm Full set weight: 4.0kg Nutral package
