Elevator Access Control systems allow users to access to designated floors. Elevator access can depend on the user’s classification, the time zone, which elevator is being approached, and the armed state of a floor. In addition, changes to the status of a zone can either cause elevator to grant access to a floor, or cause the elevator to deny access. By using one or more of these attributes, you can create elevator access control policies that are extremely flexible and secure. By using an elevator access control system, you can separate the general public and unauthorized users from the authorized users.
Features:
• One Controller per elevator car: Per elevator car one Elevator Access Controller (EAC) is must. There is no communication between two distinct elevator cars and only one card reader can be interfaced, which will be inside the elevator.
• Supports up to 52 Floors: An EAC supports 12 floors including ground floor and a basement floor. It can be attached to Elevator Access Control Expansion Board (EACEB) using FRC connector which supports additional 10 floors. Each EAC can be attached to maximum 4 EACEB to control a total of 52 floors using 1 EAC and 4 EACEB with the option of floor control relay from the EAC being directly interface with the elevators floor control buttons.
• Supports elevator car floor selection button for programming: The elevator floor buttons are used for programming the user cards in standalone mode. The programming mode is protected by a master card. On showing it one can add, edit or delete a user card. While adding or editing, one can select floors where the user is allowed.
• Supports Fail safe mode: On power failure of EAC elevator car works in normal mode in which anyone can move to any floor.
• Inbuilt RJ45 Network Interface: Leveraging on the merits of IP based system; it can easily be hooked up on the existing TCP/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server.
• Field Upgradable Firmware: Facility to onsite upgrade the firmware over Ethernet interface so that any customization or new version can be easily upgraded without any need of removing the device
Advantages:
• Easy to install and configure
• Embedded network interface for easy connectivity
• Industry standard weigand input facilitates to connect with any readers.
• Cost saving
For more feel free to reach out to us in case any clarification is required.
Resilient Technologies
M. No. - +91 9810995267
Visit on: www.resilienttec.com
Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001
Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
QuadXs2c is one of the most successful controller presently available in the market. Client includes large corporates like firstsource, Ranbaxy, Myntra and many more. This is one of the most flexible hard ware with 4 completely configurable outputs and 8 General purpose inputs. Further integration with fire is possible very smoothly. It supports weigand / HID based readers Features: 4 door / 8 reader Controller Supports access control of up to 4 doors in all respect including 4 entry readers, 4 exit readers, 4 locks, 4 exit switches etc Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Network interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCR/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware Facility to onsite upgrade the firmware over Ethernet interlace so that any customisation or new version can be easily upgraded without any need of removing the device or physical presence of the engineer near the device Protected Enclosures Both controller & power supply unit are protected with suitable housing so electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking Facility of door interlocking is available. The system allows creating a group of doors such that access to a door .thin the group is allowed only when all the other doors are in closed condition. Excellent Price Performance Ratio With a lower price to performance ratio ROI is automatically enhanced, the factor contributing to higher ROI is not only very competitive pricing but also higher accuracy rate offered by the product Fully configurable GPI and GPO Optically Isolated inputs for 4 Door Sensor, 4 Exit Switch & 8 General purpose digital inputs along with 4 General purpose relay outputs. These are fully configurable. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Two Door / Four Reader Controller TwinXs 3S is a versatile access control panel and supports 2 doors and 4 access readers. The controller can be configured as standalone / Master or Slave. The controller supports host of other rule based features apart from global anti pass back. High Speed Controller with Large Memory The controller has high speed 32 bit processor and has a large storage of 4GB. It has a capacity to store 200000 card holder database and last 500000 event buffer. The high speed processor facilitates access decisions in milliseconds. Local Programming The controller has LCD display and a 12 key keypad. This interface allows use to even program the controller without attaching it to the host computer. Also it facilitates on field diagnostics. Compact Design The controller size is very compact with respect to the number of interfaces. Also it has field pluggable connectors which helps in ease of wiring and termination. The controller is housed in powder coated MS cabinet along with rugged 5 amp power supply. All the reader ports are current limited there by ensuring that the controller doesn’t go down even when any of the port is sorted or malfunctioning. Data Communication and Protocols The controller supports popular communication interfaces viz 10/100 mbps ethernet, CAN and RS485. Master/Slave configuration can be implemented over any of these interfaces. In addition, it supports multiple protocols such as HTTP, SNMP, SMTP, FTP, SSL & NTP. It also supports MODBUS protocol over ethernet for integration. Fully Programmable I/O’s The controller has 8 optically isolated digital inputs out of which 4 are general purpose fully programmable, 2 dedicated for door sensor inputs, and 2 dedicated for egress switch inputs. Also the controller has 4 general purpose outputs apart from lock control outputs. The general purpose outputs are available as potential free contacts. Configurable Reader Interface The reader interface is configurable. The controller also supports legacy clock/ data interface in addition to more popular weigand interface. The weigand interface is configurable from 24 to 64 bits. Field Upgradable Software Facility to onsite update device software through ethernet interface. The product updates can easily be applied without the need of removing device and sending it back to the service center. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
TwinXs2c is one of the most successful controller presently available in the market. Client includes large corporates like firstsource, Ranbaxy, Myntra and many more. This is one of the most flexible hard ware with 4 completely configurable outputs and 8 General purpose inputs. Further integration with fire is possible very smoothly. It supports weigand / HID based readers Features: 2 door / 4 reader Controller Supports access control of up to 2 doors in all respect including 2 entry readers, 2 exit readers, 2 locks, 2 exit switches etc. Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Network interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCR/IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware Facility to onsite upgrade the firmware over Ethernet interlace so that any customisation or new version can be easily upgraded without any need of removing the device or physical presence of the engineer near the device Protected Enclosures Both controller & power supply unit are protected with suitable housing so electronic circuit boards are not exposed to cause any accidental damage. Anti Pass Back Door wise antipassback. Entry to the particular door is allowed only when the employee has exited through the same door. Door Interlocking Facility of door interlocking is available. The system allows creating a group of doors such that access to a door .thin the group is allowed only when all the other doors are in closed condition. Excellent Price Performance Ratio With a lower price to performance ratio ROI is automatically enhanced, the factor contributing to higher ROI is not only very competitive pricing but also higher accuracy rate offered by the product Fully configurable GPI and GPO Optically Isolated inputs for 4 Door Sensor, 4 Exit Switch & 8 General purpose digital inputs along with 4 General purpose relay outputs. These are fully configurable. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
Ouzim BioEngine2 Biometric Fingerprint Access Control for security entrance solution Model: BioEngine2 Supports multiple authentication multifunction: fingerprint, passcode and cards. 1. 3,000 fingerprints +3,000 cards +3,000 passcode + 200,000 records 2. Support Mifare card 13.56 MHz +ID card 125KHZ 3. 360-degree rotation identification, high sensitive to identify. No need film cover on the sensor 4.
Supplier: CCTV, biometrics, access control, turnstiles, elevator controller, ERP software, fire alarm systems, home automation, LPG leakage system
P20 Proximity reader is indigenously developed high performance reader to read Mifare read only card. It provides a consistent read range of 4-5cm in most of the conditions. The reader is particularly suited to access control applications. The same basic unit can be configured to most common output interface formats, including Weigand, Megstripe and Rs-232 serial ASCII. Features: 13.56MHz Mifare reader that meets ISO 14443A standards Suitable four door access control applications. It can be easily mounted on walls and doors Reads both 32 bit Mifare CSN and Sector Advance key management for high security Compact and high esthetics Dual LED indications Weigand interface, compatible with most of the existing access control systems. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085
CMFP1000 is a canteen recording system. It can be connected to a printer for getting coupons / slips of the canteen consumption. This system can be prepaid / postpaid. It is a field proven product being used by many clients for long period incorporating industry?s most advanced and powerful finger print reader. It boasts of a robust metal enclosure for rugged industrial usages. It comes up with various options to suit varied requirements. It has been seamlessly integrated with Mifare & RFID technologies. This is most celebrated product of the biometric range offered by us Aluminium Die Cast Enclosure Rugged aluminium die cast housing is meant to provide extra strength to the device particularly for rough industrial usage. This is particularly useful in case of attendance of workers where there is high possibility of machine being handled with less care Keypad 12 Keys Membrane keypad for local programming. Here the employee can be added and other function can be used. Various canteens items can be selected through this keypad. Rugged Fingerprint Algorithm Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verification results. Superior Verification Technique Quality score display before registration helps in identifying the ideal finger for routine verification whereas auto finger update helps in keeping the track of finger changes over the period thus adequately taking care of dry, wet & swollen fingers. Inbuilt TCP/IP Network Interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCP/ IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgradable Firmware Facility to onsite upgrade the firmware over Ethernet interface so that any customisation or new version can be easily upgraded without any need of removing the device. Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Fingerprint template can be stored on a smart card with HID iClass/Mifare technology to facilitate data portability & unlimited users without being dependent on the device template capacity. For more feel free to reach out to us in case any clarification is required.
FingerXs/FP1000 is a standalone finger print recognition based access control and attendance recording system. It is a field proven product being used by many clients for more than 10 years incorporating industry most advanced and powerful finger print reader. It boasts of a robust metal enclosure for rugged industrial usages. It comes up with various options to suit varied requirements. It has been seamlessly integrated with Mifare & RFID technologies. This is most celebrated product of the biometric range offered by us. Features: Aluminium Die Cast Enclosure Rugged aluminium die cast housing is meant to provide extra strength to the device particularly for rough industrial usage. This is particularly useful in case of attendance of workers where there is high possibility of machine being handled with less care Keypad 12 Keys Membrane keypad for local programming. Here the employee can be added and other function can be used Rugged Fingerprint Algorithm Equipped with most reliable fingerprint matching algorithm to ensure unrivaled accuracy with best verification results. Superior Verification Technique Quality score display before registration helps in identifying the ideal finger for routine verification whereas auto finger update helps in keeping the track of finger changes over the period thus adequately taking care of dry, wet & swollen fingers. Inbuilt TCP/IP Network Interface Leveraging on the merits of IP based systems, it can easily be hooked up on the existing TCP/ IP network. Thus the data can be transferred instantaneously in real time mode to a centralized server. Field Upgrada b le Firmware Facility to onsite upgrade the firmware over Ethernet interface so that any customisation or new version can be easily upgraded without any need of removing the device. Multiple RFID Technologies Supports all latest RFID technologies with inbuilt EM reader and option of having Mifare/HID iClass/ HID Pros. Fingerprint template can be stored on a smart card with HID iClass/Mifare technology to facilitate data portability & unlimited users without being dependent on the device template capacity. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon ? 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi ? 110085
P20 Proximity reader is indigenously developed high performance reader to read EM REID read only card. It provides a consistent read range of 8-10cm in most of the conditions. The reader is particularly suited to access control applications. The same basic unit can be configured to most common output interface formats, including Weigand, Megstripe and Rs-232 serial ASCII. Features: • High aesthetic and appealing looks • User selectable interface e.g. Wiegand, Clock/Data, Rs232 • East firmware upgrade through PC • Green LED and Buzzer can be control by the related control pins. • Output signal for tampering • Card read indication by LED and Buzzer. For more feel free to reach out to us in case any clarification is required. Resilient Technologies M. No. - +91 9810995267 Visit on: www.resilienttec.com Corporate office: 578 | UdyogVihar Phase V | Gurgaon – 122001 Branch office: 465 | Pocket E-16 | Rohini | New Delhi – 110085