Characteristics 1.Assay of Oxidizable elements and microelements can be adjusted and controlled by using cored wire. It can help to improve the alloy yield,reduce smelting cost, shorten smelting time and control composition precisely. 2.It can purify the molten steel and partly change steel inclusion morphology and properties, improving molten steel quality and casting state. 3.The equipment for cored wire injection is simpleï¼?leading to small occupation area.
Hf+Zr 99.95% Zr 0.8% max.
Niobium 10% Hfanium 1% Titanium alloy as per ASTM standard
Introduction Pure Zinc & Zn/5Al are excellent material choices for corrosion protection in both atmospheric and marine environments. Using either the electric arc spray or combustion wire process, wire coatings of these materials act as sacrificial anodes, galvanically protecting iron or steel substrates.Decades of field work using these coatings has clearly demonstrated that they are far more effective and longerlasting than hot dip galvanizing. Coatings of ZnAl often have better corrosion resistance than either pure zinc or aluminum, by combining the advantages of both materials. This is particularly true in areas where crevices exist and residual moisture and contamination is present, and in areas where the coating has been scratched or scraped, resulting in coating voids and exposed substrate. Using the electric arc spray process, coatings of these materials are often used in the electronics industry for EMI and RF shielding, or as conductive coatings on capacitors. Typical Uses and Applications Atmospheric and immersion corrosion protection on large steel or iron structures such as bridges, roadway barriers, posts and poles, offshore structures and marine structures. Atmospheric corrosion protection on steel or iron components such as tanks and gas bottles EMI and RF shielding on plastic components (electric arc spray only) Electrical conductance on components such as the Conductive areas on insulators and capacitor end caps Product Details Chemical composition: Type Chemical composition Zn Al Others Zn 99.9+ Balance 0.1 Zn 15Al Balance 15 Specifications Grade AWS Zn C2.25/C2.25M W-Zn-1 Physical Properties Grade Density Rockwell Hardness Zn 7.14 g/cm3 ZnAl 7.18 g/cm3 Typical Deposit Characteristics: Grade Typical Hardness Bond Strength Deposit Rate Deposit Efficiency Machilityineab Zn HRB 20 - 30 6.9 - 15.0 Mpa 24 lbs /hr/100A 0.7 Good Zn 5Al HRB 40 -45 20.7 - 24.1 Mpa / / Good Standard Sizes & Packing: Diameter Packing Wire Weight 1/16 (1.6mm) D 300 Spool 15kg((33 lb)/spool Other sizes can produced based on customers' requirement.
Specification Place of origin:hebei, china (mainland) Brand name:ac Model number:ac-rb17 Material:hot dipped galvanized\stainless steel wire Surface treatment:galvanized Type:razor barbed wire coil Razor type:cross razor wire\single razor wire Product name:razor wire Material:galvanized wire or stainless steel wire Razor wire blade ty p e :bto- 10, 22, 0;c bt-6 0, 65, etc Razor wire blade thickness: 0.35mm-0.6mm Razor wire clips: 3clips or 5 clips or without clips Razor wire outside diameter:450mm-960mm Razor wire standard length per coil:10-18m Razor wire qc:iso9001:2008
Calcium Metal Lump Ca: 98.5%min with size 50-200mm,90%min Calcium Metal Granular Ca: 98%min, or 98.5%min size: 0-2mm,0-3mm,0.2-2mm,0.2-3mm,90%min Calcium Metal Turnings Ca: 98%min Width: 10mm, Length: 20mm, Thickness: 1mm Packing for above: steel drum with wrapped , filled in Argon gas inside.
Pure zinc wire The surface of the zinc wire is smooth and bright, no broken wires, no greasy dirty and burrs, no scratches and scars, no jam in the process of use Product purity: zinc content more than 99.995% Diameter: 1.0mm-4.0mm Package20--5kg/Bundle 15kg-20kg/Shaft 50kg-250kg/Barrel MaterialAdopt 0# distillation zinc ingot produced by Hulo Island Zinc Co., LTD, zinc content more than 99.995%. The material used is strictly stick to national standards GB/470-2008 Characters: 1.The size and shape of spray will not be affected. You can spray on the whole surface, and also you can spray the limited surface which is convenient and economical to the parts of large conponents. 2.The parent material will not change. Because when spraying, the parent material will become small due to low temperature. 3.The thick of coating can be changed in large range from several microns to several millimeters 4.It can be sprayed to form shapes. Hot spraying technology can be used not only to form shape in the surface, but also to manufacture mechanical parts, that is spraying molding products. Transportation storage It is forbidden to bring with acid, alkali, salt corrosion of zinc by packaging and transportation shipment, and it should be stored in dry, ventilated, non-corrosion material warehouse and keep out of rain. Applications The thermal spraying wire is used in a variety of applications, such as: 1.High-temperature oxidation protection used, for example, to resist gases in boiler atmospheres 2.Coatings to resist heat and prevent scaling of conventional low alloy steels 3.Bond coats for improving the adhesion of top coatings 4.Coatings on moulds in the glass industry It is used in the flame spraying, arc spraying, supersonic plasma spraying, the ordinary plasma spraying.
NiAl 95/5 alloy is a nickel aluminium alloy characterized by dense coating,high temperature oxidation resistance, heat shock resistance and scratch resistance.This wire has stable chemical composition, low oxgen and high bonding strength. Typical applications for NiAl 95/5 are widely used in arc and flange flame spray systems, Coatings to resist heat and prevent scaling of conventional low alloy steels,Bond coats for improving the adhesion of top coatings,Coatings on moulds in the glass industry. Common name: NiAl 95-5, Nickel Aluminum 95/5 N9 Ni95Al5 95/5 Nickel Aluminum F-80NA Nickel Aluminium 95/5
TANKII 45CT is a nickel chrome titanium wire specifically designed for arc spraying. It produces dense, well-bonded coatings with excellent corrosion resistance and good wear resistance. It is highly resistant to sulfur and vanadium atmospheres up to 1825°F. It has proven to be particularly effective as a protective arc spray coating for boiler tubes in black liquor recovery boilers and coal fired utility boilers.
TANKII Cr13 is a 420 stainless steel wire, specifically designed for arc spray processes. TANKII Cr13 forms a dense, well bonded coating, with excellent wear resistance and good corrosion resistance. It is widely used for machine elements repair, dimensional restoration, and wear resistant application. TANKII Cr13 s low shrink rate characteristics allows for increased coating thickness on parts requiring heavier coatings.
We are dealing with thermal spray wires such as nial95/5 wires for bond coats.
We are dealing with thermal spray wires such as nicrti wire for boiler. And our standard packing is 15 kgs per spool. Normally we have them in stock.
We are dealing with thermal spray wires such as stainless steel 420 wire. And we have 3 tons in stock with size 1.6mm. And our standard packing is 15 kgs per spool.
We are dealing with thermal spray wire such as cual8 wire. And normally we have them in stock. Our standard packing is 15 kgs per spool.
We are dealing with thermal spray wire such as babbit wire used for turbine. And now normally we have 1.6mm babbitt wire in stock, and our standard packing is 15 kgs per spool.
Because the mesh belt is zigzag design,with the characteristics of good water permeability, air permeability and non-revealed sludge, acid-resistance, alkali-resistance, heat resistance under 180 degrees. Sludge and mesh strip peel quickly, not easy to stick mud, a large number of mud, easy to clean, fast and convenient connection, long life of the mesh. This is designed for sludge dewatering products.
Chemical products metal products like copper wire scrap, copper cathode, tungsten rod, aluminum plate, nickel alloy, silicon, copper powder, tungsten powder, wire mesh, zinc ingot.Clearing agent, transportation, and shipping etc.
For hexagonal metal wires with galvanized layer, use metal wires with a wire diameter of 0.3mm to 2.0mm. If it is a PVC-coated metal wire woven twisted mesh, use PVC with an outer diameter of 0.8mm to 2.6mm. (metal) wire. Twist it into a hexagonal shape, and the lines on the edge of the outer frame can be made into single-sided, double-sided, movable edge wires. English name hexagonal wire netting hexagonal wire mesh Weaving method: forward twist, forward and reverse twist (reverse twist). characteristic: (1) Easy to use, just tile the mesh into the wall or building cement to use (2) Construction is simple and no special skills are required (3) Strong ability to withstand natural damage, corrosion and harsh weather effects (4) It can withstand a wide range of deformation without collapse. Acts as fixed thermal insulation (5) Excellent process foundation ensures uniformity of coating thickness and stronger corrosion resistance (6) Save transportation costs: it can be reduced into a small roll and wrapped in moisture-proof paper, taking up very little space. (7) Heavy-duty twisted mesh is woven with high-quality low-carbon steel wires, galvanized large wires, the tensile strength of the steel wires is not less than 38kg/m2, the diameter of the steel wires can reach 2.0mm-3.2mm, and the surface of the steel wires is usually hot-plated Zinc protection, the thickness of the galvanized protective layer can be made according to customer requirements, and the maximum galvanizing amount can reach 300g/m2. (8) Galvanized wire plastic-coated twisted mesh is to cover the surface of galvanized iron wire with a PVC protective layer and then weave it into various specifications of twisted mesh. This PVC protective layer will greatly increase the service life of the net, and through the selection of different colors, it can blend with the surrounding natural environment.
For hexagonal metal wires with galvanized layer, use metal wires with a wire diameter of 0.3mm to 2.0mm. If it is a PVC-coated metal wire woven twisted mesh, use PVC with an outer diameter of 0.8mm to 2.6mm. (metal) wire. Twist it into a hexagonal shape, and the lines on the edge of the outer frame can be made into single-sided, double-sided, movable edge wires. English name hexagonal wire netting hexagonal wire mesh Weaving method: forward twist, forward and reverse twist (reverse twist). characteristic: (1) Easy to use, just tile the mesh into the wall or building cement to use (2) Construction is simple and no special skills are required (3) Strong ability to withstand natural damage, corrosion and harsh weather effects (4) It can withstand a wide range of deformation without collapse. Acts as fixed thermal insulation (5) Excellent process foundation ensures uniformity of coating thickness and stronger corrosion resistance (6) Save transportation costs: it can be reduced into a small roll and wrapped in moisture-proof paper, taking up very little space. (7) Heavy-duty twisted mesh is woven with high-quality low-carbon steel wires, galvanized large wires, the tensile strength of the steel wires is not less than 38kg/m2, the diameter of the steel wires can reach 2.0mm-3.2mm, and the surface of the steel wires is usually hot-plated Zinc protection, the thickness of the galvanized protective layer can be made according to customer requirements, and the maximum galvanizing amount can reach 300g/m2. (8) Galvanized wire plastic-coated twisted mesh is to cover the surface of galvanized iron wire with a PVC protective layer and then weave it into various specifications of twisted mesh. This PVC protective layer will greatly increase the service life of the net, and through the selection of different colors, it can blend with the surrounding natural environment.
Tyre bead wire is a high quality carbon metal. It is incorporated in the structure of the tyre to withstand bumps, heat and other hazardous conditions. radial tyre bead wire is 1.6 mm and nylon tyre bead wire is 1.10mm. Therefor, the wire obtained from end of life tyres is also of high quality matieral and resuing it can be a highly lucrative for the businesses as well as the environment. Scrap Bead Wire is used in converting to shot blasting, high tension springs, wire mesh, wire baskets, nails, cutting tools. Since this is extracted from tyres it is available at a very reasonable rates. A Scrap truck or Bus Tyre consists of 20-25% of high quality steel in it. The metal bead wire is obtained when the waste tyre is put into the shredding machines. It is very important to derive the bead wire in one single piece. The wire can easily be oxidised so protecting it from different atmospheric agents is important. So to meet our clients' expectations, we have set strict standards and quality control techniques. )
