Shijiazhuang Canchun Metal Products

Zinc aluminum alloy wire The raw materials used in all 0# zinc distillation zinc ingot quality, high purity zinc, the zinc content of more than 99.995%, the strict implementation of national standard gb/t470-2008;the raw material aluminum ingot all uses the high-quality aluminum ingot, the aluminum ingot purity is high, the aluminum content above 99.8%, strictly carries out the national standard, the remelting uses the aluminum ingot gb/t1196 - 2008 Characters 1. Zinc aluminum alloy coatings have similar stability with spraying aluminum coatings and the electrochemical protection as well as spraying zinc coating, zinc aluminum alloy coating is an ideal anticorrosion protective coating of sea water. 2. Compared with the zinc wire and pure aluminum wire, it's coating has coherence, the resistance to wear and corrosion resistivity is better as well as the construction of superior performance. The zinc aluminum alloy wire makes the sacrifice anode and sprays coating in the steel and iron component surface layerand it make the component service life lengthen 5-10 times Specification Composition: zn/al 85/15 Diameter:2.0-10mm Package:20-150kg/bundle , 20kg/spool , 50-250kg/barrel(drum) Application Zinc aluminum alloy wire is widely applied to thermal spraying anticorrosion, container, bridge, head frame, storage tank, electric iron tower, poles and towers, capacitor, metal bracket, nodular cast iron pipe, traffic equipments, etc.

Pure zinc wire The surface of the zinc wire is smooth and bright, no broken wires, no greasy dirty and burrs, no scratches and scars, no jam in the process of use Product purity: zinc content more than 99.995% Diameter: 1.0mm-4.0mm Package20--5kg/bundle 15kg-20kg/shaft 50kg-250kg/barrel Materialadopt 0# distillation zinc ingot produced by hulo island zinc co., ltd, zinc content more than 99.995%. The material used is strictly stick to national standards gb/470-2008 Characters: 1.The size and shape of spray will not be affected. You can spray on the whole surface, and also you can spray the limited surface which is convenient and economical to the parts of large conponents. 2.The parent material will not change. Because when spraying, the parent material will become small due to low temperature. 3.The thick of coating can be changed in large range from several microns to several millimeters 4.It can be sprayed to form shapes. Hot spraying technology can be used not only to form shape in the surface, but also to manufacture mechanical parts, that is spraying molding products. Transportation storageit is forbidden to bring with acid, alkali, salt corrosion of zinc by packaging and transportation shipment, and it should be stored in dry, ventilated, non-corrosion material warehouse and keep out of rain. Applications The thermal spraying wire is used in a variety of applications, such as: 1.High-temperature oxidation protection used, for example, to resist gases in boiler atmospheres 2.Coatings to resist heat and prevent scaling of conventional low alloy steels 3.Bond coats for improving the adhesion of top coatings 4.Coatings on moulds in the glass industry It is used in the flame spraying, arc spraying, supersonic plasma spraying, the ordinary plasma spraying.

Pure zinc wire The surface of the zinc wire is smooth and bright, no broken wires, no greasy dirty and burrs, no scratches and scars, no jam in the process of use Product purity: zinc content more than 99.995% Diameter: 1.0mm-4.0mm Package20--5kg/Bundle 15kg-20kg/Shaft 50kg-250kg/Barrel MaterialAdopt 0# distillation zinc ingot produced by Hulo Island Zinc Co., LTD, zinc content more than 99.995%. The material used is strictly stick to national standards GB/470-2008 Characters: 1.The size and shape of spray will not be affected. You can spray on the whole surface, and also you can spray the limited surface which is convenient and economical to the parts of large conponents. 2.The parent material will not change. Because when spraying, the parent material will become small due to low temperature. 3.The thick of coating can be changed in large range from several microns to several millimeters 4.It can be sprayed to form shapes. Hot spraying technology can be used not only to form shape in the surface, but also to manufacture mechanical parts, that is spraying molding products. Transportation storage It is forbidden to bring with acid, alkali, salt corrosion of zinc by packaging and transportation shipment, and it should be stored in dry, ventilated, non-corrosion material warehouse and keep out of rain. Applications The thermal spraying wire is used in a variety of applications, such as: 1.High-temperature oxidation protection used, for example, to resist gases in boiler atmospheres 2.Coatings to resist heat and prevent scaling of conventional low alloy steels 3.Bond coats for improving the adhesion of top coatings 4.Coatings on moulds in the glass industry It is used in the flame spraying, arc spraying, supersonic plasma spraying, the ordinary plasma spraying.

Aluminum wire (Pure Aluminum Wire, Aluminum Line and Spray Finishing Aluminum Wire) ,The surface of aluminum wire is smooth and bright; no break of wire exists; single wire has no greasy dirt, burr, scratch or scar; there is no block of device in application. The product adopts high quality aluminum ingot, no other substances enter the process from raw material (aluminum ingot) input to strip output, and the product is not exposed to other metal. The detection adopts DF-100 type direct-reading spectrometer, inductively coupled plasma atomic emission spectrum and other high-end testing instruments. Strict check and detection are conducted in the whole working procedures including raw material-wire output-big drawing-middle drawing-water tank-baling-storage. Not a tiny detail is neglected. Hence, the long-term stability of product performance is ensured. The content of each batch of aluminum wire is guaranteed to be above 99.7%. Specifications Composition : Al 99.7% Diameter:1.2-4.75mm Package : 20-150kg/bundle , 7kg/Spool Characters 1. The size and shape of spraying are insusceptible. Spraying can be conducted on the whole surface, or on a large defined surface, which is a convenient and economical method in coating the partial surface of a large unit. 2. The parent material doesn t change. For the heated temperature on parent material is low during spraying, the work piece only distorts slightly. 3. The thickness of coating varies in a large range, from several microns to several millimeters. 4. Spraying moulding is available. Thermal spraying technology can not only form a coating on the surface of material, but also be used to manufacture machinery parts, namely, spraying molding products. Transportation & Storage: Wrap page and means of transportation with acid, alkali or salt that may corrode aluminum are forbidden. Aluminum segment should be stored in a dry and ventilated storeroom which is free of corrosive substance and be protected from rain. Application Aluminum wire is widely applied to thermal spraying anticorrosion, container, bridge, head frame, storage tank, electric iron tower, poles and towers, capacitor, metal bracket, nodular cast iron pipe, traffic equipments, etc.

Introduction: Grinding rods can be customized according to customer's requirements Automatic production line of grinding rods, which can be quenched and tempered automatically. It is mainly used for metallurgical and mining, cement plant, thermal power, chemical industry, etc. Features High hardness, range is 45~55hrc Low bending, less than 1.5mm/m Dense microstructure , bainite +pearlite+carbide Low breakage rate, more than 15000 times/ 3.5m Low unit consumption, 40% reduction compared to unprocessed round steel -

Introduction Casting steel ball diameter from 20-150mm with high hardness, low wear, Low broken rate, strong heat resistant and corrosion resistance, chromium content From 1%-28%, hrc45-63, .Detailed specifications can be customized according To customer demand. It is particularly used in cement industry working in the grinder with high temperature, high crushing and strong abrasion . The grinding ball with chromium content 1% - 3% and hardness hrc >=45 called Low chromium alloy cast ball. Low chromium ball is produced by the intermediate frequency electric furnace smelting, metal mold or sand casting . Features Good toughness, low abrasion rate, low bro ken rate , low chromium ball hardness can reach 45-55hrc -

1.Forged grinding balls Our products range from 20mm to 150mm, 1 inch to 6 inch, and we can also offer all size of products according to clients demand. 2.Features: 1) forged grinding ball has high hardness: surface hardness to 58-65hrc, volume hardness of 57-64hrc 2) impact toughness high: impact toughness more than 12j / cm2. 3) broken rate is low: the actual broken rate is not higher than 0.5%. 4) loss of forged grinding ball round rate is low. 5) dropping test in 8m high tester for more than 20, 000 times. -

Grinding cylpebs specification Ball diameter(mm) 10 12.7 15 17 20 25 30 40 50 60 70 80 90 100 110 120 125 130 Chemical coposition Zqcr2 C Si Mn Cr Mo P S 2.2-3.5 0.3-1.4 0.2-1.5 0.3-3.0 1.0 0.15 0.15 Properties and microstructure Designation Hrc Impact value(j/cm2) Microstructure Times of falling balls Zqcr2 46 1.5 P+c 15000 -