CuCo1Ni1Be--CW103C (DIN 2.1285) Cobalt Nickel Beryllium Copper Alloy contains approximately 1% Cobalt, 1% Nickel and 0.5% Beryllium. After hot forging and heat treatment processes this material gains considerably hardness, electrical and thermal conductivity as well. It is possible to have different combinations of electrical conductivity and hardness by changing the heat treatment conditions;CuCo1Ni1Be also Offers good strength and hardness characteristics coupled with conductivity in the range of 45-60 percent of copper with ultimate tensile and hardness properties approaching 140 ksi and RB 100 respectively, all of its properties are quite the same as CuCo2Be-C17500 and CuNi2Be-C17510.
International Specification:
Rods/Bars/Tubes: ASTM B441, SAE J461,463; RWMA Class 3
Sheets: ASTM B534
Wires: ASTM B441
Plates: ASTM B534, SAE J461,463; RWMA Class 3
European Standards: CuCo1Ni1Be, DIN 2.1285; CW103C to EN
Note:
ASTM: American Society for Testing and Materials
SAE: Society of Automotive Engineers
AMS: Aerospace Materials Specification (Published by SAE)
RWMA: Resistance Welder Manufacturers' Association
Note: Unless otherwise specified, material will be produced to ASTM.
CuCrNi2Si ¿C UNS.C18000 Copper Chromium Nickel Silicon Alloys, which also called Beryllium Free Copper alloy, meets the mechanical requirements of RWMA Class 3 Copper, is a very hard heat treatable copper based alloy with an economical higher strength and high conductivity, and C18000 Alloys is utilized when a combination of very good mechanical strength along with moderate electrical and thermal electrical conductivity are required. Furthermore, C18000 alloy is an excellent substitute for copper beryllium alloys C17500 and C17510 in terms of many applications.
International Specification:
Rods/Bars/Plates/Sheets: UNS.C18000, CDA180, RWMA Class 3
European Standards: CuCrNi2Si, DIN 2.0855, CW111C to EN
Note:
ASTM: American Society for Testing and Materials
RWMA: Resistance Welder Manufacturers' Association
Note: Unless otherwise specified, material will be produced to DIN & RWMA.
Cube2--c17200 (cda 172) beryllium copper is the most commonly utilized copper beryllium alloy and is notable for its highest strength and hardness compared to commercial copper alloys. C17200 alloy contains appr. 2% of beryllium and achieves its ultimate tensile strength can exceed 200 ksi, while the hardness approaches rockwell c45. Meanwhile, the electrical conductivity is a minimum of 22% iacs in the fully aged condition.C17200 also exhibits exceptional resistance to stress relaxation at elevated temperatures.
Available sizes:
Custom diameter & sizes, random mill lengths
International specification: ú¿¦·+O¦µ+¦ú¬
Rods/bars/tubes: astm b196, 251, 463; sae j461, 463; ams 4533, 4534, 4535; ams4650, 4651;
Rwma class 4
Strips:astm b194, ams4530, 4532; sae j461, 463
Sheets: astm b194
Wires:astm b197, ams4725, sae j461, 463
Plates:astm b194, sae j461, 463; ams4530, 4533, 4534, ams4650, 4651; rwma class 4.
European standards: cube2, din 2.1247, cw101c to en
Note:
Astm: american society for testing and materials
Sae: society of automotive engineers
Ams: aerospace materials specification (published by sae)
Rwma: resistance welder manufacturers' association
Note: unless otherwise specified, material will be produced to astm.
We confirm with full Corporate authority that it is out intention to sell the commodity HMS1 & 2 as per the terms and condition given below :-
1. Commodity : HMS 1 AND 2
2. Specification : ) HMS 1 AND 2 steel shall be considered free of alloys when the residual alloying elements do not exceed the following percentages: percent
Calcium metal series including: Calcium ingot, Calcium lump, Calcium turning, Calcium granular
Chemical composition: Ca: 99.0%min and Ca: 98.5%min
Calcium lumps: 30-100mm, 30-150mm,30-200mm.
Calcium granulars: 0-2mm, 0-3mmú¼0-6mm
Calcium turning: 30-80mm (Length), 6-8mm (Width), 0.7-3.6mm (Thickness)
Or as per customers special and detailed specifications
Application: in Metallurgy for steel-making, special alloy smelting, battery line, medicine adding, etc.
Ca-Mg alloy
Specification: Ca: 30%, Mg:70%
Size: 30-100mm (Irregular lumps) or as per clients requirements.
Application: Additive of middle alloys for metal instrument founding mills.
Magnesium metal series including: Magnesium ingot, Magnesium granular, Magnesium powder, passivation Magnesium granular.
Chemical composition: Mg;99.90%min, Mg;99.95%min ,Mg;99.99%min
Magnesium Ingots : 15kg/pc 7.5kg/pc 1kg/pc
Magnesium granular, Magnesium powder: 2mm-0.015mm
Packing: 1000 kg per woven bag or up to customer's requirement.
Application: metallurgical casting, Military industry and metal instrument manufacture, in desulfuration and producing of magnesium alloy, also can be used in chemical industry.
Produce as customers requests.
Xundake procures a variety of quality machinery parts through an extended network of suppliers. Contact us to know more about the business opportunities in China.
Xundake procures a variety of quality machinery parts through an extended network of suppliers. Contact us to know more about the business opportunities in China.
We can supply various kinds of magnesium related products .Such as magnesium ingot, magnesium alloy, magnesium granular(powder), etc.
Magnesium ingot as below:(note:customers special request available!)
Magnesium ingot
Mg:99.9%min.
Al: 0.02%max.
Si 0.02%max.
Mn 0.02%max.
Magnesium ingot size: 7.5kg+/- 0.5kg
High purity magnesium:
Mg:99.95%min. Al: 0.0040%max. Fe 0.0045%max. Si 0.0070%max.
Ni 0.0010%max.
Mn 0.0070%max.
Cu 0.0030%max.
Magnesium ingot size: 7.5kg+/- 0.5kg
Mg:99.99%min.
Al: 0.0020%max. Fe 0.0045%max. Si 0.0020%max.
Ni 0.0010%max.
Mn 0.0020%max.
Cu 0.0020%max.
Magnesium ingot size: 7.5kg+/- 0.5kg
Magnesium alloys such as :
Az91d, az91hp , az63 , za10, am60, am50, am20, ze41a and so on with the standard of gb/t5153-2003, gb/t19073-2003 and astmb94-92.
Magnesium ingot size: 7.5kg+/- 0.5kg
Packed on pallets with plastic covering and steel tape to tighten
