We are associated with Mines in South America and can deliver ONLY FOB a maximum of 50,000 MT per loading due to Port restrictions. If interested do email me or Whatsapp
Lump sulfur, also known as granular or rock sulfur, is typically characterized by a purity of 99.80% or higher, with a maximum ash content of 0.05%.
It should also have a limited acidity (H2SO4) of 0.02% or 0.03% and minimal moisture content (0.5% or 0.2%).
More detailed breakdown of lump sulfur specifications:
Purity:
Dry Basis: 99.80% minimum purity is a common specification.
Other Standards: Some standards like Refinery Specifications, may specify a purity of 99.98%.
Impurities:
Ash Content: A maximum ash content of 0.05% is a typical requirement.
Acidity: A maximum acidity (H2SO4) of 0.02% or 0.03% is common.
Organic Substances: Some specifications limit organic substances to 0.01% or 0.03% maximum.
Moisture: A maximum moisture content of 0.5% or 0.2% is generally specified.
Mechanical Impurities: Some specifications require the absence of mechanical impurities like paper, wood, or sand.
Other Impurities: Some standards specify limits for arsenic, selenium, tellurium, and lead impurities.
Color and Appearance:
Color: Bright yellow is the typical color specification.
Other Considerations:
Test Methods:
Specifications often include test methods, such as ASTM D-4239, ASTM D-1509, ASTM D-1613, and ASTM D-2790, for determining the various parameters.
Bulk Density:
Granular sulfur has a bulk density of around 70 lb/cu ft (1121.29 kg/cu m).
Solubility:
Sulfur is insoluble in water, partially soluble in acetone, and slightly soluble in diethyl ether and alcohol.
Keep away from heat, hot surfaces, Sparks, Open flames and other ignition sources. No smoking. Proper
grounding procedures to avoid static electricity should be followed. Prevent dust accumulation (to minimize
explosion hazard). Avoid generating dust.
Other Hazards:
It contains a small amount of Hydrogen Sulfide. Hydrogen sulfide is a fatal and highly flammable gas with a
rotten egg odor that quickly causes odor fatigue. Heating of this product and storage under elevated
temperatures or over long periods of time may release higher amounts of Hydrogen Sulfide. Hydrogen
Sulfide is also an asphyxiant. Exposure may aggravate preâ??existing eye, skin, or respiratory conditions.
Storage:
(1) Prevent from moisture absorption, keep away from heat, keep in air well â?? ventilated area.
(2) Do not contact with acids and alkaline substance, protect from dust.
(3) Ensure bags are kept in sealed and in good condition.
Packing:
The packing is in 50/Kg. bags, Jumbo Bag 1/MT or in Bulk.
Spcification of Sulfur:
Color: Bright yellow when solid (No dark particles visible)
Purity: 99.8% by weight minimum, dry basis. Sulfur Content: 10ppm by weight, maximum (0.01%)
Moisture Content: 0.50% by weight maximum
Ash: 300ppm by weight, maximum (0.03%)
Organic matter: 500ppm by weight, maximum (0.05%)
Size: 2mm â?? 6mm
Bulk Density: Minimum 1040 Kg/m3 (loose)
Bulk Density: Minimum 1200 Kh/m3 (packed)
Acidity as H2SO4: 50ppm by weight, maximum (0.005%)
We intercontinenal minerals SDN BHD ,Malaysia introduce ourself as one of the leading HMS-1&2,USED RAILS, Ship Breaking Suppliers in Malaysia.We are in this Export and Import business from 2000 onwards.Our CEO is having vast experience in this field and done lot of projects in India and Malaysia.
We have HMS-1&2,USED RAILS few in Stocks and Mostly from our Channel Partners, in USA ,Europe,Russia,and Asian countries (Stocks each 400,000 Tons) in thier Stock Yards.
We came to understand that you require lot of HMS and Used Rails.If you are interested Kindly send your detailed enquiry to quote our best price.We will provide you Proofe Of Product after receiving your LOI and BCL
Silicon steel
1.0 scope
1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide
Low core loss and high permeability needed for more efficient and economical electrical
Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used
For transformer cores and large generators.
2.0application
2.1 the cgro is used regularly for cores in transformers.
3.0standard
3.1 this specification is prepared by taking guidance from bs 601:1973
4.0material
4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and
Equivalent to jis c 2553
5.0properties
5.1 specifications and typical electrical and magnetic properties (see appendix 1)
6.0dimension and tolerance
6.1 dimension : as per the purchase order with the tolerance as given table below
Tolerance on width
Nominal width (mm)
Overup to and includingtolerance (mm)
0150+ 0 0.3
150500+ 0 0.5
001000+ 0 1.5
Tolerance on length
Nominal width (mm)
Overup to and includingtolerance (mm)
02000- 0 + 1.5
2000>2000- 0 + 2.0
Tolerance on length
The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be
0.03 mm from the nominal thickness.
Tolerance on edge burr
The tolerance on edge burr not to exceed 0.05mm.
Tolerance on edge camber
Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a:
Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil.
7.0references
(1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
Scrap metal and decommissioned mining equipment,
various ex-mining equipment, chassis of excavators, trucks, loaders, cabins,
roller, rims, tyres, etc. too numerous to list here. full inventory list provided to bona fide buyer
all material will be cut to sizes required by buyer
quantity:5,000mt
Used rails R65 R50
Price-255 usd per tonne.
All prices are including transport, shipping and insurance.
* Procedures*:
1. The Buyer Sends LOI.
2. The seller sends FCO
3. Buyer signs and returns FCO with ICPO with passport copy and company registration certificate
4. The seller sends the SPA to the buyer.
5- Buyer's signature in the contract and return to the seller for counter-signature
- Seller will issue commercial invoices to buyer bank to issue MT 705.
- Seller bank will issue PB of 20% of total invoice value.
- Buyer can view materials at the stores.
*Accepted payment methods:*
- LC for full commercial invoice .
- MT 700 at site.
- 2 options for buyer �°???�°??�½
- Revolving LC bank guarantees from the bank issuing the LC as a commitment from the buyer for the total quantity.
- The Revolving LC, there will be Guarantee from the buyer�¢??s bank for 20% of the total quantity in the contract.
Whether you have a new design or just want to outsource your existing metal stamping parts, we have the presses and experienced tooling engineers to design the dies that can meet your specifications. Sample parts can be submitted for your approval within a few weeks after receiving your cad file and purchase order. We have years of experience working with oem customers and our engineers will communicate directly with yours as needed to address any technical issues prior to volume production. State-of-the-art inspection equipment and iso 9001 certification ensure that we can meet your quality requirements.
Ascustomer requirement
1258 Metal Products Suppliers
Short on time? Let Metal Products sellers contact you.
