Caustic Recovery Plant
Dry Ice
Roller conveyor shot blasting machine for of steel sheets, sections, beam Machine Introduction: H beam shot blasting machine: Shot blasting machine for h beam is designed and produced by adopting the advantages of similar products from both within the country and abroad. The rusting cleaning part (shot blasting) adopts high-efficient blast wheel and full shutter type shot sand separator. The sweeping machine adopts specially made high-strength nylon rolling brush and high-pressure ventilator. The preheating and drying part of shot blasting machine may adopt various heating methods. The paint spraying part adopts high-pressure airless spraying method. The complete set of equipment is controlled by PLC, and is the large-size complete equipment of international advanced. QH69 shot blasting machine is mainly used for surface treatment (namely preheating, rust removal, paint spraying and drying) of steel plate and various structural sections, as well as for cleaning and strengthening of metal structural parts.
Hook shot blasting machine is widely used in foundry plant, forging plant.metal processing. The double hook or Y track rail shot-blasting machines are the most versatile in terms of typical employment and size of the materials to be treated. Moreover the motorised hoists installed on the overhead conveyor allow the lifting of very high loads. The customer can choose the size and loading capacity of the machine according to the parts to be shot-blasted. The hook type shot blasting machine is designed to increase the performance of the hook type machines by keeping the turbines continuously running. The hook inside the blasting machine, once in position, starts to rotate on its axis and move back and forward in front of the turbines (mounted on one side of the machine). These combined movements ensure the complete shot-blasting of the parts external surface. The customer can choose the size and loading capacity of the machine according to the parts to be shot-blasted. Depending on the height of the machine, the installation may require a pit. The shot blasting unit is supplied complete with a self-cleaning dry cartridges dust collector.
Applications: Descaling of forged or heat treated parts Desanding of ferrous and non-ferrous metal castings Deburring of metallic and non-metallic parts Deflashing of die cast parts Contaminant removal The tumbling action of the belt conveyor ensures that components are continually exposed to the blast stream and completely cleaned. For easy unloading, the belt conveyor is reversed, delivering the components into the loading skip or stillage. Optimized shot blast effect: During shot blasting, the workpieces, regardless of size and shape, are evenly and continuously tumbled. This is necessary for the effective and uniform treatment of all surfaces. During tumbling, the workpieces continually undergo shot removal, enabling workpiece interiors and cavities to be perfectly cleaned For the complete removal of all shot, the final tumbling time that follows the shot blast sequence can be regulated to suit the type of workpieces being blast cleaned The tightly sealed, leak-proof blast chamber minimizes shot consumption.
The tumbling action of the belt conveyor ensures that components are continually exposed to the blast stream and completely cleaned. For easy unloading, the belt conveyor is reversed, delivering the components into the loading skip or stillage. Optimized shot blast effect: During shot blasting, the workpieces, regardless of size and shape, are evenly and continuously tumbled. This is necessary for the effective and uniform treatment of all surfaces. During tumbling, the workpieces continually undergo shot removal, enabling workpiece interiors and cavities to be perfectly cleaned For the complete removal of all shot, the final tumbling time that follows the shot blast sequence can be regulated to suit the type of workpieces being blast cleaned The tightly sealed, leak-proof blast chamber minimizes shot consumption.
Hanger hook shot blasting machine: Hanger shot blasting machine is widely used in foundry plant, forging plant. Metal processing. The double hanger or Y track rail shot-blasting machines are the most versatile in terms of typical employment and size of the materials to be treated. Moreover the motorised hoists installed on the overhead conveyor allow the lifting of very high loads. The customer can choose the size and loading capacity of the machine according to the parts to be shot-blasted. The hanger type shot blasting machine is designed to increase the performance of the hook type machines by keeping the turbines continuously running. The hanger inside the blasting machine, once in position, starts to rotate on its axis and move back and forward in front of the turbines (mounted on one side of the machine). These combined movements ensure the complete shot-blasting of the parts external surface. The customer can choose the size and loading capacity of the machine according to the parts to be shot-blasted. Depending on the height of the machine, the installation may require a pit. The shot blasting unit is supplied complete with a self-cleaning dry cartridges dust collector.
Automatic Wire Mesh Belt Shot Cleaning Machine/Sand Blasting/Shot Peening/Sandblasting/Sandblaster/Shot Blasting Machine Inroduction: The Mesh Belt shot blast machines provide a frequency controlled speed variable mesh belt surface on which a variety of parts can be uniformly blasted. The high quality mesh belt ensures that the work piece remains in the perfect position to be blasted. As each part is blasted in a controlled fashion this technology is perfect for thin-walled parts which could be damaged when impacting other parts (for example inside a tumble blasting machine). Capable of fully automatic operation the MB-Line machines are the perfect shot blasters to improve the quality and consistency of your castings, forgings, or other small parts. Automatic Wire Mesh Belt Shot Cleaning Machine/Sand Blasting/Shot Peening/Sandblasting/Sandblaster/Shot Blasting Machine Description: 1. Shot blasting is a method used to clean, strengthen (peen) or polish metal. 2. Shot blasting is used in almost every industry that uses metal, including aerospace, automotive, construction,foundry, shipbuilding rail, and many others. There are two technologies used: wheel blasting or air blasting. Product Advangate: Automatic Wire Mesh Belt Shot Cleaning Machine/Sand Blasting/Shot Peening/Sandblasting/Sandblaster/Shot Blasting Machine Advantage: 1.Using full manganese steel body, use life is 20 years 2.Using advanced wet dust collector system 3.Using crushed shot secondary separation system 4.Using high performance P series impeller head (die steel CNC machining + vacuum heat treatment) 5.Steel Shot Flow Automatic Control System 6.Using 3 layers seal structure for machine body,without any Shot leaked 7.Steel Shot Automatic Recycle Fault Detection Alarm System Automatic Wire Mesh Belt Shot Cleaning Machine/Sand Blasting/Shot Peening/Sandblasting/Sandblaster/Shot Blasting Machine Compared Advantage: 1.Environmental indicators reach the European standards 2.The efficiency is increased by 30% 3.Spare parts usage is reduced by 80% 4.Maintainability is increased by 90% 5.Automation degree increased by 50% 6.Integrated design, more convenient maintenance
rubber belt conveyor shot blasting machine for of medium and small parts, stones, bricks,marbles Machine Introduction: shot blasting machine: Shot blasting machine is designed and produced by adopting the advantages of similar products from both within the country and abroad. The rusting cleaning part (shot blasting) adopts high-efficient blast wheel and full shutter type shot sand separator. The sweeping machine adopts specially made high-strength nylon rolling brush and high-pressure ventilator. The preheating and drying part of shot blasting machine may adopt various heating methods. The complete set of equipment is controlled by PLC, and is the large-size complete equipment of international advanced. shot blasting machine is mainly used for surface treatment (namely preheating, rust removal, etc.) of steel parts and various structural sections, as well as for cleaning and strengthening of metal structural parts.
Powder Coating Line:  We are professional in any kind of powder coating plant design,manufacture,installation,test run,training and thoughtful after sale service in home and abroad. Power and free conveyor is highly automatic and integrative, which can stop individual loads without stopping the entire production line. The main conveyor is moving continuously, but another loading conveyor just move step by step (position: inside the oven, loading & unloading area). The output capacity can be very big if the main conveyor speed is fast, no need to enlarge the oven size. So it takes smaller space than the common tunnel oven design.   Inspired technology:  Power & Free Conveyor Design Power & Free conveyors are twin-rail systems using a power chain to haul the carriers. The power chain is equipped with evenly spaced rigid dogs, which latch onto the movable cam on the trolley to form an interlocking connection.   Stops and contact skids allow the carriers to be automatically stopped, closely buffered and automatically released as required.  Carrier spacing and moving speeds are variable and can be set independently for each individual chain circuit.  If needed, P & F conveyors can also be equipped with destination controls,which also provide solutions to complicated distribution, sorting and special task problems.  Power& Free Conveyor Advantages:  Compact design with buffering mechanisms inside the track.  Flexible installation with minimum space requirements. Allow chain transfer at any time, regardless of dog spacing.  Fully automatic operation with hierarchical control system with user-friendly visualization interface.  Control functions can be linked to central plant computer system.  High availability through modular design, easily exchangeable components,quick repair of breakdowns.  Transfer-free carrier movement, including at lifting stations.
1.Capacity: 500- 10000 Ltr 2.Number Of Wheel: Any applicable numeric value 3.Brand: Gourika India Ltd 4.Material:Mild Steel 5.Power Source: Diesel 6. Diameter: 4 Feet -36 Feet # We are the leading manufacturers of Sewer Suction Cum Jetting Machine. The equipment consists of suction and a high-pressure water jetting equipment integrated to complete the Suction-cum-Jetting Combination unit. De-choking and de-silting of the sewer and drain water lines and chambers will be carried out by the High Pressure Jetting System working on the principal of hydrodynamic cleaning by injecting high pressure water into the lines through a suitably dimensioned sewer jetting hose and special cleaning nozzles. Aspiration of the effluent from sewer and drain water lines and chambers will be carried out on the principle of generating high vacuum in the sludge compartment for siphoning out effluents, liquids slurry, sludge and other materials from depths of about approximately 6 to 7 mtrs, depending on the specific gravity of the effluent
1. The multi-functional shoe making machine is used for leisure shoes and the sole and the upper surface pressing together or outsole combination process in all kinds of sports shoes. The water hydraulic oil is injected into the cylinder and the stretched rubber sheets are extruded by pressure, and the use of expansion compression principle can be applied to achieve a full range of extrusion purpose, so that the closed fitting is perfected. The processing shoes are placed in the elliptic oil hydraulic cylinder that conforms to the engineering principles for compression molding, which has the easy mechanical operation, and the durable rate of each rubber sheet is more than 300 thousand pairs which is a big break in molding process at present. This machine can replace the walled shoe attaching machine when it is placed on the molding line, and replace the walled shoe attaching machine and hydraulic press when it is placed on the soles processing line. It is a machine with multi-use in the development room, which can be used for pressing the soles while pressing into a shoe type. 2. By adopting the oil hydraulic system, the pressure can be adjusted according to the shoe type, and the average pressure is up to 30kg/cm2. 3. This molding machine conducts full compression on the rubber sheet, and it can finish the procedures that walled shoe attaching machine cannot complete. For example, the edge strip can be pressed well if there is side wall, strake on the side or behind of the molding shoes.
1. The multi-functional shoe making machine is used for leisure shoes and the sole and the upper surface pressing together or outsole combination process in all kinds of sports shoes. The water hydraulic oil is injected into the cylinder and the stretched rubber sheets are extruded by pressure, and the use of expansion compression principle can be applied to achieve a full range of extrusion purpose, so that the closed fitting is perfected. The processing shoes are placed in the elliptic oil hydraulic cylinder that conforms to the engineering principles for compression molding, which has the easy mechanical operation, and the durable rate of each rubber sheet is more than 300 thousand pairs which is a big break in molding process at present. This machine can replace the walled shoe attaching machine when it is placed on the molding line, and replace the walled shoe attaching machine and hydraulic press when it is placed on the soles processing line. It is a machine with multi-use in the development room, which can be used for pressing the soles while pressing into a shoe type. 2. By adopting the oil hydraulic system, the pressure can be adjusted according to the shoe type, and the average pressure is up to 30kg/cm2. 3. This molding machine conducts full compression on the rubber sheet, and it can finish the procedures that walled shoe attaching machine cannot complete. For example, the edge strip can be pressed well if there is side wall, strake on the side or behind of the molding shoes.
Description: DZSF Series Linear Vibrating Screen is a kind of common closed light-duty vibrating screen equipment which use excellent vibrating motor as power source,that the materials can be thrown up on the sieve and forward to make a straight movement. The material evenly enter into the inlet from the feeder.It can be equipped with single or multi-screen to achieve the grading, removing impurity, removing dust, testing, washing selecting, dehydration etc. Features: 1.Dust proof ,durable design,simple operation. 2. Easy and convenient to clean up and change meshes. 3.Energy-saving and low noise with vibration motor. 4. Carbon steel or stainless steel. 5.Mesh size can be customized by customer standard.
1)It has the functions of high strength, heat insulation, flame retardant, wear resistance and so on. Such as aramid fiber core-coated yarn, composite yarn containing metal wire, acrylic composite core-coated yarn, aramid fiber high temperature filter yarn, etc. This kind of yarn is often used in industrial products, such as various clutch sheet frame materials, advanced brake lining base cloth, heat insulation packing, flame retardant conveyor belt, cutting-proof gloves and so on. Its raw materials are generally functional fibers which are difficult to control in traditional spinning mode, such as glass fiber, aramid fiber, carbon fiber and so on. 2)Winding liquid filter core yarn with good bulking and density. Such as friction spinning polypropylene filter yarn, because of its unique outer winding structure, the winding filter core not only has high filtering precision, but also has a large flow rate. It is deeply favored by users. Others such as friction spinning skim cotton cabin filter yarn and friction spinning glass fiber high temperature resistant cabin filter yarn also have their own characteristics, and the products have higher added value. 3)Waste spinning engineering products. Merchants have developed various fiber leftover bits and pieces into mop yarn, floor cleaning towel yarn and so on with distinctive characteristics through friction spinning machine, and the products are very popular. And products such as steel wire ropes, electric wires, cable core yarn, which are also woven with leftover bits and pieces, not only achieve the utilization of waste, but also create considerable economic benefits.
The equipment is mainly composed of main box, base, rear tailstock and electrical control. Application: High and low voltage power transformer winding machine is suitable for winding of reactors, high and low voltage coils of power transformers and other similar coils. Feature of Machinery 1 The mechanical transmission part of the winding machine is set in the bedside box, and the transmission part is installed on the operating side of the bedside box. High and low spindle speed change with variable speed handle 2 The winding machine uses a frequency converter to achieve stepless speed regulation, smooth starting and constant torque.There are three positions for adjusting the shifting handle: low speed, neutral, high speed; set the number of laps, and automatically stop. 3 The machine is equipped with an automatic brake device to prevent reverse when the winding is stopped. 4ã??The machine can preset the number of coil turns to control the forward and reverse rotation; the electronic reversible counter has a forward and reverse counting accuracy of 1/10 turns, and has a power failure memory function. 5 The button station is controlled centrally, and the start and stop of the spindle faceplate is controlled by a foot switch or a key. Technical description: 1ã The main box is composed of a box body, a transmission system, a shifting handle, and a motor. The two-stage machinery of the headstock has step-variable speed control and the stepless speed regulation of the variable-frequency motor constitutes the joint speed regulation system of the host, which makes the entire equipment start-up process stable and the braking accurate and reliable. The motor torque is decelerated and amplified by the headstock to provide winding torque. There are 2 gears for mechanical speed change, each step is variable frequency stepless speed regulation. 2 Rail and tailstock part The tailstock is integrated with the main box, and is mainly composed of a tailstock and a guide rail. The tailstock can be manually moved axially on the guide rail of the base to meet the needs of wire molds of different lengths. By turning the hand wheel, the back top can be extended or retracted, which is convenient for moving the mold up and down and improving the strength. The locking handle can lock the idler roller and tighten the coil to support its weight. 3ã??Electronic control system The electric control system consists of electric control cabinet, inverter, electronic counter, foot switch and other electrical appliances. The speed of the spindle is controlled by the inverter. The counter can count forwards and backwards, and has a power-off memory and automatic stop function after setting the number of turns. The electronic counter value range of 0-9999 turns is operated by the foot switch to operate the entire winding process.
Pressure Pulse Testing Machine has a high performance, which has adopted advanced technology abroad and combined with the actual demands at home. Its main components are imported hydraulic ones. The whole equipment has simple operation and stable performances. It has combined with American NI measurement and control software (LABVIEW software) and can conduct various pressure pulse tests. ODMT can develop and design different kinds of pressure pulse test equipments according to customers requirements. We can provide reliable pressure test. Besides, a comprehensive test equipment which can control the temperature of text medium and the text environment is also provided according to the requirements of the text pieces. Technical Parameters: 1.Type: hydraulic drive and control system 2.Text medium: hydraulic oil or water 3.Text pressure: designed according to customers requirements 4.Pulse frequency: adjustable within 0.5-1HZ 5.Number of the test pieces: designed according to customers requirements 6.Single circulating time: Maximum 1,000,000 times (settable) 7.Control mode: PLC control; users set the test pressure, pulse times and pulse frequency manually; after reaching the set text times, the machine stops automatically and alarms.
Mechanical power press
Chocolate Coating Machine QUALTY : All parts of the machine are produced from 304 qualty stainless steel materials SYSTEM : The drum system. Push-up roller mixer. Speed control.Control panel. Chocolate thinning fan. Wire tape up to 40 cm POWER : Wire tape 0,75 kW mixer 1,1 kW output transfer drum 0,75 kW DIMENSION : Width 99 cm - Height 108 cm - Length 120 cm WEIGHT : 270 kg CAPACITY : 100 kg
this machine is designed for heat transfer artwork onto flat item,t shirt mouse pad tiles. A heat press is a machine engineered to imprint a design or graphic on a substrate, such as a t-shirt, with the application of heat and pressure for a preset period of time. While heat presses are often used to apply designs to fabrics, specially designed presses can also be used to imprint designs on mugs, plates, jigsaw puzzles, caps, and other products.
