"Large capacity Dex port availableFront Glass Vending machine with cooling Bill,Coin,Coin Dispenser(MDB Protocol) Drop sensor system, guarantee the selected item is delivered to the customer or their money is returned" 76" (192cm) 47"(120cm) 36" (92cm)
"Large capacity Dex port availableFront Glass Vending machine with cooling Bill,Coin,Coin Dispenser(MDB Protocol) Drop sensor system, guarantee the selected item is delivered to the customer or their money is returned" 76" (192cm) 72"(185cm) 36" (92cm) 1124 Lbs.(510 kg) 220V,50HZ
"Large capacity Dex port availableFront Glass Vending machine with cooling Bill,Coin,Coin Dispenser(MDB Protocol) Drop sensor system, guarantee the selected item is delivered to the customer or their money is returned" 76" (192cm) 73" (185cm) 36" (92cm) 1102 Lbs.(520kg) 220V,50HZ Up to 86 Items
"Large capacity Dex port availableFront Glass Vending machine with cooling Bill,Coin,Coin Dispenser(MDB Protocol) Drop sensor system, guarantee the selected item is delivered to the customer or their money is returned" 76" (192cm) 47" (120cm) 36" (92cm) 723 Lbs. (328 kg) 220V,50HZ Up to 40 Items
Hongxing Automatic ram extrusion machine for PTFE rod HX30 Hongxing Automatic Ram extruder for PTFE rod Hongxing automatic ram extruder for PTFE rod or UHWM-PE rod extrusion, with full cabinet and PLC control. Ram extruder for PTFE Rod outer diameter: 4-30mm Extrusion rod number:1-18pcs Raw material: PTFE presintered powder(virgin or recycle powder is accept it) Tolerance: +0.1mm Extrusion capacity: 70-100KGS/24hours Delivery date:45 days after order confirm Warranty: 12months for ram extrusion machine for ptfe ROD Automatic ram extrusion machine for PTFE rod from Hongxing factory Strandard export packing for PTFE Rod Ram extruder
Mobile:+86-13849050429 Skype:bettysun2011 Pls check our website : http://www.yxboiler-factory.com/ EMAIL BOX: sales @ yxboiler-factory.com A boiler economizer is a device that is designed to increase the operating efficiency of a boiler, cutting down on its operational costs over the lifetime of the boiler. Although the savings on any given day may be relatively small, the impact over time can be significant; some boilers are designed with economizers built in, while in other cases, an economizer can be fitted on after the act. The boiler economizer acts as a waste heat recovery device, ensuring that this heat does not go unused. Instead, the heat is used to essentially preheat the water, so that less heat is required to bring the water to a temperature high enough to make steam. Pls note :The economizer pipes is ok for customized 1-1000 sets
Mobile:+86-13849050429 Skype:bettysun2011 Pls check our website : http://www.yxboiler-factory.com/ EMAIL BOX: sales@yxboiler-factory.com Autoclave kettle is large pressure container by steaming the aerated concrete, sand lime brick and coal-dust brick. Also are widely used in other production projects which need steamng curing. Such as super-strength gypsum, insulation materials,rubber products, high strength glass and cement tubular pile and wood, medicine, chemical industry, etc. (1)A single piece 16MNR steel plate is pressed to form the kettle cover, kettle cover flange and kettle body flange. (2)Welding seam of the pressure parts all have heat treatment and strict nondestructive testing.. (3)Kettle door has manual and automatic opeartion according to customers demands. (4)This kettle is opened very easily. (5)This kettle occupies little space. 1-1000 sets
Mobile:+86-13849050429 Skype:bettysun2011 Pls check our website : http://www.yxboiler-factory.com/ EMAIL BOX: sales@yxboiler-factory.com Series of DZL quick fitting boiler is the horizontal tri-returning water and fire pipes chain grating boiler,which uses medium quality soft coal.The boiler body is a single cylinder type,portrait arranged; there are left and right 2 rows of fire pipe bundles inside boiler cylinder to form convection heat receiving surfaces,the boiler cylinder to form convection heat receiving surfaces, the boiler cylinder and water cooling walls at both sides shape the furnace radiation heat receiving surfaces;the combustion equipment uses light chain grating;exit shop in whole machine & quick fitting type. The electric control realizes grating step free timing,the extreme parameter alarm and inter-lock protection. Features of this series of boiler:compact structure,small volume;convenient installation,cheap in fundamental construction; mechanized coal feeding and cinder removing;the output of the boiler is in sufficient and high efficiency.It is the well appreciated equipment for extensive steam supplying equipment for medium and small enterprises and public heating. 1-1000 sets
Mobile:+86-13849050429 Skype:bettysun2011 Pls check our website : http://www.yxboiler-factory.com/ EMAIL BOX: sales@yxboiler-factory.com Flake type chain grate stoker is a new style fire grate. It features easier to maintain and repairing (No need stop boiler to replace broken grate bars), also reduce the leak of coal from the grate stoker surface. Its performance and operation is constant and reliable. More and more plants prefer this type chain grate because of its good structure. Flake type chain grate stoker has two types: Small flake type chain fire grate: for 4t/h to 25t/h boiler Big flake type chain fire grate: 25t/h to 60t/h boiler. Boiler Chain Grate Boiler chain grate stoker Boiler Travelling grate stoker Boiler moving grate stoker Small flake chain grate Flake type chain grate Chain grate range from 0.5t 2T/H to 35t/h. The chain grate stoker is a mechanization equipment applied mostly in steam boiler, hot water boiler and thermal oil boiler. It features reasonable structure, reliable performance and convenient installation, etc.The series products adapt light chain grate stoker and reasonable air distribution device and also strengthen the seal at both sides of chain grate as well as configuration reasonable front and back arch. It features strong suitability in combustion and reasonable air distribution for combustion and quick fire starting. Operation practice provided that combustion heat value is about 18840 kJ/kg. Soft coal with more than 20% of volatile amount and mixed coal can be combusted normally. Moreover it can also combust waste industrial materials such as wood block, sugarcane residual, etc 1-1000 SETS
Mobile:+86-13849050429 Skype:bettysun2011 Pls check our website : http://www.yxboiler-factory.com/ EMAIL BOX: sales@yxboiler-factory.com Products Summarization The BH series burners,the Mechanical & Electrical lntegration light oil burners which extensive use the steam boilers,heating water boilers,heat conducting oil stove,direct- fired generator,lithium bromide air-conditioning pant and other industrial heating and parch stove equipments,are designed by advanced combustion technology in the world and consult the En267 Standardand the national interrelated standard. Performance feature: Al-in-one blower. Auto-operation Manual switch for one stage/two stage Sweep the tube before ignition. Safety flame monitors system. The air gate will close automatic commissioning and maintenance.It's Convenient for the installation,commissioning and maintenance.The burner is easy to install for the portable body,The client just connects the power supply and gas suply.Our burner is also ok to fuel kerosene oil. 1-1000 sets
Volumetric feeder provides low cost and easy option in batch or continuous applications, especially when the bulk density of the fed material is consistent or when precise feed accuracy is not so important for the quality of end product. Frequently volumetric feeder is used in gain-in-weight batch application since higher accuracy can be achieved. When process requirement is more demanding, volumtric feeder with gravimetric scale and loss-in-weight control can be used. Our volumetric feeder can provide reliable and stable performance. Single screw feeder is the best choice for free flowing materials, while twin screw feeder is the the best solution for difficult-handled materials. We have a full range of volumetic feeders with a number of models and different-sized hoppers to meet your specified requirements. Twin-screw volumetric feeder is applied to provide accurate volumetric feeding for poor flowing powder, fiber and flake materials. All parts which contact fed material are made of stainless steel. It is easy to disassembled for cleaning or changing parts. The special bowl-shaped hopper makes material flow from all directions into the screw evenly. It can also avoids material build-up and make feeding more accurate. Two types of hopper, symmetrical or asymmetrical, can be chosen. The standard construction material of hopper is SS304. SS316 and SS316L are optional to be used. For poor flowing materials which tends towards bridging, a vertical agitator is optional to add. For different environments, different construction materials of screw can be used. The screw materials can be SS304, SS316L, copper, carbon steel and Hartz alloy. Plywood case, 1 set/case
Applications When the bulk density of the fed material is not consistent, or when the precise feeding accuracy is critical to the end product quality, the loss-in-weight feeder needs to be used. The loss-in-weight feeder can be used in batch or continuous situations. Frequently it is applied in continuous processing, such as extrusion. During extrusion process, multiple ingredients` ratio needs to be controlled precisely. Characteristics Our loss-in-weight feeder can provide high precise, reliable and consistent feeding performance. Single screw loss-in-weight feeder Is the best choice for free flowing materials, while twin screw loss-in-weight feeder provides the best solution for difficult-handled materials. The loss-in-weight feeders are available with a full range of models and different sizes of hopper. It can satisfy the feed range of 0.5-1000L/hr. Load Cell and Gravimetric Control System High precise technology is adopted in gravimetric feeder. Our weighing module provides slipt second and milligram range performance. It is designed to be used in harsh industrial environment. Equipped with the first class soft ware, our loss-in-weight feeder can provides consistent, precise, reliable and repeatable results. The gravimetric controller and operation interface allows for individual unit and recipe control. Each feeder has its own control board. The control board and the operation interface is connected by industrial protocol. The online controller can combine the motor driver with the feeder controller together. HMI provides extreme flexibility for recipe storage and memory. Up to 8 feeders can be working together simutaneously and be connected to DSC system of the main processing machine. Single Screw Loss-in-weight Feeder Our single screw loss-in-weight feeder can provides high precise,high valued feeding for pellet, granule, free flowing powder and other bulk materials. The feed rate is 0.5-1000L/hr. The accuracy can reach ¡¡¡ì¡¨¨0.2%. According to the characteristics of different fed materials, the single screw loss-in-weight is available with a wide range of interchangeable screws. Plywood case, 1 set/case
Application Liquid loss-in-weight feeder is designed to provide gravimetric feeding of liquid materials.It is most frequently applied in continuous processes,such as feeding a compounding extruder where difficult flowing liquids must be metered at precise feed rates. These liquids are often waxy or viscous and must be heated to flow properly. Characteristics ¡ï consists of a storage tank mounted on a high accuracy scale designed for industrial applications. ¡ï The liquid is metered by a pump positioned off the scale so that only the liquid and its container are weighed. ¡ïIf the temperature of the liquid to be fed must be maintained at a constant level, a strip heater or transfer heater using oil or water may be employed. ¡ï When using a strip heater, temperature is controlled by a thermostat and a safety thermostat. An insulating jacket is placed over the strip heater. The connecting line is also heated and thermally insulated. ¡ï When using heat transfer, the tank is double-walled and filled with oil or water. ¡ï The sophisticated load cell provides split-second, high precision weighing in the milligram range and is specially designed for harsh industrial environments. ¡ï Liquid feeders are easily integrated with gravimetric bulk solids feeders. The gravimetric controller and operation interface allow for individual unit and recipe control. Each feeder has its own control board. Connection between control boards and operation interface is supported by industrial protocol. Plywood case, 1 set/case
Volumetric feeder provides low cost and easy option in batch or continuous applications, especially when the bulk density of the fed material is consistent or when precise feed accuracy is not so important for the quality of end product. Frequently volumetric feeder is used in gain-in-weight batch application since higher accuracy can be achieved. When process requirement is more demanding, volumetric feeder with gravimetric scale and loss-in-weight control can be used. Our volumetric feeder can provide reliable and stable performance. Single screw feeder is the best choice for free flowing materials, while twin screw feeder is the the best solution for difficult-handled materials. We have a full range of volumetic feeders with a number of models and different-sized hoppers to meet your specified requirements. Single screw volumetric feeder is applied for pellet, granule and free flowing powder to provide volumetric feeding. A series of interchangeable screws are available for our single screw feeder to meet the requirements of different materials being fed. The feeder is placed on the painted steel plate. All the feeder parts which contact fed material are made of stainless steel. The volumetric feeder can be disassembled easily for cleaning or changing parts. There are two types of hopper shape: symmetrical and asymmetrical. The hopper design can allow material from all directions to flow evenly to the screw, which can avoid material build-up and make feeding more accurate. The most suitable screw type is determined by the characteristics of fed materials. Therefore, please provide detailed information about your material when inquiring. Plywood Case, 1 set/ case
Applications When the bulk density of the fed material is not consistent, or when the precise feeding accuracy is critical to the end product quality, the loss-in-weight feeder needs to be used. The loss-in-weight feeder can be used in batch or continuous situations. Frequently it is applied in continuous processing, such as extrusion. During extrusion process, multiple ingredients` ratio needs to be controlled precisely. Characteristics: 1. Nice Appearance. Compared with traditional feeders, many improvements have been made in our appearance of our feeders. 2. Small Volume. Since it is small, it can be moved to a new place easily, especially when production process is changed or when production technology is improved. 3. Low Noise. Our feeders make almost no noise. 4. Convenient Cleaning and Easy Maintenance. 5. Extremely High Stability. In order to ensure precise feeding in a long run, self-detecting function is included in our feeders, which can detect mechanical wearing and the effect on feeders when frequency fluctuates, then make real-time correction accordingly. Therefore, feeding precision won`t be affected when a mechanical part is replaced or when it is being used for a long time. 6. Friendly HMI. Easy operating touch screen system. Input to the system is more humanized. An operator can master all the operations in only a few hours. 7. Wide Range. Without replace a new mechanical part, a wide range flow rate can be set. In this way, a new manufacturing technique can be shifted to quickly. 8. Excellent Control System. According to customer`s requirement, a control system can control multi-feeders while the feeding accuracy will never be affected. 9. Screw Options. Depending on the fed materials characteristics, interchangeable screws in different shape and materials can be chosen. The material of a screw can be PS, carbon steel, 304 stainless steel, 316L stainless steel, hastelloy alloy or copper. Plywood case, 1 set/case
We Ultra Febtech - An ISO 9001:2008 Certified company engaged in manufucturing of CMC Plants to convey the material. First cellulose react with caustic to form alkali cellulose then react with mono chloro acetic acid or it’s salt from sodium carboxy methyl cellulose. During the reaction of alkali cellulose with etherification agents and in the subsequent reactions, sodium chloride (common salt) is produced as a major by-product. This is washed out together with any other byproducts or, in the case of technical-grade NaCMC, left in the product. The dried cellulose ethers are then processed into granular or powder products and in some cases modified with other additives.
We Ultra Febtech - An ISO 9001:2008 Certified company engaged in manufucturing of Ultrafine Pulverizer to Grind the material. A unique equipment to handle the mass that is most difficult to grind. It gives the desired fineness with a very high capacity and that too at lower power consumption. No special feeding systems such as screw conveyor or rotating valve is required. It pulls the material in, due to high suction of air and throws in high vertical discharge pipeline makes even drying possible with in the same equipment. Less maintenance makes the operation of grinder unstoppable. The equipment is available in vertically mounted or horizontally mounted on tough frame. Various capacities are available.
We Ultra Febtech - An ISO 9001:2008 Certified company engaged in manufucturing of Flaker to Grind the material. Some process need only crushing of the material to meet either to requirement of coarse material or to feed smaller sized material to another grinder. Two hardened rolls rates towards each other. They are kept nearer to each other by means of either mechanical devices or with hydraulic system. This system helps to create the pressure on the rolls and makes the crushing possible. The larger particle of mass, cereals, pulses is pushed between the rolls uniformly spread and with continuous rate through a separate device. A dried feed mass gives material at the bottom with reduced size or if soaked cereals or pulses, give you the material in a flake form. Due to use of roll, Flakers also known as a roll crusher.
We Ultra Febtech - An ISO 9001:2008 Certified Company Engaged in Manufucturing of Machinery Product to Convey the Material. The plant has been configured and designed in such a way that minimum work force will require. The guar split will be fed in to the pneumatic system to feed in to the turbo screen. The turbo screen is suggested at the high of plant. The screening will be employed for the removal of foreign matter. This screened material will be stored in a storage hopper. The guar splits will fall from the screens by gravity to the storage hopper, which is configured below the screen. From storage hopper material can be taken in to double cone mixer as and when required by gravity for the rehydrating of guar splits. All the rehydrated guar split will be sent to the hopper of Flakers at a time by gravity. Flakers will crush the guar splits and crushed guar splits will go into the ultrafine grinder at the uniform rate. Ultrafine grinder is proposed for the grinding of crushed guar splits. This grinder has ability to grind the material without generating too much heat. Material will be fed into the dryer. Oil will be the media to convey the heat and deliver to the air. This hot air will take the material into the dryer line where actual drying will take place. Attached cyclone system will separate the material and hot air. To heat the oil Thermal boiler will be used. The material will be screened through centrifugal screen. Material passing through the screen will be again screened through turbo screens as additional control. This material will be sold as a premium product. Oversize of the centrifugal screen will be screened through turbo screen to separate another grade in terms of particle size followed by additional screening. The oversize will be screened through another turbo screen to separate another grade. Oversize will be passed through another grinder. The material will be passed through another screen. Oversize will be recycled to the same grinder. Final material coming out from all the screens will be sent separately by gravity in to the Nauta mixer for the blending and to make a uniform lot. The products will be tested and packed. The plant can be operated by 2 skill workers in a shift. The loading/unloading and the packing of the final product can be done on contract basis.
We Ultra Febtech - An ISO 9001:2008 Certified Company Engaged in Manufucturing of Machinery Product to Convey the Material. The plant has been configured and designed in such a way that minimum work force will require. The guar split will be fed in to the pneumatic system to feed in to the turbo screen. The turbo screen is suggested at the high of plant. The screening will be employed for the removal of foreign matter. This screened material will be stored in a storage hopper. The guar splits will fall from the screens by gravity to the storage hopper, which is configured below the screen. From storage hopper material can be taken in to double cone mixer as and when required by gravity for the rehydrating of guar splits. All the rehydrated guar split will be sent to the hopper of Flakers at a time by gravity. Flakers will crush the guar splits and crushed guar splits will go into the ultrafine grinder at the uniform rate. Ultrafine grinder is proposed for the grinding of crushed guar splits. This grinder has ability to grind the material without generating too much heat. Material will be fed into the dryer. Oil will be the media to convey the heat and deliver to the air. This hot air will take the material into the dryer line where actual drying will take place. Attached cyclone system will separate the material and hot air. To heat the oil Thermal boiler will be used. The material will be screened through centrifugal screen. Material passing through the screen will be again screened through turbo screens as additional control. This material will be sold as a premium product. Oversize of the centrifugal screen will be screened through turbo screen to separate another grade in terms of particle size followed by additional screening. The oversize will be screened through another turbo screen to separate another grade. Oversize will be passed through another grinder. The material will be passed through another screen. Oversize will be recycled to the same grinder. Final material coming out from all the screens will be sent separately by gravity in to the Nauta mixer for the blending and to make a uniform lot. The products will be tested and packed. The plant can be operated by 2 skill workers in a shift. The loading/unloading and the packing of the final product can be done on contract basis.
