This equipment is formulated in accordance with JIS D 0203 standard to test the waterproof performance of the product, equipped with an automatic water inlet and water circulation device, effectively saving money. Corresponding test chambers are prepared according to different test requirements. The multi-function controller is easy to operate, one-key controls the test requirements parameters, and can be connected to the PC terminal remotely to facilitate the download and use of test data. It is mainly applied to the automobile industry.
Larger series sand and dust test chambers allow for large and more quantity specimens, a capacity of 1500 liters and 2000 liters as standard. Great for laboratories and large industrial products. Sand and dust test chambers are made for the simulation of dust and sand conditions. These dust test chambers are used to test the exposure of automotive and electronic components under extreme environmental conditions in order to validate product seal. Dust ingress test methods included IEC60529, ISO20653, MIL-STD-810G, and many others. The airflow circulates upward from the bottom, blowing the dust circulation, forcing dust around the specimens. All models are upgraded to programmable controller and Ethernet access that provides simple operation and control.
Over 29 different models let you choose size, configuration, and performance to suit many types of environmental test conditions. Temperature change rates from 1 to 15 C/min.Low temperature available: A: -20, B: -40, C: -70 , D: -86 .E:-200â ( liquid nitrogen refrigeration. Included are ultra low-temperature test chambers, fast temperature change rate chambers (15/min), and liquid nitrogen refrigeration test chambers. To perform cold resistance test, thermal cycling test, ultra low-temperature test, high-temperature test, storage condition, and calibration function.
Application: Ozone resistance test chambers test elastomers (rubber) in the condition of ozone exposure, to simulate and measure rubber aging by means of ozone within a few days. Structure: Built with dynamic and static sample holders, cooling system, humidity system, air circulation, ozone generating unit, ozone exhaust device, and control system. Standard: ASTM D1149, IEX6006811-403, ISO1431, ASTM D1171. Operate: All models are upgraded to a programmable controller and Ethernet access that provides simple operation and control.
SO2 Noxious Gas Test Chambers reproduce damages by temperature, relative humidity, and noxious gas Corrosion to material, components, and constructions. This noxious gas chamber can be used for single gas tests and mixed gas tests. Test methods are in accordance with IEC 60068-2-42, IEC60068-2-60, and other standards.
This chamber is for temperature & humidity tests, cold resistance tests, thermal cycle tests, ultra-low temperature tests, high-temperature tests, storage conditions, and calibration functions.
This UV test chamber is used in tests that incorporate UV light, temperature, condensing humidity, water sprays, and irradiance control. UV weathering resistance test chamber uses UVA-340, UVB-313 fluorescent UV lamps for a variety of test conditions. Accelerated weathering tests included color change, gloss loss, chalking, cracking, crazing, hazing, blistering, strength loss and oxidation, and many others. UV series weathering chambers are upgraded to a programmable controller and Ethernet access that provides simple operation and control.
Xenon arc lamp test chamber reproduces weathering damage by sunlight, temperature, humidity, and water spray. Xenon weathering test chambers are utilized in textiles, dyes, leather, plastics, paints, coatings, automotive interior parts, electrotechnical products, color building materials. To perform weathering test, colorfastness tests, aging test, hardening test, softening test, crack. Accelerated weathering test methods included ISO4892, ASTM G155-1/155-4, ISO 105-B02/B04/B06, ISO11341, AATCC TM16, TM169, , JIS L0843, SAEJ1960/1885, JASOM346, and many others. XL-S-750 xenon weathering chambers can place 42 pieces of specimens, are an upgrade to a programmable controller and Ethernet access.
IPX5 IPX6 Water Jetting Test Chamber is applied to test the water tightness of enclosures of automotive parts, outdoor lamps, and electronics parts. The chambers are built with the water-tightness of sealed components such as headlamps, Power connectors. A waterproof power connector in the test room can easily supply electricity to the specimens. IPX5 and IPX6 function on one test chamber, make testing convenient and cost-effective.
LIB Water spray test chambers can perform tests in accordance with IEC60529, and IPX1 IPX2 IPX3 IPX4 protection code. The chambers are built with the water-tightness of sealed components such as headlamps, Power connectors. A waterproof power connector in the test room can easily supply electricity to the specimens. The water spray Chamber built with a water re-circulation system that reduced water use and a series of water pipes. The incorporated rotating turntable can promote an even spray of water over the surface of the products under testing. An automatic water supply ensures an adequate supply of water and automatic testing. All models are upgraded to a programmable controller and Ethernet access that provides simple operation and control. Various sizes and configurations to suit many types of test conditions.
IP5X IP6X Sand and Dust IP Test Chambers are capable of 800 liters,1000 liters, 1500 liters and 2000 liters. Considering that some specimens are smaller and less, so we designed and produced small dust chambers and larger dust ingress test chambers. Sand and dust test chambers are made for the simulation of dust and sand conditions. These dust test chambers are used to test the exposure of automotive and electronic components under extreme environmental conditions in order to validate product seals. Dust ingress test methods included IEC60529, ISO20653, and many others. The airflow circulates upward from the bottom, blowing the dust circulation,forcing dust around the specimens. All models are upgrade to programmable controller and Ethernet access that provides simple operation and control.
We designed and produced high-temperature drying ovens at temperatures up to +250 C, +500 C, +800 C, +1000 C, +1200 C with small, medium, and large volumes. Ovens are used for high-temperature drying, paint drying, drying glass and plastics, ink, and removing moisture, wood drying, and high-temperature tests. Applied to aerospace, automotive, electronics, metalworking. Drying ovens are available in various sizes and temperature ranges, including standard and custom ovens.
A Whole Set of water spray IP Test apparatus, IPX1 X2 X3 X4 X5 X6 X7 X8 full set water ingress IP test equipment -No Housing Type. One complete system to perform IP dust and rain test, one-stop solution for IP test.
The environmental test chamber is for PV modules (solar panels) thermal cycling, humidity freeze cycle, and damp heat RH testing, to test whether PV modules can withstand high temperature with humidity and low temperature, to test its fatigue and thermal failure after temperature repeated changes, to confirm its thermal stress PV modules generated under high humidity circumstance and capability of long-term resistance to moisture penetration. This test chamber is widely used in solar panel testing. Different models let you choose size, configuration, and performance to suit many types of solar panels for IEC, UL test methods.
Cyclic corrosion test chamber exposes sample to a series of different environments in repetitive cycles that incorporate temperature, humidity, salt spray, and dry. SC series corrosion chambers are upgrade to programmable controller and Ethernet access.
Cryogenic Chamber uses a mechanical compressor to refrigerate to -120 C, replacing the traditional liquid nitrogen refrigeration method. It is mainly used in high-precision fields such as aerospace, military, electronic component testing, and high-end processing industry quenching processes.
Benchtop Temperature humidity Test Chambers are Small, bench-top test chamber for simulating temperature and humidity environments. Included only temperature, temperature and humidity test chambers. Widely used in electronics, automotive, manufacturing, research and laboratories. Its very good advantages are small, desktop, small footprint, portable, stable performance and Full function. A Benchtop Environmental Chamber offers flexibility, uniformity, and control accuracy. Small & Affordable.
A salt spray test chamber is used to test the anti-corrosion quality of all the materials surfaces of painting, coating, electroplating in the condition of salt spray environment. Basic salt spray test chambers meet ASTM, ISO, IEC, and other International Standards test methods, capacity available in 108L, 320L, 410L, 780L, 1000L, 1600L capacity.
The 9mm screw top vials with cap and septa is compatible with autosamplers using 11mm crimp top vials, â?¢Can be used in general autosamplers, Suitable for use in Agilent, Shimadzu or Waters Systems,Wide mouth,Borosilicate glass,Flat bottom,With marking spot,Cap with teflon/silicon/teflon septa,Cap to be packed separately from vials
Product Overview 1. Audible and Visible Alarms alert the user and shuts off heaters to setpoint deviation. 2. Automatic restart after power interrupt with Non-Volatile Memory keeps studies running smoothly. 3. Insulating and tempered glass door provides good view of incubating state without opening lids. 4. High quality and low noise imported CFC free compressors ensure refrigeration effect and stable. 5. The EMC (Electromagnetic Interference) design makes machine more accurate and stable. 6. Open-Door Cutout Switch stops agitation when chamber is open providing a more favorable work environment. 7. With ultraviolet sterilization function. Specifications 1. LCD Touch Screen that making parameters setting and viewing easily. Such as: a. The setting temperature, speed, time and the real temperature,speed, remaining time are shown simultaneously. b. Keyboard blocking prohibits miss operation. c. Setting rotation direction is positive or reverse. d. Setting circulation fan opens normally or automatically. e. Data memory function can check the history record within 3 months. f. Such data curves as temperature and speed can be displayed. g. The data easily transfer through the USB interface. 2. Timing frost-removing function, the timing range is 1to 89minutes and the defrost interval is 30-600 minutes adjustable, ensures machine working long time in low temperature without ice block. Tech. Parameters Model ZQTY-90E Shaking Range 10-400rpm Shaking Control ±1rpm Orbit (Diameter) �26mm Temp. Range 4~60(at 23~25) Temp. Accuracy ±0.1 Temp. Uniformity ±1(at 37 ) Display LCD (Touch Screen) Parameter Control P.I.D Microprocessor Max. Capacity (Stainless steel clamps) 250ml 30 or 5000ml 4 Timer Range 0-999.9 hrs. Platform Size (LW) 518mm 424mm Power Source AC220 ±10%(110V is optional) 50~60Hz Overall Dimensions (LWH) 860mm 665mm 640mm Weight 118kg Noise Level
