Good scrap wires need good copper wire recycling machine to process, so do you need it small copper granulator machine BS-D75 is in running for our Nanjing client. After finish testing, this model BS-D75 wire granulator will be transport Small capacity, capacity is 50-80kg/h; Support single-phase electricity, fit for home use.
mini copper wire granulator machine BS-S05 very well. Compared with other machines, the BS-S05 small cable wire recycling machine's design has more than two years of development, and we test and run it many times only for the best machine performance, so you can always trust manufacturers.
BS-D10 small cable granulator is a kind of dry-type copper recycling machine, which is mainly for crushing and separating waste copper particles and plastic skins, so as to achieve the purpose of recycling scrap copper from used waste cable wires. BS-D10 small wires granulator machine has a small volume and a small output and capacity of processing wires is about 100kg per hour, very suitable for recyclers with few cables or households. Dry-type small cable granulator does not need to add water for drying and separation, and this copper recycling machine is simple to operate the entire process only requires one worker, which saves both manpower and cost. The dust collection system of the copper granulator machine can effectively collect dust while complying with environmental protection requirements, energy saving, and environmental protection, with zero pollution and zero emissions. Technical data of this wire granulator machine: Model: BS-D10 small cable granulator Processing dimension: Below 20mm Machine Capacity:100KG/H Machine weight: 1100KG Machine size: 2300*1600*2000MM Motor power: 20KW Motor voltage: 380V/220V/customized
Copper wire recycling machine BS-N130 granulates and separates copper and plastic from electric wires, processing capacity is about 600-800kg per hour. After the crushing and separating process, scrap cable wires can be recycled into clean copper rice with a 99.9% high copper separating rate, are you interested For different kinds of scrap wires, the wire recycling machines capacity is as follows: 1. For 4 6 square wire, capacity can reach 600-800KG/H 2. For 1.5 2.5 square wire, capacity can reach 500-700KG/H 3. For car wire and plug wire, copper content is 45-50%, and capacity can reach 400-60KG/H 4. For mixed wire, copper content 20-30%, capacity can reach 300-500KG/H. Technology data of copper wires separator recycling machine: Name: Copper cable wire separator recycling machine Model: BS-N130 Processing dimension: Below 50mm Machine Capacity: 600-800KG/H Machine weight: 5000KG Machine size: 1200*3500*2250MM Motor power: 67KW Motor voltage: 380V/customized
Our D series cheap copper granulator machine is working, and this testing video show you the machine details and the working process. a professional copper recycling machine provider, and we supply high-quality copper recycling machines and the best services to our clients. D series copper wire recycling machine has small and medium processing capacity and has cheap prices, economical and practical. Do you like this model wire granulator
Is motor worth recycling Of course, it is worth to recycle copper winding wires from scrap motor. This new finished ST-400 motor cutting pulling machine is being tested for our Slovenia client. ST-400 motor cutting pulling machine, one kind of motor recycling machine, mainly used to cut and pull copper winding wires from motor stator. Processing range(motor diameter) is 90-260mm; Safe and high efficiency, very popular in Europe copper recycling field
Large capacity copper cable granulating machine BS-A1100 is our BSGH largest capacity copper wire recycling machine, which can process almost all types of waste cables with a capacity of 1.5-2T per hour. BS-A1100 copper cable granulator machine adopts an automatic pusher system for feeding scrap wires and forklift loading and feeding electric wires Instead of traditional manual feeding, feeding amount is large at a time and feeding speed is fast. A fully automatic operating system makes our wires copper recycling machine only need 1-2 skilled workers to operate too quickly and efficiently separate copper and plastic from waste cables so as to let you get the pure copper and pure plastic in the end. Technology data of copper cable recycling machine: Model: BS-A1100 Processing capacity: 1.5-2T/H Separation rate: 99.9% Machine weight: 17tons Motor Power: 128KW Motor Voltage: 380V/220V/customized
A car starter pulling machine is used in the final step of car starter dismantling, pulling out the copper winding from the scrap motor stator. After the insulating film melts, the copper wire pulling machine pulls copper wires from never cuts the stator side and complete dismantling and copper recycling of the entire automobile starter. Technical data of car starter puller machine: Machine Processing Efficiency: More than 350pcs/h Machine Weight: 460kg Package Weight: 500kg Machine Power: 4KW
Car starter heating machine is a kind of motor wrecker machine and is designed for recycling car starter motor. Car starter heating equipment is mainly used for rapid heating, and melting insulating film to cooperate with car starter pulling recycling machine to pull out copper winding wires because rotor copper wire is wrapped with a layer of the insulation film, which has a strong bonding effect. And this motor wrecker machine needs to be heated quickly by high-frequency heating equipment to melt the insulation film and facilitate copper winding wires pulling out to achieve scrap copper recycling. Technical data of this car starter recycling machine: Machine Name: Car starter heating machine Machine Processing Efficiency: More than 350pcs/h Machine Weight: 236kg Package Weight: 270kg Machine Size: 1.2 1.2 1.35M Package Size: 1.3 1.3 1.45M Machine Power: 85KW
Small copper wire granulator machine BS-D75 is used to separate copper granules and plastic granules from waste cable wires. This new model copper granulator machine has a small capacity and small size, very very fit for home use. This mini copper wire granulator machine BS-D75 processing capacity is about 50-80kg per hour, has a quick processing speed, and has high work efficiency. If you need a copper wire recycling machine to process wires in your home, this model mini cable granulator machine fits you well. Technical data of copper wire granulator machine: Machine Model: BS-D75 copper wire recycling machine Process Cable Diameter Range: Below 25mm Machine Capacity: 80-100KG/H Machine Weight: 1500kg Machine Size: 1700*1600*2200mm Motor Power: 18KW Advantages of small copper recycling machine: 1. Has mini size, mini capacity, and low noise, fit for home use; 2. High copper separating rate, and this model copper recycling machines copper separating rate can reach 99.9%; 3. Has the lowest price because of factory direct sale, fit for wholesale; 4. Automatic, save time and manpower for you; 5. The final product is pure copper and pure plastic, makes lots of money for you; Do you need to recycle your copper wires
Bestseller cable granulator machine BS-D20 is used to process waste cables that cannot be processed by a wire stripping machine, including automobile cables, communication cables, scrap wires, electric wires, and other cables diameter within 25mm. Copper and plastic are vibrated and separated by an air separator and vibrating tables after crushing, which can completely separate copper and plastic, and achieve the purpose of recycling waste cables. Of course, you also can add an electrostatic separation device on a copper wire granulator machine that can make the recovery rate of scrap copper close to 100%, which brings high economic benefits. Technical data of cable granulator machine: Model: BS-D20 Processing dimension: Below 20mm Machine Capacity: 200KG/H Machine weight: 1600KG Machine size: 2700*1700*2100mM Motor power: 28KW Motor voltage: 380V/220V/customized Welcome to know more about this small cable granulator machine
The electric motor puller machine from the a kind of copper recycling machine, used to pull all the copper winding wires from the motor stator. BSM-30 electric motor puller machine often works together with copper motor cutting machine, better recycling all the copper winding wires from the waste motor stator. Technology data of copper motor pulling machine: Machine model: BSM-30 Machine size: 2310*770*950mm Machine weight: 395kg Packing size: 2010*820*1050MM Packing weight: 420kg
BS-N125 copper wire granulator machine from the BSGH factory is a multifunctional copper recycling machine, that not only can process copper wires and aluminum wires, but also can process small radiators, transformers, fuses, and cable plugs. As a copper wire granulator machine BS-N125, first crushing the wasted copper wires, then separate the copper and plastic 100% and the separating rate can reach up to 99.9%. Output can be as higher as 3000-4000 kg per day. And you will get pure copper and pure plastic in the end. Technology data of copper cable granulator machine show for you: Model: BS-N125 Processing dimension: Below 20mm Machine Capacity: 300-500KG/H Machine weight: 3200KG Machine size: 390*200*225CM Motor power: 40.5KW Motor voltage: 380V/customized If you need to separate and recycle your copper wire, this copper recycling machine fits you well. Are you interested in making money by recycling copper from wires?
