Used and refurbished laptop, phones and tablets.
Copper cathodes and millberry.
HDPE and PP tigid scraps, ps from fridge scraps, r2 and r4 from weee recovery, pet film in rolls, pet flakes and bottles.
Tyre scrap, motor scrap, compressor scrap, paper scrap.
We have used alternator and starters scrap for sell at a very reasonable rate any serious buyer should contact us for more details.
A.c compressor scrap, mix motors scrap.
Iron & steel products.
Tyre bladders scrap, tyre bead wire, tyre side walls, used nylon conveyor belts, used electric motors, used fridge and air condition compressors, insulated copper wire, used rediator scrap, pvc plastic scrap.
A7 99.7 aluminium ingots
Hot-rolled steel channels This type of channel is produced according to GOST 535-88 with parallel flanges and sloping flanges: 10, 10P and etc. The slope of inner flanges must not exceed 10%. Assortment of the steel hot-rolled channel corresponds to GOST 8240-89. The number of the channel corresponds to its size (distance between the inner flanges) expressed in cm. For example: Channel #10 - distance between the inner flanges equals 10cm. All other parameters: flange width, wall thickness and etc. according to GOST. Channel that has letter A at the end of the number (14A) is a channel with sloping inner flanges, it means the flanges are wider and hence the weight of each meter is larger than ordinary channel. There are special types of hot-rolled channel: special channel for automotive industry - GOST 19425-74 (18S, 20S); special channel for wagon production - GOST 5267.1-90 (8W, 14W, 18W).
I-BEAM- double flanged - this type of products include hot rolled double flanged beams (I-beams), produced according to GOST 535-88. I-Beams are separated into several types: I-Beams with parallel flanges normal (20B, and etc.) wide flanges (20Sh and etc.) column (20K and etc.) I-Beams with sloping edges of flanges normal (edge slope 6-12%) GOST 8239-89 (â??10, 12, 16 and etc.) Assortment of such I-Beams corresponds to GOST 8239-89. Special (M and C): M - for hanging rails (edge slope not more than 12%): 18M, 24M, 30M and etc.; C - for reinforcement of mine shafts (edge slope not more than 16%): 14S, 20S and etc. Assortment of such double flanged beams corresponds to GOST 19425-74. The number of the I-beam is its conventional size (height) in cm.
Assortment corresponds to GOST 8509-93. Precision classes: A - high precision; B - ordinary precision. The number of equal flange steel corresponds to flange width, expressed in mm. For example: Angle 25 -flange width 25mm. All other sizes (wall thickness and etc.) according to GOST (shown in the table of GOST book of reference).
Hot-rolled flat bar - the most sought-after type of strip. Distinguish rolled dimensional (length 0.6 and 1.2 m), a multiple of the measured length and unmeasured (length 0.2 - 0.6 m). At the same time, a bar with a thickness of up to 4.5 mm is produced with a width of all sizes provided for by GOST. In accordance with GOST 103-76, the size of this product may vary in the range:length - 2-10m; width - 20 200 mm;thickness - 4 - 40 mm.
The material of manufacture and the range of the round bar in accordance with GOST 2590-2006, where the bar can be made of steel of the following grades: carbon (St3, St20, St35, St45); low alloyed (Steel 40X, Steel 40XH); high-alloyed (08 18 10, 38XH3MA, 40 2 14 17 2 and others), high-speed (U7; U7A; U8A)
Steel square can be made of steel of various grades: carbon - St3, St20, St35; St45 low alloyed - Steel 40X, Steel 40XH; high-alloyed - 08 18 10; 40XH2MA; 38XH3MA; 14 17�?2 and others high-speed - U7; U7A; U8A
Thermally strengthened periodically profiled steel rods of the diameter 6-40mm - the so called thermic is used for the construction of strategic reinforced concrete structures, GOST 10884-81. According to the standard this rebar is made out of these types of steel: AtIII - St (sp, ps); AtIV, AtIVK - 20GS, 25G2S, 35GS, 28S, 10GS2, 08G2S, 25S2P; AtV(K and SK) - 20GS, 20GS2, 08G2S, 10GS2, 28S, 25G2S, 35GS, 25S2R, 20HGS2; AtVII - 30HS2.
A Grade Electrolytic Copper Cathode
Aluminium Ingots
NOUR EDDINE offers several other types of products from those already mentioned. We have the ability to provide the following items in all sizes, standards and qualities: â?? - chromium bars and threaded rods; - cold drawn wire and hot-rolled wire rod; - hot rolled angles; - S.S. rebars; - blooms and billets; - ingots.
Copper Cathode from Middle East and CIS countries LME grade A (i.e. ASTM-B115) in various ranges and dimensions: Available: 10,000.00 MT/Month Delivery: SOHAR - OMAN A) Dimension : Length : 99 cm, Width: 98 cm Thickness: 5-20 mm Weight of each bundle: abt 2100-2500 kg No. of sheets in each bundle: 17 +/-3 Standard : ASTM-B115 B) Dimension : Length : 100 cm, Width: 100 cm Thickness: 15-17 mm Weight of each bundle: 1900-2500 kg No. of sheets in each bundle: 17 +/-3 Standard : ASTM-B115 C) Dimension :Length: 100 +/- 5 cm, Width: 101+/- 5 cm Thickness: 3-5 mm Weight of each bundle: 2200-2500 kg No. of sheets in each bundle: 50-60 Standard : ASTM-B115 D)Dimension :Length: 100 +/- 5 cm, Width: 101+/- 5 cm Thickness: 3-5 mm Weight of each bundle: 1400-1700 kg No. of sheets in each bundle: 40 Standard : ASTM-B115
